GB 25579-2010 PDF EnglishUS$190.00 · In stock · Download in 9 seconds
GB 25579-2010: Zinc sulfate national food safety standards of food additives Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
GB 25579-2010: Zinc sulfate national food safety standards of food additives---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB25579-2010GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA Zinc sulfate national food safety standards of food additives ISSUED ON: DECEMBER 21, 2010 IMPLEMENTED ON: FEBRUARY 21, 2011 Issued by: Ministry of Health of PRC Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Molecular formula and relative molecular mass ... 4 4 Technical requirements ... 4 Appendix A (Normative) Test method ... 6 Appendix B (Informative) Treatment of mercury-containing waste liquid ... 12 Zinc sulfate national food safety standards of food additives1 ScopeThis standard applies to food additive zinc sulfate made from sulfuric acid and zinc oxide (or zinc hydroxide) as raw materials, or food additive zinc sulfate obtained by leaching and refining sphalerite with sulfuric acid after roasting.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard.3 Molecular formula and relative molecular mass3.1 Molecular formula Zinc sulfate monohydrate: ZnSO4·H2O Zinc sulfate heptahydrate: ZnSO4·7H2O 3.2 Relative molecular mass Relative molecular mass of zinc sulfate monohydrate: 179.49 (according to the 2007 international relative atomic mass) Relative molecular mass of zinc sulfate heptahydrate: 287.58 (according to the 2007 international relative atomic mass)4 Technical requirements4.1 Sensory requirements: It shall meet the requirements of Table 1.Appendix A(Normative) Test method A.1 Warning Some reagents used in the test methods of this standard are toxic or corrosive. Be careful when operating! If splashed on the skin, rinse with water immediately. In severe cases, seek medical treatment immediately. When using volatile acids, they must be carried out in a fume hood. A.2 General provisions The reagents and water used in the test methods of this standard, unless otherwise specified, refer to analytical pure reagents and grade 3 water specified in GB/T 6682- 2008. The standard solutions, impurity standard solutions, preparations and products required in the test shall be prepared in accordance with the provisions of HG/T 3696.1, HG/T 3696.2, HG/T 3696.3, unless otherwise specified. A.3 Identification test A.3.1 Identification of zinc ions A.3.1.1 Reagents and materials A.3.1.1.1 Chloroform. A.3.1.1.2 Acetic acid solution: 1 + 10. A.3.1.1.3 Sodium sulfate solution: 250 g/L. A.3.1.1.4 Dithizone carbon tetrachloride solution: 1 + 100. A.3.1.2 Analytical procedures Weigh about 0.2 g of the specimen; dissolve it in 5 mL of water; pipette 1 mL of the test solution; adjust the pH value of the solution to 4 ~ 5 with acetic acid solution; add 2 drops of sodium sulfate solution; add a few drops of dithizone carbon tetrachloride solution and 1 mL of chloroform; shake it; the organic layer will appear purple-red. A.3.2 Identification of sulfate A.3.2.1 Reagents and materials A.3.2.1.1 Barium chloride solution: 50 g/L. A.3.2.1.2 Hydrochloric acid solution: 1 + 1. A.3.2.2 Analytical procedure Take about 1 g of the specimen; dissolve it in water; add barium chloride solution to produce a white precipitate, which is insoluble in hydrochloric acid solution. A.4 Determination of zinc sulfate A.4.1 Method summary Dissolve zinc sulfate in sulfuric acid solution; add appropriate amount of water; add ammonium fluoride solution, thiourea, ascorbic acid as masking agents; adjust the pH to 5 ~ 6 with acetic acid-sodium acetate solution; use xylenol orange as an indicator; titrate with disodium ethylenediaminetetraacetic acid standard titration solution, until the solution changes from purple-red to bright yellow, which is the end point. A.4.2 Reagents and materials A.4.2.1 Ascorbic acid A.4.2.2 Thiourea solution: 200 g/L. A.4.2.3 Ammonium fluoride solution: 200 g/L. A.4.2.4 Sulfuric acid solution: 1 + 1. A.4.2.5 Acetic acid-sodium acetate buffer solution: pH≈5.5. A.4.2.6 Disodium ethylenediaminetetraacetic acid standard titration solution: c(EDTA) = 0.05 mol/L. A.4.2.7 Xylenol orange indicator solution: 2 g/L, use period not exceeding 1 week. A.4.3 Analytical procedure Weigh about 0.2 g of zinc sulfate monohydrate or 0.3 g of zinc sulfate heptahydrate sample, accurate to 0.0002 g; place in a 250 mL conical flask; add a small amount of water to moisten; add 2 drops of sulfuric acid solution to dissolve the specimen; add 50 mL of water, 10 mL of ammonium fluoride solution, 2.5 mL of thiourea solution, 0.2 g of ascorbic acid; shake well to dissolve; add 15 mL of acetic acid-sodium acetate buffer solution and 3 drops of xylenol orange indicator solution; titrate with disodium ethylenediaminetetraacetic acid standard titration solution, until the solution changes from red to bright yellow, which is the end point. Perform a blank test at the same time. In the blank test, except that no specimen is added, other operations and the types and amounts of reagents added (except standard titration solution) are the same as those for the test specimen. absorption value displayed by the instrument. Subtract the absorption value of the reagent blank solution from the absorption value of each working curve solution; draw the working curve with the mass of mercury (mg) in each solution as the abscissa and the corresponding absorption value as the ordinate. A.9.3.3 Determination of specimen solution The test solution is operated according to the provisions in A.9.3.2 from "Add 1 mL of stannous chloride..." until the absorption value of the solution is determined. Mercury- containing waste liquid is treated as shown in Appendix B. A.9.4 Result calculation The mercury content is expressed as the mass fraction w3 of mercury (Hg); the value is expressed in mg/kg and calculated according to formula (A.3): Where: m1 - The value of the mass of mercury in the specimen solution obtained from the working curve, in milligrams (mg); m - The value of the mass of the sample, in grams (g). The arithmetic mean of the parallel determination results is taken as the determination result; the absolute difference of the parallel determination results is not greater than 0.5 mg/kg. A.10 Determination of selenium Weigh 5.00 g ± 0.01 g of the specimen; place it in a 150 mL beaker; add 20 mL of water to dissolve it; add 1 mL of nitric acid solution (1 + 1); evaporate it to dryness on a water bath. The following is determined according to the hydride atomic fluorescence spectrometry of GB/T 5009.93-2010. A.11 Determination of arsenic Weigh 1.00 g ± 0.01 g of specimen; place in a conical flask; moisten with water; neutralize with hydrochloric acid to neutrality (check with pH test paper); then add 5 mL in excess and shake well. Transfer 2.00 mL of arsenic standard solution (1 mL solution contains 1.0µ of gAs) as a standard. Place in another conical flask. Add 5 mL of hydrochloric acid solution (1 + 3) to each. Then determine according to 6.2 or Chapter 11 of GB/T 5009.76-2003. The silver diethylaminodithiocarbamate colorimetric method is the arbitration method. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 25579-2010 be delivered?Answer: The full copy PDF of English version of GB 25579-2010 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 25579-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB 25579-2010_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 25579-2010 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB 25579-2010?A step-by-step guide to download PDF of GB 25579-2010_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 25579-2010". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
