GB 10395.6-2006 PDF EnglishUS$90.00 · In stock · Download in 9 seconds
GB 10395.6-2006: Tractors and machinery for agriculture and forestry -- Technical means for ensuring safety -- Part 6: Equipment for crop protection Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB 10395.6: Historical versions
Similar standardsGB 10395.6-2006: Tractors and machinery for agriculture and forestry -- Technical means for ensuring safety -- Part 6: Equipment for crop protection---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB10395.6-2006 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 65.060.01 B 90 Replacing GB 10395.6-1999 Tractors and machinery for agriculture and forestry - Technical means for ensuring safety - Part 6. Equipment for crop protection (ISO 4254-6.1995, MOD) Issued on: MARCH 29, 2006 Implemented on: NOVEMBER 1, 2006 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 6 2 Normative references ... 6 3 Terms and definitions ... 7 4 Technical requirements ... 7 5 Optional accessories (matched sprayers and automatic sprayers of tractors) ... 11 6 Safety signs ... 12 7 Use instructions ... 12Foreword4.1.1, 4.2.2, 4.2.6, Clause 5 and Clause 7 of this Part are recommended and the rest is mandatory. GB 10395 “Tractors and machinery for agriculture and forestry - Technical means for ensuring safety” consists of the following parts. - Part 1. General; - Part 3. Tractors; - Part 5. Power-driven soil-working machines; - Part 6. Equipment for crop protection; - Part 7. Combine harvesters, forage and cotton harvesters; - Part 8. Irrigation pumps and machines; - Part 9. Equipment for sowing, planting and distributing fertilizer; - Part 10. Walk-behind powered rotary tillers; - Part 11. Powered lawn trimmers; - Part 12. Portable powered hedge-trimmers; - Part 13. Powered walk-behind and hand-held lawn trimmers and lawn edge trimmers; - Part 14. Powered shredders and chippers; - Part 15. Powered edgers with rigid cutting means. This Part is Part 6 of the GB 10395 “Tractors and machinery for agriculture and forestry - Technical means for ensuring safety”. This Part revises and adopts ISO 4254-6.1995 “Tractors and machinery for agriculture and forestry - Technical means for ensuring safety - Part 6. Equipment for crop protection” (English version). This Part is redrafted according to ISO 4254-6.1995. Taking into account China’s national conditions, when using ISO 4254-6.1995, the following modifications are made. Tractors and machinery for agriculture and forestry- Technical means for ensuring safety - Part 6. Equipment for crop protection1 ScopeThis Part of GB 10395 specifies the safety requirements for power operated and manually operated equipment for crop protection and liquid fertilizer applicators. The requirements specified in this Part of GB 10395 are a supplement to GB 10395. 1.2 Normative referencesThe following standards contain provisions which, through reference in this Part of GB 10395, constitute provisions of this Part. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this Part are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies. GB/T 9480-2001 Tractors machinery for agriculture and forestry powered lawn and garden equipment - Operator’s manuals - Content and presentation (eqv ISO 3600.1996) GB 10395.1-2001 Tractors and machinery for agriculture and forestry - Technical means for ensuring safety - Part 1. General (eqv ISO 4254-1.1989) GB 10396-2006 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Safety signs and hazard pictorials - General principles (ISO 11684.1995, MOD) GB/T 18678-2002 Equipment for crop protection - Agriculture spray - Nominal capacity of spray tank and diameter of filling (eqv ISO 9357.1990) GB/T 20084-2006 Equipment for crop protection - Vocabulary (ISO 5681.1992, MOD) 4.2.1 Make sure that the liquid tank lid does not occur accidental loosening or opening. The liquid discharged from the liquid tank shall always be under the operator’s control. When the operator fills the liquid tank, it shall be able to directly see the liquid level indication or the liquid level position. 4.2.2 The rated capacity and the diameter of the filling hole of liquid tanks shall comply with GB/T 18678. 4.2.3 A filter shall be set at the filling hole. For compression sprayers that the filter can not be set due to structural restrictions, it shall ensure that there are at least two grades of filtrations. 4.2.4 Liquid tanks bearing pressure shall be set a device making the pressure drop to a safe pressure value in the event of failure. 4.2.5 Liquid tanks shall be capable of being conveniently and safely drained without using tools and contaminating the operator. 4.2.6 Sprayers of liquid tanks with a rated capacity greater than 800 L shall be equipped with a device for adding chemical liquids (such as pesticides) so that the chemical liquids do not need to be filled manually through the filling hole of liquid tanks. 4.2.7 The tightness of backpack sprayer’s liquid tank assembly shall meet the following requirements. after maintaining for 1 min at the pressure of 0.01 MPa, the liquid tank assembly shall be no leakage. 4.2.8 Liquid tanks of sprayers shall not leak and rupture after 3 consecutive fall tests. The temperature of the water during the fall test shall be kept within 20 °C ± 5 °C. The board is flat and hard and is a square with a side length of 0.9 m and a thickness of 0.05 m. a) Backpack sprayers. REMOVE the spray parts, air chamber, the lower and upper fixture rings of the liquid tank and other parts; BLOCK the outlet. FILL the liquid tank with a rated capacity of water; PUT the bottom of the tank downward horizontally; MAKE it fall freely from a height of 1 m ± 0.05 m on the board. b) Compression sprayers. REMOVE parts such as spray parts, straps; INSTALL a tee at the outlet to inflate and measure the pressure in the liquid tank. FILL the liquid tank with a rated capacity of water and inflate to the upper limit of working pressure; PUT the bottom of the tank downward horizontally; MAKE it fall freely from a height of 0.6 m ± 0.05 m on the board. NOTE. Appropriate safety measures shall be taken during the test. 4.3 Pressure indicator chamber is 3 times the maximum working pressure. 4.5 Spray rod and auxiliary device For filters and all parts contacting with the liquid, the structure shall be such that the liquid residue is of the least amount, and can be cleaned and drained. For sprayers with spray rods, it shall not be dangerous for personnel to carry out the spray operation when folding the spray rod, and shall not create a practical obstacle to the operator’s seat or prevent the operator from approaching the filling hole or any other positions. In the course of transport, sprayers with spray rods shall be fixed in a stable and reliable transport position. 4.5.1 Folding mechanism of spray rod When turning from the working position to the transport position, or from the transport position to the working position, it may cause squeezing and cutting hazards. a) For sprayers that change the position of the spray rod manually or with a mechanical auxiliary mechanism (such as a spring), a safety protection device shall be provided at the squeezing and cutting points. b) For sprayers that change the position of the spray bod with a powered auxiliary device (such as a hydraulic device), a safety warning mark shall be indicated near the squeezing and cutting points. c) The risk of squeezing and cutting shall be stated in the use instructions. 4.5.2 Fan/ventilation device For fans and ventilation devices, according to the condition of how close the operator to the air inlet and outlet, a safety distance complying with the specifications of 7.1.5 in GB 10395.1-2001 shall be ensured. If the above-mentioned safety distance can not be ensured due to structural or other reasons, to prevent accidental injuries, safety signs must be set close to the inlet and outlet; this risk shall be stated in the use instructions. When the fan impeller of backpack sprayers is at full load, carry out to the ultra-speed test at 1.3 times the calibrated speed, and repeat the test 3 times, each for 5 mm; after the test, the impeller shall be no damage, looseness, obvious deformation, etc. 4.5.3 Manually operated spray device Manually operated spray devices, such as spray guns, hand-held spray rods, shall be ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 10395.6-2006 be delivered?Answer: The full copy PDF of English version of GB 10395.6-2006 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 10395.6-2006_English with my colleagues?Answer: Yes. The purchased PDF of GB 10395.6-2006_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 10395.6-2006 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB 10395.6-2006?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 10395.6-2006 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB 10395.6-2006?A step-by-step guide to download PDF of GB 10395.6-2006_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 10395.6-2006". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
