GB/T 11544-2012 (GB/T11544-2012, GBT 11544-2012, GBT11544-2012) & related versions
Buy with any currencies (Euro, JPY, KRW...): GB/T 11544-2012 Preview this PDF: GB/T 11544-2012
GB/T 11544-2012
GB
NATIONAL STANDARD OF THE
PEOPLE'S REPUBLIC OF CHINA
ICS 21.220.10
G 42
Replacing GB/T 11544-1997
Belt drives - Classical and narrow V-belts -
Dimensions (system based on datum width)
(ISO 4184:1992, Belt drives - Classical and narrow V-belts - Lengths in datum
system, MOD)
ISSUED ON: DECEMBER 31, 2012
IMPLEMENTED ON: OCTOBER 01, 2013
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 5
3 Terms ... 5
4 Cross-sectional size ... 6
5 Reference length ... 8
6 Deviation of reference length ... 11
7 Center distance change ... 11
8 Measurement method of size ... 12
Appendix A (Informative) Reference length of classical V-belt ... 15
Appendix B (Informative) Structural changes of this standard compared with
ISO 4184:1992 ... 16
Appendix C (Informative) Technical differences between this standard and ISO
4184:1992 AND their reasons ... 17
References ... 18
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard replaces GB/T 11544-1997 "Classical and narrow V-belts -
Dimensions". Compared with GB/T 11544-1997, the main technical changes
are as follows:
- DELETE the reference circumference of the type A 450 mm and type B 600
mm measuring pulleys, in the "Note" to Table 7 (8.1 in the 1997 edition);
- ADD "Note" to Table 7 (see 8.1);
- DELETE the marking (Chapter 9 of the 1997 edition);
- MODIFY the limit deviation of top width of measuring pulley AND the
measuring force of type A and type SPZ (see 8.1; 8.1 of the 1997 edition);
- DELETE the "Appendix A System based on effective width - V belt
dimensions" (Appendix A of the 1997 edition);
- DELETE the "Appendix B Grouping code of V-belt" (Appendix B of the 1997
edition).
This standard uses the redrafting method, to modify and adopt ISO 4184:1992
"Belt drives - Classical and narrow V-belts - Lengths in datum system".
Compared with ISO 4184:1992, this standard has many adjustments in
structure. Appendix B lists the comparison of clause numbers BETWEEN this
standard AND ISO 4184:1992.
Compared with ISO 4184:1992, there are technical differences between this
standard. The terms involved in these differences have been marked by a
vertical single line (︱) on the outer margin of the standard. Appendix C gives a
list of the corresponding technical differences and their reasons.
This standard was proposed by the China Petroleum and Chemical Industry
Federation.
This standard shall be under the jurisdiction of the Friction Belt Drive Sub-
committee of the National Belt Wheel and Belt Standardization Technical
Committee (SAC/TC 428/SC 3).
Drafting organizations of this standard: Zhejiang Sanlux Rubber Co., Ltd.,
Zhejiang Sanwei Rubber Products Co., Ltd., Weishi County Jiulong Rubber and
Plastic Co., Ltd., Wuxi Zhonghui Rubber Technology Co., Ltd., Zhejiang Kaiou
Transmission Belt Co., Ltd., Qingdao City Products Institute of Quality
Belt drives - Classical and narrow V-belts -
Dimensions (system based on datum width)
1 Scope
This standard specifies the cross-sectional dimensions, reference length,
reference length deviation, center distance change, size measurement
methods for classical V-belts and narrow V-belts.
This standard applies to classical V-belts and narrow V-belts (hereinafter
referred to as V-belts) for general mechanical transmission.
2 Normative references
The following documents are essential to the application of this document. For
the dated documents, only the versions with the dates indicated are applicable
to this document; for the undated documents, only the latest version (including
all the amendments) is applicable to this standard.
GB/T 321 Preferred numbers - Series of preferred numbers (GB/T 321-2005,
ISO3:1973, IDT)
GB/T 6931.2 Belt drives vocabulary - Part 2: V-belts and V-ribbed belt drives
vocabulary (GB/T 6931.2-2008, ISO 1081:1995, MOD)
GB/T 10412 classical and narrow V-belt wheels (standard width system)
(GB/T 10412-2002, ISO 4183:1995, MOD)
GB/T 11356.1 Grooved pulleys for classical and narrow V-belts (system
based on datum width) (GB/T 11356.1-2008, ISO 255:1990, MOD)
GB/T 13490 V-belts - Uniformity of belts - Test method for determination of
center distance variation (GB/T 13490-2006, ISO 9608:1994, IDT)
3 Terms
The terms and definitions of V-belt drive, which are defined in GB/T 6931.2,
apply to this document.
4 Cross-sectional size
V-belts, which have cross-sections of type Y, Z, A, B, C, D, E are called classical
V-belts. The V-belts, which have cross-sections of types SPZ, SPA, SPB, SPC
are narrow V-belts. For classical V-belts and narrow V-belts in the standard
width system, the corresponding basic widths of the pulley grooves are
specified as follows:
- Type Y (for groove type, which has a reference width of 5.3 mm)
- Type Z (for groove type, which has a reference width of 8.5 mm)
- Type A (for groove type, which has a reference width of 11 mm)
- Type B (for groove type, which has a reference width of 14 mm)
- Type C (for groove type, which has a reference width of 19 mm)
- Type D (for groove type, which has a reference width of 27 mm)
- Type E (for groove type, which has a reference width of 32 mm)
- Type SPZ (for groove type, which has a reference width of 8.5 mm)
- Type SPA (for groove type, which has a reference width of 11 mm)
- Type SPB (for groove type, which has a reference width of 14 mm)
- Type SPC (for groove type, which has a reference width of 19 mm)
The nominal size of the cross-section of the V-belt is as shown in Figure 1 and
Table 1. Whether the cross-section size is qualified or not, is judged by applying
the measuring force, which is specified in Table 7, on the length measuring
machine, to measure the exposed height f of the V-belt in the pulley groove (see
Figure 2). Table 2 shows the specified value of the exposed height of the V-belt.
Note: Refer to Table 1 for V-belts, which have teeth on the bottom side.
Where:
αmax - The maximum center distance of the two pulleys, in millimeters (mm);
αmin - The minimum center distance of the two pulleys, in millimeters (mm);
cd - Reference circumference of the measured pulley (see Table 7), in
millimeters (mm).
8.3 Measurement of exposure height
Install the measured V-belt in the grooves of the two pulleys of the length
measuring machine. The measuring force, as shown in Table 7, is applied to
the V-belt, through the movable pulley. Rotate the V-belt for 1 ~ 3 turns, to make
the V-belt fit into the groove of the pulley correctly. After it stops stably, measure
the exposed height of the V-belt in the groove, at the center of the belt top width,
at any point of the contact arc, BETWEEN the V-belt AND the pulley. However,
be careful not to measure on the V-belt where there are cloth joints and
trademarks. Take the average value of any three points measured, as the
measurement result of exposed height.
8.4 Measurement of center distance change
The measurement of the center distance change is carried out in accordance
with the provisions of GB/T 13490.
......
Standard ID | GB/T 11544-2012 (GB/T11544-2012) | Description (Translated English) | Belt drives. Classical and narrow V-belts. Dimensions(system based on datum width) | Sector / Industry | National Standard (Recommended) | Classification of Chinese Standard | G42 | Classification of International Standard | 21.220.10 | Word Count Estimation | 15,176 | Older Standard (superseded by this standard) | GB/T 11544-1997 | Quoted Standard | GB/T 321; GB/T 6931.2; GB/T 10412; GB/T 11356.1; GB/T 13490 | Adopted Standard | ISO 4184-1992, MOD | Drafting Organization | Rubber Co., Ltd., Zhejiang Sanlux | Administrative Organization | National Standardization Technical Committee pulley and the belt friction belt drive Technical Committee | Regulation (derived from) | National Standards Bulletin No. 41 of 2012 | Proposing organization | China Petroleum and Chemical Industry Federation | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China | Summary | This standard specifies the common V belt and narrow V-belt cross-sectional dimension, the reference length, the reference length deviation, the center distance variation, measurement methods. This standard applies to general mechanical transmission with | Standard ID | GB/T 11544-1997 (GB/T11544-1997) | Description (Translated English) | Classical and narrow V-belts--Dimensions | Sector / Industry | National Standard (Recommended) | Classification of Chinese Standard | G42 | Classification of International Standard | 21.220.10; 83.140.01 | Word Count Estimation | 13,136 | Date of Issue | 1997/10/14 | Date of Implementation | 1998/4/1 | Older Standard (superseded by this standard) | GB 11544-1989 | Quoted Standard | GB/T 321-1980; GB/T 5756-1986; GB/T 6931.2-1986; GB 11356-1989; GB/T 13490-1992 | Adopted Standard | ISO 4184-1992, MOD; BS 3790-1981, MOD; ANSI/RMA IP-22-1983, MOD; BS 3790-1981, MOD | Drafting Organization | Qingdao Rubber Industry Institute | Administrative Organization | Qingdao Rubber Industry Institute | Regulation (derived from) | National Standards Bulletin 2012 No. 41 | Proposing organization | Ministry of Chemical Industry of the People Republic of China | Issuing agency(ies) | State Bureau of Technical Supervision | Summary | This Standard specifies the general cross-sectional dimension of V-belt and narrow V-belt (hereinafter referred to as V-belt), the reference length and limit deviations, exposing the height of the center distance variation, labeled and size measurement methods. This standard applies to general mechanical transmission with ordinary V-belt and narrow V-belts. | Standard ID | GB/T 11544-1989 (GB/T11544-1989) | Description (Translated English) | Classical and narrow V-belts-Dimensions | Sector / Industry | National Standard (Recommended) | Classification of Chinese Standard | G42 | Date of Issue | 1989/7/15 |
|