GB/T 15711-2018 PDF English
US$85.00 · In stock · Download in 9 secondsGB/T 15711-2018: Inspection of non-metallic inclusions of steel -- Etching test method of tower samples Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 15711: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 15711-2018 | English | 85 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Inspection of non-metallic inclusions of steel -- Etching test method of tower samples
| Valid |
| GB/T 15711-1995 | English | 199 |
Add to Cart
|
2 days
|
Steel products. Method for etch test of tower sample
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 15711-2018
GB/T 15711-2018: Inspection of non-metallic inclusions of steel -- Etching test method of tower samples
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT15711-2018
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.040.99
H 24
Replacing GB/T 15711-1995
Inspection of non-metallic inclusions of steel -
Etching test method of tower samples
Issued on: MAY 14, 2018
Implemented on: FEBRUARY 1, 2019
Issued by. State Administration for Market Regulation;
Standardization Administration of the PRC.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 5
3 Terms and definitions ... 5
4 Selection and preparation of samples ... 5
5 Hairline inspection method ... 8
6 Representation and assessment of inspection results ... 8
7 Test report ... 9
Inspection of non-metallic inclusions of steel -
Etching test method of tower samples
1 Scope
This Standard specifies the selection and preparation of samples, hairline
inspection method, representation and assessment of inspection results, and
test report, etc. for the use of etching test method of tower samples for
inspection of non-metallic inclusions of steel.
This Standard is applicable to the inspection of the number, length, and
distribution of hairlines in steel by etching test of tower samples of steel with a
diameter, side length, or thickness of 16 mm ~ 150 mm. Other products or
specifications may refer to.
2 Normative references
The following documents are indispensable for the application of this document.
For the dated references, only the versions with the dates indicated are
applicable to this document. For the undated references, the latest version
(including all the amendments) are applicable to this document.
GB/T 226 Test method for macrostructure and defect of steel by etching
GB/T 8170 Rules of rounding off for numerical values & expression and
judgement of limiting values
3 Terms and definitions
The following terms and definitions are applicable to this document.
3.1 Hairlines
The streaks formed by the non-metallic inclusions in steel extending in the
forging-rolling direction during processing and deformation.
4 Selection and preparation of samples
4.1 Sampling method
Table 1 (continued) (in millimeters)
Step No. Dimensions of each step, Di (Ti) Length, L
3 0.60D (0.60T) 50
Note. D - Diameter of round steel, side length of square steel; T - Thickness of flat steel
or steel plate.
a Through the negotiation between the supplier and the buyer, it can be sampled
according to the step length of L1=60 mm, L2=72 mm, and L3=90 mm.
4.3.3 The sample processing shall adopt a reasonable cutting process, to
prevent overheating. The surface roughness Ra of the sample after processing
shall be ≤1.6 μm.
4.3.4 The surface etching of the sample shall be in accordance with the
provisions of GB/T 226.
5 Hairline inspection method
5.1 The number, length, and distribution of hairlines on the entire surface of
each step are observed and inspected with the naked eye, and if necessary, a
magnifying glass of not more than 10 times can be used for inspection.
Note. It shall be noted that, during the inspection, the hairline is a non-metallic inclusion
streak, which shall be separated from the segregation line and the loose stripe zone
after etching. The latter is not included in the inspection results.
5.2 The test and inspection results shall comply with the provisions of GB/T
8170. The numerical values shall be rounded to single digit.
6 Representation and assessment of inspection results
6.1 The inspection results of hairlines shall include.
a) Number of hairlines on each step;
b) The total length of the hairline on each step, in millimeters (mm);
c) The total number of hairlines on each sample;
d) The total length of the hairline on each sample, in millimeters (mm);
e) The maximum length of the hairline on each sample, in millimeters (mm).
6.2 The starting-calculation length of the hairline shall comply with the
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 15711-2018 be delivered?Answer: The full copy PDF of English version of GB/T 15711-2018 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 15711-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 15711-2018_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 15711-2018 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 15711-2018?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 15711-2018 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 15711-2018?A step-by-step guide to download PDF of GB/T 15711-2018_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 15711-2018".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|