GB 1886.332-2021 PDF English
US$125.00 · In stock · Download in 9 secondsGB 1886.332-2021: National food safety standard - Food additives - Calcium phosphate tribasic Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB 1886.332-2021 | English | 125 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
National food safety standard - Food additives - Calcium phosphate tribasic
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB 1886.332-2021
GB 1886.332-2021: National food safety standard - Food additives - Calcium phosphate tribasic---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB1886.332-2021
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
National Food Safety Standard -
Food Additives - Calcium Phosphate Tribasic
ISSUED ON: FEBRUARY 22, 2021
IMPLEMENTED ON: AUGUST 22, 2021
Issued by: National Health Commission of the People’s Republic of China;
State Administration for Market Regulation.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Molecular Formula and Relative Molecular Mass ... 4
3 Technical Requirements ... 4
Appendix A Inspection Methods ... 6
National Food Safety Standard -
Food Additives - Calcium Phosphate Tribasic
1 Scope
This Standard is applicable to the food additive tricalcium phosphate produced with
calcium hydroxide (or calcium carbonate) and food additive phosphoric acid (including
wet-process phosphoric acid) as raw materials, and it also applicable to food additive
tricalcium phosphate produced with calcium chloride solution and trisodium phosphate
as raw materials.
2 Molecular Formula and Relative Molecular Mass
2.1 Molecular formula
Proximate component: 10CaO•3P2O5•H2O
2.2 Relative molecular mass
1004.61 (as per 2018 international relative atomic mass)
3 Technical Requirements
3.1 Sensory requirements
The sensory requirements shall comply with the provisions of Table 1.
Table 1 – Sensory Requirements
3.2 Physicochemical index
The physicochemical index shall comply with the provisions of Table 2.
Appendix A
Inspection Methods
Caution: Some reagents used in this test method are toxic or corrosive, so
please be careful when operating! If necessary, perform it in a fume hood. If it
splashes on the skin, it shall be rinsed with water immediately, and the severe
cases shall be treated immediately.
A.1 General provisions
If no other requirements are specified, all the reagents and water used in this Standard
refer to the analytical reagents and Class-III water specified in GB/T 6682. If no other
requirements are specified, all the standard solution used in the test, standard solution
for determining the impurity, preparation and product shall be prepared according to
the provisions of GB/T 601, GB/T 602, GB/T 603.The solution used in the test refers
to the aqueous solution when the solvent is not specified.
A.2 Identification test
A.2.1 Reagents and materials
A.2.1.1 Nitric acid solution: 1+1.
A.2.1.2 Hydrochloric acid solution: 1+3.
A.2.1.3 Ammonia solution: 1+1.
A.2.1.4 Ammonium oxalate solution: 35g/L.
A.2.1.5 Ammonium molybdate solution: 60g/L, take 6g of ammonium molybdate
[(NH4)6MO7O24·4H2O] and dissolve it in 50mL water; slowly add 50mL nitric acid
solution while stirring; and store in a brown reagent bottle.
A.2.2 Identification method
A.2.2.1 Identification of calcium ions
Weigh about 0.1g of specimen; add 5mL of hydrochloric acid solution, 5mL of water;
heat to 40°C ~ 50°C. Add 1mL of ammonia solution while stirring; add 5mL of
ammonium oxalate solution; and a white precipitate is produced.
A.2.2.2 Identification of phosphate radical
Weigh about 0.1g of specimen; add nitric acid solution dropwise to dissolve the
specimen; then take 1mL of excessive nitric acid solution; heat to 40°C ~ 50°C; add
solution shall be 12.3~12.5. Continue to titrate with ethylenediaminetetraacetic acid
disodium salt (EDTA) standard titration solution until the solution appears clear blue
and keep it unchanged for 60s. At the same time, a blank test is performed.
Except for the blank test without adding the specimen, the other operations and the
types and amounts of the added reagents (except the standard titration solution) are
the same as the determination test.
A.3.1.5 Calculation of results
The mass fraction w1 of the trisodium phosphate (by Ca) shall be calculated as per
Formula (A.1).
Where:
V1 – volume of ethylenediaminetetraacetic acid disodium salt (EDTA) standard titration
solution consumed for titrating the specimen solution, in mL;
V0 – volume of ethylenediaminetetraacetic acid disodium salt (EDTA) standard titration
solution consumed for the blank test, in mL;
1000 – conversion factor;
c1 – concentration of ethylenediaminetetraacetic acid disodium salt (EDTA) standard
titration solution, in mol/L;
M1 – molar mass of the calcium (Ca), in g/mol [M1 =40.078];
m1 – mass of the specimen, in g.
The test results are based on the arithmetic mean of the parallel determination results.
The absolute difference between two independent determination results obtained
under repeatability conditions is no more than 0.2%.
A.3.2 Zinc sulfate back titration method (Method-II)
A.3.2.1 Method summary
In the specimen solution, add excessive ethylenediaminetetraacetic acid disodium salt
(EDTA) standard titration solution; complex with calcium ions; and use the KB mixture
as an indicator to titrate the excessive ethylenediaminetetraacetic acid disodium salt
(EDTA) standard titration solution by zinc sulfate standard titration solution.
A.3.2.2 Reagents and materials
Take about 0.5g of the specimen, accurate to 0.0002g; place it in a 100mL beaker;
moisten it with a small amount of water; and add 5mL of hydrochloric acid solution to
dissolve the sample completely. Transfer all to a 250mL volumetric flask; dilute to the
mark with water; and shake well. If necessary, dry filter, discard the first 20mL of filtrate.
Pipette 25.00mL of the above specimen solution; place it in a 500mL conical flask; then
use another pipette to transfer 25.00mL of ethylenediaminetetraacetic acid disodium
salt (EDTA) standard titration solution; add 50mL of water, 10mL of ammonia-
ammonium chloride buffer solution (A); shake well and stand for 5min. Add 2~3 drops
of KB indicator solution; titrate with zinc sulfate standard titration solution until the
solution changes from blue to blue-purple; and keep it for 30s without fading, which is
the end point. At the same time, a blank test is carried out.
Except for the blank test without adding the specimen, the other operations and the
types and amounts of reagents added (except the standard titration solution) are the
same as the determination test.
A.3.2.4 Calculation of results
The mass fraction w1 of tricalcium phosphate (by Ca) shall be calculated according to
Formula (A.3).
Where:
V5 - volume of zinc sulfate standard titration solution consumed by the blank test, in
mL;
V6 - volume of zinc sulfate standard titration solution consumed by titrating the
specimen solution, in mL;
1000 – conversion factor;
c4 – concentration of zinc sulfate standard titration solution, in mol/L;
M2 – molar mass of the calcium (Ca), in g/mol [M2=40.078]
m2 – mass of the specimen, in g;
25 – volume of pipetting the specimen solution, in mL;
250 – constant volume of specimen solution, in mL.
The test results are based on the arithmetic mean of the parallel determination results.
The absolute difference between two independent determination results obtained
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB 1886.332-2021 be delivered?Answer: The full copy PDF of English version of GB 1886.332-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB 1886.332-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB 1886.332-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 1886.332-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB 1886.332-2021?A step-by-step guide to download PDF of GB 1886.332-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB 1886.332-2021".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|