HOME   Cart(1)   Quotation   About-Us Policy PDFs Standard-List
www.ChineseStandard.net Database: 189759 (19 Oct 2025)

JJG 525-2014 English PDF

US$599.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email.
JJG 525-2014: Verification Regulation of Wedge-feet Calibrator for Micrometers
Status: Valid

JJG 525: Evolution and historical versions

Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)StatusPDF
JJG 525-2014English599 Add to Cart 5 days [Need to translate] Verification Regulation of Wedge-feet Calibrator for Micrometers Valid JJG 525-2014
JJG 525-2002English599 Add to Cart 4 days [Need to translate] Verification Regulation of Wedge-feet Calibrator for Micrometers Obsolete JJG 525-2002
JJG 525-1988English319 Add to Cart 3 days [Need to translate] Verification Regulation of Wedge-feed Colibrator for Minimeter Obsolete JJG 525-1988

PDF similar to JJG 525-2014


Standard similar to JJG 525-2014

JJG 818   JJG 517   JJG 0061   JJG 658   JJG 601   

Basic data

Standard ID JJG 525-2014 (JJG525-2014)
Description (Translated English) Verification Regulation of Wedge-feet Calibrator for Micrometers
Sector / Industry Metrology & Measurement Industry Standard
Classification of Chinese Standard A52
Classification of International Standard 17.040
Word Count Estimation 26,252
Date of Issue 11/17/2014
Date of Implementation 5/17/2015
Older Standard (superseded by this standard) JJG 525-2002
Regulation (derived from) The State Administration of Quality Supervision, Inspection and Quarantine Notice 2014 No. 125
Issuing agency(ies) General Administration of Quality Supervision, Inspection and Quarantine
Summary This Standard applies to indexing is 1��m, 0.2��m, 0.1��m and 0.02 ��m ramp micrometer Calibrating the initial verification, use and subsequent verification check.

JJG 525-2014: Verification Regulation of Wedge-feet Calibrator for Micrometers

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Verification Regulation of Wedge-feet Calibrator for Micrometers State verification procedures People's Republic of China Ramp-type micrometer Calibrator Issued on. 2014-11-17 2015-05-17 implementation The State Administration of Quality Supervision, Inspection and Quarantine released Ramp-type micrometer Calibrator Verification Regulation Replacing JJG 525-2002 NFP. National Engineering Geometrical Parameters Measurement Technology Committee Main drafting unit. Henan Institute of Metrology Henan Medical Device Testing Sanmenxia Zhongyuan Measuring Instruments Ltd. This procedure works commissioned by the National geometric parameter measurement technology committee responsible for the interpretation The main drafters of this procedure. Huang Yuzhu (Henan Institute of Metrology) Gu Xiaojie (Henan Institute of Metrology) Hao Xiali (Henan Medical Device Testing) Liu Quan (Henan Institute of Metrology) YU Zhen River (Sanmenxia Zhongyuan Measuring Instruments Co., Ltd.)

table of Contents

Introduction (Ⅱ) 1 Scope (1) 2 Overview (1) 3 metering performance requirements (2) Face ramp and the anvil surface roughness of 3.1 (2) Flatness ramp face 3.2 (2) Readings from the outer drum 3.3 scale reticle plane edge to (2) 3.4 load lever probe (2) 3.5 Instrument indication error (2) 3.6 Return error (2) 3.7 Repeatability (2) 4 General Requirements (2) 4.1 Appearance (2) 4.2 Interaction of each part (3) 5 control of measuring instruments (3) 5.1 test conditions (3) 5.2 test project and the main test instrument (3) 5.3 Verification Methods (4) 5.4 Verification Results Processing (6) 5.5 test cycle (6) Appendix A Indexing is 1μm Calibrator (0 ~ 2) mm indication error range test sample (7) Appendix B stage three ribs technical requirements (8) Appendix C is 0.2μm oblique block indexing formula micrometer Calibrator (0 ~ 10) μm indication error of measurement Uncertainty Evaluation (9) Appendix D Indexing formula is 0.02μm lever ramp micrometer Calibrator (0 ~ 1) μm indication error of measurement Uncertainty Evaluation Results (13) Appendix E calibration certificate/test results in the notice page format (17)

Introduction

This procedure is prepared in accordance with JJF1002-2010 "national verification procedures to write rules" GB/T 24634-2009/ISO 14978.2006 "Geometrical Product Specifications (GPS measuring device universal concepts and to Seeking "and JJF1059.1-2012" Measurement Uncertainty and said that "the provisions of the JJG 525-2002 "Ramp type micrometer calibration device" subject to revisions. Compared with JJG 525-2002 "slant-block micrometer Calibrator" The main technical changes in addition to editorial changes outside as follows. --- Face to ramp block and the surface roughness of the test methods are described anvil; --- Increasing the load change metering performance requirements and the corresponding test methods; --- Modify the indexing formula is 0.2μm ramp micrometer (0-10) shows a value within the range of measurement error μm range limit The technical requirements; --- Revised indication error range of test methods, showing the value read from the subject point on the change in inductance micrometer Read the subject point on the ramp micrometer Calibrating the reading of the drum indication; --- Depending on dividing the value of the ramp dial gauge indication error test the range of the hysteresis error of technical indicators Its significant digits has been modified; --- Is 0.1μm, ramp micrometer readings Calibrating drum verification of indication error of indexing 0.2μm 2 blocks to use the same amount of direct method; --- The "change indication of" verification entries to "Repeatability" test method has been modified; --- Added Appendix A, B, C, D, E. The previous versions of this Recommendation published case. JJG 525-2002 JJG 525-1988 Ramp-type micrometer Calibrator Verification Regulation

1 Scope

The test procedures applicable to indexing is 1μm, 0.2μm, 0.1μm and 0.02μm ramp type micrometer Unit Given the initial verification, subsequent verification and the use of checks.

2 Overview

Ramp-type micrometer calibration device (hereinafter referred to as the Calibrator) is a use of helical or spiral ramp deputy and deputy, ramp and The principle of the lever combination, give the exact length of the amount of displacement measuring instruments, mainly for inductive, capacitive or grating Micrometer and pneumatic measuring and torsion spring comparator and other geometric measuring instruments verification or calibration. Verification is shaped according to their structure Type into spiral ramp and the lever-type vice Vice type categories spiral ramp, its shape shown in Figure 1, Figure 2.

1 spiral ramp deputy formula Calibrator

1- next to the probe clamping bracket; 2- axial clamping probe holder; ramp 3-; 4- scale; 5- reading drum; 6- differential screw; 7- anvil; 8- base; 9- oblique block Figure 2 spiral ramp lever vice formula Calibrator 1- ramp on the block; 2 - the lever; 3- axis probe clamping bracket holes; 4- spring fulcrum; 5- scale; 6- reading drum; 7- differential screw; 8- differential cylinder rod; 9- anvil; 10- ramp block; 11- base; 12- lever probe

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of JJG 525-2014_English be delivered?

Answer: Upon your order, we will start to translate JJG 525-2014_English as soon as possible, and keep you informed of the progress. The lead time is typically 3 ~ 5 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of JJG 525-2014_English with my colleagues?

Answer: Yes. The purchased PDF of JJG 525-2014_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.

Question 5: Should I purchase the latest version JJG 525-2014?

Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version JJG 525-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.