GB/T 26172.2-2010 English PDFUS$229.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 26172.2-2010: Foldaway beds -- Safety requirements and tests -- Part 2: Test methods Status: Valid
Basic dataStandard ID: GB/T 26172.2-2010 (GB/T26172.2-2010)Description (Translated English): Foldaway beds -- Safety requirements and tests -- Part 2: Test methods Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: Y81 Classification of International Standard: 97.140 Word Count Estimation: 10,114 Date of Issue: 2011-01-14 Date of Implementation: 2011-06-01 Quoted Standard: GB/T 10807-2006; GB 26172.1-2010 Adopted Standard: ISO 10131-2-1997, MOD Regulation (derived from): National Standard Approval Announcement 2011 No.2 (Total No.167) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies test methods for assessing indoor demolition safety requirements by the bed stacked turn. This section applies to already assembled and ready to use product. GB/T 26172.2-2010: Foldaway beds -- Safety requirements and tests -- Part 2: Test methods---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.. Foldaway beds Safety requirements and tests Part 2. Test methods ICS 97.140 Y81 National Standards of People's Republic of China By beds - Safety requirements and test methods for folding turn Part 2. Test methods Part 2. Testmethods (ISO 10131-2.1997, MOD) Issued on. 2011-01-14 2011-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsPreface Ⅰ 1 Scope 1 2 Normative references 1 3 1 General test requirements 4 Test apparatus 1 5 Test Procedure 2 6 Test report 5 Appendix A (informative) Test Method 6Foreword"Folding bed turned against safety requirements and test methods" is divided into two parts. --- GB 26172.1-2010 Rollaway bed turned against safety requirements and test methods - Part 1. Safety requirements; This section is "folded turning beds - Safety requirements and test methods rely on" Part 2. The partial modification of the use of ISO 10131-2.1997 "Part 2 - Safety requirements and test bed by folding turn. Test methods" (English Version), this part of ISO 10131-2.1997 compared to the main technical changes are as follows. --- Delete Normative references ISO 554. 1976 (see Chapter 2, ISO 10131-2. Chapter 21 997); --- Delete "Before the test, the specimen should be kept at least one week, in accordance with ISO 554 storage conditions of a temperature of (23 ± 2) ℃, relative humidity Degree (50 ± 5)% (see 3.2, ISO 10131-2.1997 Chapter 3); --- Modify the storage time before the test glued wood materials, that is, after "If the specimen is glue made of wood or similar material, the manufacturer shall Storage for at least four weeks in a normal indoor environment in order to carry out the test "to" if the specimen is made of glued wood or similar materials, from After the test is made to the front, at least under normal indoor environment continuously stored 7d "(see 3.2, ISO 10131-2.1997 Chapter 3). This section also made the following editorial changes. --- Use the decimal symbol instead of decimal symbol ",". ","; --- Page Change; --- Use the "standard" instead of "this International Standard"; --- With "This part of this standard" instead of "this part of this International Standard"; --- Added Appendix A (informative); --- Delete international standards informative overview of elements (including the cover, foreword and introduction). Appendix A of this section is an informative annex. This part is proposed by the China National Light Industry Council. This part of the furniture by the National Standardization Technical Committee (SAC/TC480) centralized. This section is responsible for drafting. Hangzhou torch Day Furniture Industry Co., Ltd., Shanghai Institute of Quality Supervision, Inspection; participated in the drafting of single Bit. Zhejiang Forestry College. The main drafters of this section. Lee Kuan Yew, Zhou Guan Song, wearing bell, Liuzhi Kun, Liu Yao country, Luo Jufen ancient Ming, Xu Jun, Hu Flourish. By beds - Safety requirements and test methods for folding turn Part 2. Test methods1 ScopeThis part of the standard specifies the method for assessing indoor test bed by the security requirements of the folding turn. This section applies to already assembled and ready for use product. This part is to simulate normal use and foreseeable misuse habit when folding bed by turning each part by strength tests under overload conditions have. This section is intended to evaluate the performance of products, not limited to material, shape and configuration process. Test results valid only for the subject sample. When the results of these tests to be used for other similar products, then the type of the test sample should have Representative product. For the structure of the sample program does not meet the test specimen, the test according to the procedure as stipulated performed and recorded with the prescribed test procedures difference.2 Normative referencesThe following documents contain provisions which, through this part of the standard reference in the provisions of this section. For cited documents with dates, with its After all of the amendments (not including errata content) or revisions do not apply to this section, however, encourage each agreement under this section Are Prescriptions can use the latest versions of these documents. For undated reference documents, the latest versions apply to this section. GB/T 10807-2006 Determination of soft foam polymeric material hardness (indentation method) (ISO 2439. 1980, IDT) GB 26172.1-2010 Rollaway bed turned against safety requirements and test methods - Part 1. Safety requirements (ISO 10131-2. 1997, MOD)3 General test requirements3.1 tolerance requirements In addition to other provisions, the tolerances are also required. --- Measuring all forces should be accurate to ± 5%; --- All quality measurements should be accurate to ± 0.5%; --- All size measurements should be accurate to ± 1mm. 3.2 Initial test preparation If the specimen is made of glued wood or similar materials, from pre-test to be made, at least in the general indoor environment of continuous storage 7d. When the delivery should be tested, if the specimen is removable, the product should be in accordance with assembly instructions for the product to be assembled, if the test Or a combination of parts can be assembled in different ways, then the test, the test shall be the most unfavorable manner specimen assembly or a combination of each. Before the test, the connector should be detachable fastening products. If the product has an adjustable property, it should be tested at both ends of their adjustable range limit position.4 Test Equipment4.1 General provisions Unless otherwise specified, the tests may use any suitable means for applying a load, because only the test results depends on proper loading, and It does not depend on equipment. 4.2 loading pad 200mm diameter rigid round object, the loading surface of the sphere, the spherical radius of curvature of 300mm, its surrounding Rounding radius Is 12mm (see FIG. 1). ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 26172.2-2010_English be delivered?Answer: Upon your order, we will start to translate GB/T 26172.2-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 26172.2-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 26172.2-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
