GB/T 14905-2020 PDF in English
GB/T 14905-2020 (GB/T14905-2020, GBT 14905-2020, GBT14905-2020)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 14905-2020 | English | 230 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Rubber and plastics hoses. Determination of adhesion between components
| Valid |
| GB/T 14905-2009 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Rubber and plastics hoses -- Determination of adhesion between components
| Obsolete |
| GB/T 14905-1994 | English | 439 |
Add to Cart
|
4 days
|
Rubber and plastics hose and hose assemblies. Wire reinforced. Hydraulic impulse test with flexing
| Obsolete |
Standards related to (historical): GB/T 14905-2020
PDF Preview
GB/T 14905-2020: PDF in English (GBT 14905-2020) GB/T 14905-2020
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 23.040.70
G 42
GB/T 14905-2020 / ISO 8033:2016
Replacing GB/T 14905-2009
Rubber and Plastics Hoses - Determination of
Adhesion between Components
(ISO 8033:2016, IDT)
ISSUED ON: NOVEMBER 19, 2020
IMPLEMENTED ON: OCTOBER 1, 2021
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative References ... 5
3 Terms and Definitions ... 6
4 Principle ... 6
5 Apparatus ... 6
6 Test Pieces ... 7
7 Procedure ... 11
8 Expression of Results ... 11
9 Test Report ... 12
Bibliography ... 18
Foreword
This Standard was drafted in accordance with the rules in GB/T 1.1-2009.
This Standard serves as a replacement of GB/T 14905-2009 Rubber and Plastics
Hoses - Determination of Adhesion between Components. In comparison with GB/T
14905-2009, the main technical changes are as follows:
---The Chapter “Terms and Definitions” is added (see Chapter 3);
---The scope of application of Type 7 test piece is expanded; it is applicable to
hoses whose spacing between adjacent coils of the helix is greater than 10 mm,
and also suggestions for the preparation of test pieces when the spacing
between adjacent coils of the helix is less than 10 mm are provided (see 6.3.8;
5.3.8 of Version 2009);
---Figure 1 ~ Figure 8 are modified, so that the representation of these figures can
be more accurate, and the misunderstandings of standard users can be
reduced (see Figure 1 ~ Figure 8; Figure 1 ~ Figure 8 of Version 2009).
This Standard uses the translation method in the equivalent adoption of ISO 8033:2016
Rubber and Plastics Hoses - Determination of Adhesion between Components.
The Chinese documents that have a consistent correspondence with the international
documents in the Normative References of this Standard are as follows:
---GB/T 2941-2006 Rubber - General Procedures for Preparing and Conditioning
Test Pieces for Physical Test Methods (ISO 23529:2004, IDT);
---GB/T 12833-2006 Rubber and Plastics - Analysis of Multipeak Traces Obtained
in Determinations of Tear Strength and Adhesion Strength (ISO 6133:1998,
IDT);
---GB/T 17200-2008 Technical Specification for Tensile, Compression and Flexural
Testing Machines for Rubber and Plastics (constant rate of traverse) (ISO
5893:2002, IDT).
This Standard was proposed by China Petroleum and Chemical Industry Federation.
This Standard shall be under the jurisdiction of National Technical Committee 35 on
Rubber & Products of Standardization Administration of China (SAC/TC 35).
The drafting organizations of this Standard: Shengli Oilfield Changlong Rubber &
Plastic Co., Ltd.; Shenyang Rubber Research & Design Institute.
The main drafters of this Standard: Mu Xuejie, Zhang Yigui, Wang Shuli.
Rubber and Plastics Hoses - Determination of
Adhesion between Components
1 Scope
Adequate adhesion between components of a hose is the basis for the hose to perform
well during use. This Standard specifies methods for the determination of the adhesion
between lining and reinforcement, between cover and reinforcement, between
reinforcement layers, between cover and outer lamination (thin layer of material
outside the cover for protection) and between lining and inner lamination (thin layer of
material inside the lining to reduce permeation of fluid into the lining). It covers all bore
sizes and the following types of hose construction:
---woven textile fabric;
---braided textile fabric;
---knitted textile fabric;
---circular-woven textile fabric;
---textile spiral;
---textile cord;
---wire braid;
---wire spiral;
---hoses containing a supporting helix.
Adequate adhesion between the various components of a hose is essential if it is to
perform satisfactorily in service.
2 Normative References
The following documents are indispensable to the application of this document. In
terms of references with a specified date, only versions with a specified date are
applicable to this document. In terms of references without a specified date, the latest
version (including all the modifications) is applicable to this document.
ISO 5893 Rubber and Plastics Test Equipment - Tensile, Flexural and Compression
Types (constant rate of traverse) - Specification
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|