GB/T 9473-2022 PDF EnglishUS$245.00 · In stock · Download in 9 seconds
GB/T 9473-2022: Performance requirements for table lamps for paper task Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 9473: Historical versions
Similar standardsGB/T 9473-2022: Performance requirements for table lamps for paper task---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT9473-2022GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 29.140.40 CCS K 72 Replacing GB/T 9473-2017 Performance requirements for table lamps for paper task Issued on: DECEMBER 30, 2022 Implemented on: JANUARY 01, 2024 Issued by. State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 6 4 General requirements... 8 4.1 Safety requirements... 8 4.2 Radio disturbance characteristics... 8 4.3 Power supply harmonic current limit... 8 5 Technical requirements... 8 5.1 Appearance of lamps... 8 5.2 Marks... 8 5.3 Luminosity... 10 5.4 Color performance... 10 5.5 Modulation depth and temporal light artifact... 11 5.6 Power... 11 5.7 Power factor... 12 5.8 Electromagnetic radiation from table lamps to the human body... 12 5.9 Blue light hazards to the retina... 12 5.10 Noise... 12 6 Test methods... 12 6.1 General test conditions... 12 6.2 Appearance of lamps... 13 6.3 Marks... 13 6.4 Luminosity... 13 6.5 Chromaticity performance... 16 6.6 Modulation depth and temporal light artifact... 17 6.7 Power... 17 6.8 Power factor... 18 6.9 Electromagnetic radiation from table lamps to human body... 18 6.10 Blue light hazards to the retina... 18 6.11 Noise... 18 6.12 Test status description of dimmable/color-adjustable products... 19 6.13 Description of test status of table lamp with charging device... 19 Annex A (informative) Sector area illumination and illuminance uniformity test method ... 20 Annex B (normative) Calculation of chromaticity coordinate target values for flexible correlated color temperature TF... 21 Bibliography... 24 Performance requirements for table lamps for paper task1 ScopeThis document specifies the performance requirements for table lamps for paper task (hereinafter referred to as table lamps) that use tungsten filament lamps, fluorescent lamps or LEDs as light sources and a power supply voltage not exceeding 250 V. This document applies to table lamps used for reading and writing in homes, classrooms and similar places, and table lamps that claim to have similar functions such as "eye protection", "study", "work", etc., including table lamps with charging devices, table lamps with USB ports as power connection methods, and clip-on table lamps.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 6882, Acoustics -- Determination of sound power levels and sound energy levels of noise sources using sound pressure -- Precision methods for anechoic rooms and hemi-anechoic rooms GB 7000.1-2015, Luminaires -- Part 1.General requirements and tests GB 7000.204, Luminaires -- Part 2-4.Particular requirements -- Portable general- purpose luminaires GB/T 10682-2010, Double-capped fluorescent lamps -- Performance specifications GB 17625.1, Electromagnetic compatibility -- Limits -- Part 1.Limits for harmonic current emissions (equipment input current ≤16 A per phase) GB/T 17743, Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment GB/T 31275, Assessment of lighting equipment related to human exposure to electromagnetic field GB/T 31728, Portable luminaires with charging devices GB/T 36979, Measuring method of spatial distribution of color characteristics for LED products surface, the placement direction, etc. The description of the clip-on table lamps includes the effective work surface size and installation requirements applicable to the product, such as the minimum clamping depth of the clamp (the minimum width of the tabletop edge protruding outside) and the clamping thickness range. 3.6 modulation depth Modulation The ratio of the difference between the maximum and minimum values of the light output in one cycle to the sum of the maximum and minimum values of the light output. NOTE. The term "modulation depth" comes from IEEE Std 1789.The corresponding English term in GB/T 2900.65 is amplitude of fluctuation. The definitions of the two terms are the same. Modulation depth is expressed as a percentage. 3.7 temporal light artifact; TLA The visual perception of human observers in a specific environment caused by light stimuli whose brightness or spectral distribution fluctuates over time. NOTE. Visual change perception is the result of comparing the visual perception of an environment illuminated by modulated light with the visual perception of the same person when the same environment is illuminated by non-modulated light. [Source. CIE TN 006.2016, 2.4.1] 3.8 flicker For static observers in a static environment, light stimuli whose brightness or spectral distribution fluctuates over time induce visually unstable perceptions. NOTE 1.The temporal changes of light stimulation include periodic and non-periodic ones, which may be caused by the light source itself, the power supply or other influencing factors. NOTE 2.Flicker is a type of transient light artifact. [Source. CIE TN 006.2016, 2.4.2] 3.9 stroboscopic effect For static observers in non-static environments, changes in the perception of motion caused by light stimuli whose brightness or spectral distribution fluctuates over time. NOTE. The stroboscopic effect is a type of temporal light artifact. Example 1.When brightness changes in a periodic square wave, moving objects are perceived as discrete rather than continuous motion. a) For table lamps with replaceable light sources, the manufacturers and model specifications of the light sources allowed to be used shall be as follows. b) For table lamps with fluorescent lamps, the correlated color temperature shall be as per Annex D of GB/T 10682-2010. c) For LED table lamps, the product correlated color temperature or the adjustable range of correlated color temperature. For LED table lamps with adjustable color temperature, if the upper limit of the nominal correlated color temperature range exceeds 4000 K, there shall be a reminder including the following content. It is recommended to adjust the color temperature to below 4000 K when used at night. For LED table lamps with non-adjustable color temperature and a nominal correlated color temperature higher than 4000 K, there shall be a reminder including the following content. This table lamp is not suitable for use at night. d) General color rendering index Ra and (or) special color rendering index R9. e) Rated input power and power factor. f) The normal attitude of the table lamp, including. - The relative position between the light-emitting surface of the table lamp and the effective working area for lighting reading and writing tasks; - The height of the light-emitting surface; - The tilt angle of the light-emitting surface; - The placement and direction of the table lamp and other information. The clip-on table lamp shall state the effective work surface size and installation requirements for the product, such as the minimum clamping depth of the clamp (the minimum width protruding from the edge of the tabletop) and the clamping thickness range. g) Rated operating time of the table lamp with charging device. NOTE 1.The instruction manual can be in paper form or in electronic form, such as a QR code or other form. h) Table lamps shall claim one or more of the following characteristics of modulation depth and/or transient light artifacts. - LED table lamp modulation depth level specified in 5.5.2; - The threshold level at which stroboscopic effects and flicker may be observed is 5.7 Power factor The measured value of power factor shall not be lower than the nominal value by 0.05 or more. a) For table lamps with a power greater than 5 W and less than 25 W, the nominal power factor shall not be less than 0.5; b) For table lamps with a power greater than 25 W, the nominal power factor shall not be less than 0.9. NOTE. When the measured power is not less than 90% and not more than 110% of the rated input power, the limit value is determined according to the rated input power. When the measured power exceeds the above range, the limit value is determined according to the measured power. 5.8 Electromagnetic radiation from table lamps to the human body It shall comply with the requirements of GB/T 31275. 5.9 Blue light hazards to the retina According to GB/Z 39942-2021, the retinal blue light hazard category shall be RG0. 5.10 Noise The noise level of a table lamp containing a lamp control device shall not be greater than 25 dB(A) when operating normally.6 Test methods6.1 General test conditions 6.1.1 The test shall be carried out in a room without convection airflow, with relative humidity not exceeding 65% and an ambient temperature of 25℃±1℃. 6.1.2 Unless otherwise specified, the test shall be carried out at rated voltage and rated frequency. If the rated voltage is a range, it shall be measured at 220 V and 50 Hz. 6.1.3 The test power supply voltage and frequency error shall be kept within ±0.2% of the nominal value. 6.1.4 The total harmonic content of the test power supply voltage shall not be greater than 3%. 6.1.5 The accuracy of the electrical instruments used shall not be lower than Class 0.2. The accuracy of the illumination measuring instrument shall not be lower than Class 1 requirement in JJG 245. 6.1.6 Before the lamp brightness test, it shall be aged according to the relevant light source performance standards. 6.2 Appearance of lamps The external dimensions of the lamps shall be inspected with a general measuring tool with an accuracy of not less than 0.1 mm. The color and structure shall be inspected visually. 6.3 Marks The integrity of the marking content is checked visually. The firmness of the marking is checked by the method specified in 3.4 of GB 7000.1-2015. 6.4 Luminosity 6.4.1 Light blocking and anti-glare The working position of the table lamp during the shading and anti-glare tests shall be consistent with that during the illuminance and illuminance uniformity tests. Place the lamp on a level table in its normal attitude. Take measurements after the light source has stabilized. First, place the lens center of the luminance meter at a height of 400 mm from the table, 600 mm from the geometric center of the light source cavity surface, and perpendicular to the edge of the table. The position passes through the geometric center of the light source cavity surface, as shown in Figures 1 and 2.Then adjust the horizontal and vertical angles of the luminance meter during the test. Measure the surface brightness of all light sources, translucent components, and reflective components observed. For table lamps with the light-emitting surface in the normal attitude higher than 750 mm relative to the tabletop, the part above this height is exempted. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 9473-2022 be delivered?Answer: The full copy PDF of English version of GB/T 9473-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 9473-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 9473-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 9473-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 9473-2022?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 9473-2022 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 9473-2022?A step-by-step guide to download PDF of GB/T 9473-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 9473-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
