GB/T 19292.3-2018 English PDFUS$454.00 ยท In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 19292.3-2018: Corrosion of metals and alloys -- Corrosivity of atmospheres -- Part 3: Measurement of environmental parameters affecting corrosivity of atmospheres Status: Valid GB/T 19292.3: Historical versions
Basic dataStandard ID: GB/T 19292.3-2018 (GB/T19292.3-2018)Description (Translated English): Corrosion of metals and alloys -- Corrosivity of atmospheres -- Part 3: Measurement of environmental parameters affecting corrosivity of atmospheres Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H25 Classification of International Standard: 77.060 Word Count Estimation: 24,293 Date of Issue: 2018-05-14 Date of Implementation: 2019-02-01 Older Standard (superseded by this standard): GB/T 19292.3-2003 Quoted Standard: ISO 9223; ISO 11844-3 Adopted Standard: ISO 9225-2012, IDT Regulation (derived from): National Standards Announcement No. 6 of 2018 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration Summary: This standard specifies the method for the determination of environmental parameters used for corrosion evaluation. These parameters are used to classify atmospheric corrosion in GB/T 19292.1. The method for determining the environmental parameters specified in this standard is applicable to: 1. Normalized corrosion evaluation based on the corrosion rate of standard samples in the first year; 2. Corrosion evaluation based on the characteristics of exposed environments. This standard does not describe the analysis methods commonly used for environmental parameter testing, because these methods are derived from available analytical techniques in the laboratory. Comparisons between the SO2 and C1-subsidence rate-specific test methods and different test methods are described in Appendix A, Appendix B, Appendix C, Appendix D, Appendix E, and Appendix F. GB/T 19292.3-2018: Corrosion of metals and alloys -- Corrosivity of atmospheres -- Part 3: Measurement of environmental parameters affecting corrosivity of atmospheres---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Corrosion of metals and alloys.Corrosivity of atmospheres.Part 3. Measurement of environmental parameters affecting corrosivity of atmospheres ICS 77.060 H25 National Standards of People's Republic of China Replace GB/T 19292.3-2003 Corrosion of metals and alloys Part 3. Affecting the corrosive environment of the atmosphere Parameter measurement Part 3. Measurementofenvironmentalparametersaffectingcorrosivityof Atmospheres (ISO 9225.2012, Corrosionofmetalsandaloys-Corrosivityofatmospheres- Atmospheres, IDT) 2018-05-14 released.2019-02-01 implementation State market supervision and administration China National Standardization Administration issued ContentForeword III Introduction IV 1 Scope 1 2 Normative references 1 3 Principle 1 4 Humidity and temperature parameters 2 4.1 Relative humidity 2 4.2 Temperature 2 5 air pollutants 2 5.1 Principle 2 5.2 Placement of measuring instruments 2 5.3 Measurement method and duration 3 Appendix A (Normative) Determination of SO2 deposition rate on lead dioxide sulphated disks 5 Appendix B (Normative) Determination of SO2 deposition rate on a lead dioxide sulphation column 8 Appendix C (Normative) Determination of SO2 deposition rate on alkaline surfaces 11 Appendix D (Normative Appendix) Determination of Chloride Deposition Rate---Wet Candle Method 13 Appendix E (Normative Appendix) Determination of Chloride Deposition Rate---Dry Film Method 16 Appendix F (Normative) Comparison of chloride and SO2 deposition rates measured by different methods 19 Reference 20ForewordGB/T 19292 "Corrosion of Atmospheric Corrosion of Metals and Alloys" has been or is planned to be released as follows. --- Part 1. Classification, determination and evaluation; --- Part 2. Guidance values for corrosion levels; --- Part 3. Measurement of environmental parameters affecting atmospheric corrosivity; --- Part 4. Determination of corrosion rate of standard samples for evaluation of corrosivity. This part is the third part of GB/T 19292. This part is drafted in accordance with the rules given in GB/T 1.1-2009. This part replaces GB/T 19292.3-2003 "Corrosion of metals and alloys - Part 3. Measurement of contaminants", The main technical changes compared with GB/T 19292.3-2003 are as follows. --- Modified the title; --- Revised the scope of application (see Chapter 1); --- Added normative citations (see Chapter 2); --- Increased the principle of measuring atmospheric corrosive environmental parameters (see Chapter 3); --- Added provisions for temperature and relative humidity testing (see Chapter 4); --- Added provisions for the testing of atmospheric pollutant concentrations and settlements (see Chapter 5); --- Amend the provisions of the original standard for SO2 and Cl-deposition rate testing to a normative appendix (see Appendix A, Appendix C and Appendix) Record D, Chapter 2, Chapter 3, Chapter 4 of the.2003 edition); --- Increased the determination of SO2 deposition rate on a lead dioxide sulphation column (see Appendix B); --- Increased method for determination of Cl-deposition rate - dry film method (see Appendix E); --- Added a comparison between the Cl- and SO2 deposition rates obtained by different test methods (see Appendix F). This section uses the translation method equivalent to the international standard ISO 9225.2012 "Metal and alloy corrosion corrosive atmospheric impact Measurement of gas corrosive environmental parameters. The documents of our country that have a consistent correspondence with the international documents referenced in this part are as follows. --- GB/T 19292.1-2003 Corrosion of metals and alloys - Part 2. Classification, determination and evaluation (ISO 9223.1992, IDT); --- GB/T 24513.3-2012 Corrosion of metals and alloys - Classification of low-corrosion of indoor atmosphere - Part 3 Gas corrosive environmental parameter determination (ISO 11844-3.2006, IDT). This section has made the following editorial changes. --- Modified the standard name. This part was proposed by the China Iron and Steel Association. This part is under the jurisdiction of the National Steel Standardization Technical Committee (SAC/TC183). This section was drafted by. Qingdao Institute of Marine Corrosion, Institute of Metallurgical Industry Information Standards, Institute of Iron and Steel Research, Metals of Chinese Academy of Sciences Institute, Beijing University of Science and Technology, Qingdao Steel Research Nak Testing and Protection Technology Co., Ltd. The main drafters of this section. Ding Guoqing, Hou Jie, Yang Zhaohui, Yang Haiyang, Li Qian, Wang Zhenduo, Li Xiaogang, Liu Kaiji, Liu Wen, Han Wei. The previous versions of the standards replaced by this section are. ---GB/T 19292.3-2003.IntroductionThe main controlling factors that cause atmospheric corrosion of metals and alloys. the combined effects of temperature and humidity, as well as contaminants. Atmospheric corrosivity The basic requirement for evaluation is a standardized measurement of important parameters describing the correlation of corrosion and its environmental characteristics. Since the method is simple to operate and the results are highly contrasted, the methods in this standard have been adopted. It should be emphasized that GB/T 19292.1 gives The atmospheric corrosion evaluation method is based on the test method described in this standard. Warnings - some of the hazardous chemicals involved in some of the steps included in this section, therefore emphasizing the necessary safety Protective measures. Corrosion of metals and alloys Part 3. Affecting the corrosive environment of the atmosphere Parameter measurement1 ScopeThis part of GB/T 19292 specifies the method for the determination of environmental parameters for corrosion evaluation, using these parameters for GB/T 19292.1 Classification of atmospheric corrosivity. The method for determining the environmental parameters specified in this section applies to. --- Based on the normative corrosion evaluation of the corrosion rate of the first year of the standard sample; --- Informational corrosion assessment based on exposed environmental characteristics. This section does not describe the analytical methods commonly used in environmental parameter testing because they are derived from available analytical techniques in the laboratory. The relationship between the specific test methods for SO2 and Cl-sedimentation rates and different test methods is in Appendix A, Appendix B, Appendix C, and It is introduced in Record D, Appendix E, and Appendix F.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. Classification of corrosion and atmospheric corrosivity of ISO 9223 metals and alloys (Corrosionofmetalsandaloys-Corrosivity ofatmospheres-Classification,determinationandestimation) ISO 11844-3 Corrosion of metals and alloys - Classification of atmospheric corrosion - Part 3 Environmental parameter determination (Corrosionofmetalsandaloys-Classificationoflowcorrosivityofindooratmospheres- Part 3. Measurementofenvironmentalparametersaffectingindoorcorrosivity)3 PrincipleEnvironmental parameters and the different combinations between them can affect the corrosiveness of the atmosphere. Corrosion assessment (normative and information) is specified in ISO 9223 Two methods of sex. In general, for standard procedures for corrosion evaluation, two sets of parameters need to be obtained or determined. --- Humidity and temperature; --- Air pollutants. The standardized evaluation of corrosion is based on the information level of the main environmental parameters. temperature-humidity combined action, SO2 and airborne salt particle contamination dye. The primary purpose of testing these environmental parameters is to perform corrosion evaluation. In addition to SO2 and Cl- in air pollutants, others such as NOx, O3, H2S, and HNO3 also affect the corrosion rate. Active rot of sediment The etch components (SO2-4, NO-3, Cl-) react with metals in a humid environment and these factors are considered to be concomitant factors (see ISO 9223). These environmental parameters that affect the corrosion of standard metal coupons under specific conditions are not the primary reference for ISO 9223 for atmospheric corrosion assessment. number. However, the level of these parameter information contributes to the data corrosion assessment. ISO 11844-3 gives an environmental parameter test method for low-corrosion classification of indoor air. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 19292.3-2018_English be delivered?Answer: Upon your order, we will start to translate GB/T 19292.3-2018_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 19292.3-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 19292.3-2018_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 19292.3-2018?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 19292.3-2018 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
