HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189760 (2 Nov 2024)

GB/T 35790.1-2017 Related PDF English

GB/T 35790.1-2017 (GB/T35790.1-2017, GBT 35790.1-2017, GBT35790.1-2017) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB/T 35790.1-2017English135 Add to Cart 0-9 seconds. Auto delivery. Specification for installation of the electronic identification of motor vehicles -- Part 1: Automobile GB/T 35790.1-2017 Valid GBT 35790.1-2017
Buy with any currencies (Euro, JPY, KRW...): GB/T 35790.1-2017    Preview this PDF: GB/T 35790.1-2017



GB/T 35790.1-2017 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 35.240.15 T 35 Specification for installation of the electronic identification of motor vehicles -- Part 1. Automobile ISSUED ON. DECEMBER 29, 2017 IMPLEMENTED ON. JULY 1, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of Contents Foreword . 3  1 Scope .. 4  2 Normative references . 4  3 Terms and definitions . 4  4 Requirements . 4  4.1 Installation mode.. 4  4.2 Installation position . 5  4.3 Installation conditions . 5  4.4 Installation steps .. 5  4.5 Pasting requirements . 6  Annex A (Normative) Schematic diagrams for the installation positions .. 7  Specification for installation of the electronic identification of motor vehicles -- Part 1. Automobile 1 Scope This Part of GB/T 35790 specifies the installation mode, installation position, installation conditions, installation steps and pasting requirements of the electronic identification of motor vehicles on the automobiles. This Part is applicable to the installation and acceptance of the electronic identification of motor vehicles on the front windshield of automobiles. 2 Normative references The following documents are essential to the application of this document. For dated references, only the editions with the dates indicated are applicable to this document. For undated references, only the latest editions (including all the amendments) are applicable to this document. GB/T 35789.1-2017 General specification for the electronic identification of motor vehicles -- Part 1. Automobile QB/T 4086 Glass cleaner 3 Terms and definitions The terms and definitions defined in GB/T 35789.1-2017 and the following ones are applicable to this document. 3.1 Aperture for radiowave The area without any films and metallic materials on the front windshield of an automobile, which is used for wireless signal transmission. 4 Requirements 4.1 Installation mode The electronic identification of motor vehicles shall be front facing the front of motor vehicles, and be attached to the inside of the front windshield of automobiles by means of an adhesive. 4.2 Installation position The requirements for the installation position of the electronic identification of motor vehicles are as follows. a) In case of equipped with the aperture for radiowave, the installation position is shown in Annex A, A.1. In case of no aperture for radiowave, it should be installed in the horizontal center and upper vertical position on the front windshield of vehicles. The installation position of different models shall be adjusted according to the actual situation, in order to obtain the best reading performance. For the installation position, SEE Annex A, A.2. b) After the installation of the electronic identification of motor vehicles, the distance between the outer edge and the film and the metallic material shall not be less than 10mm. c) The installation position shall not interfere with the driver’s vision and not distract the driver. 4.3 Installation conditions The installation conditions for the electronic identification of motor vehicles shall meet the following requirements. a) The front windshield shall be clean and dry; b) There shall be no metallic materials in the front windshield at the installation position, and there shall be no films on the surface; c) When the installation ambient temperature is lower than 10°C, the electronic identification of motor vehicles and the front windshield shall be preheated before pasting. 4.4 Installation steps The steps for installing the electronic identification of motor vehicles are as follows. a) For the front windshield with the film at the installation position, REMOVE the film at the installation position; b) USE a detergent that meets the requirements of QB/T 4086 to clean the installation position on the front windshield, so as to ensure that the paste position is clean and dry; c) CHECK the electronic identification of motor vehicles and the registration information of the vehicle to be loaded; d) REMOVE the double-sided adhesive protection paper of the electronic identification of motor vehicles; PASTE the electronic identification of motor vehicles to the designated installation position on the front windshield; e) After pasting, READ and TEST the electronic identification of motor ......

BASIC DATA
Standard ID GB/T 35790.1-2017 (GB/T35790.1-2017)
Description (Translated English) Specification for installation of the electronic identification of motor vehicles -- Part 1: Automobile
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard T35
Classification of International Standard 35.240.15
Word Count Estimation 10,142
Date of Issue 2017-12-29
Date of Implementation 2018-07-01
Drafting Organization Ministry of Public Security Traffic Management Science Institute
Administrative Organization Ministry of Public Security
Regulation (derived from) National Standards Bulletin 2017 No. 32
Proposing organization Ministry of Public Security of the People's Republic of China
Issuing agency(ies) People's Republic of China General Administration of Quality Supervision, Inspection and Quarantine, China National Standardization Administration