QC/T 707-2004 PDF EnglishUS$110.00 · In stock · Download in 9 seconds
QC/T 707-2004: Technical specification for center box for motor vehicles Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsQC/T 707-2004: Technical specification for center box for motor vehicles---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QCT707-2004QC AUTOMOBILE INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA Technical specification for center box for motor vehicles Issued on: FEBRUARY 10, 2004 Implemented on: AUGUST 1, 2004 Issued by. National Development and Reform Commission Table of ContentsForeword ... 5 1 Scope ... 6 2 Normative references ... 6 3 Terms and definitions ... 6 4 Requirements... 7 5 Test methods ... 11 6 Inspection rules ... 13 7 Marking, packaging, storage and preservation ... 14 Annex A (normative) Load procedure of center boxes ... 15 Annex B (normative) Test load of center boxes ... 16 Annex. Number and name of 15 automotive industry standards No. Standard No. Standard name No. of the standard being replaced 1 QC/T 698.1-2004 Vehicle instructions - Part 1. Vehicle registration technology parameter table 2 QC/T 459-2004 Truck with loading crane QC/T 459-1999 3 QC/T 699-2004 Tail-lift for vehicle 4 QC/T 700-2004 General technical specification of cylinder head for motorcycles and mopeds 5 QC/T 701-2004 Mounting of rear shock absorbers for motorcycles and mopeds 6 QC/T 702-2004 Method of reliability test for catalytic converter of motorcycles and mopeds 7 QC/T 27-2004 Bench test method of automobile clutch QC/T 27-1992 8 QC/T 25-2004 Technical specification of automobile clutch QC/T 25-1992 9 QC/T 703-2004 Specification of PU foam wrap layer for auto steering-wheel 10 QC/T 704-2004 Test method of PU foam wrap layer integer hardness for auto steering-wheel 11 QC/T 705-2004 Electronic bus-stop annunciator onboard motor coach 12 QC/T 706-2004 Technical specification of silicon avalanche rectification for motor vehicles 13 QC/T 707-2004 Technical specification of center box for motor vehicles 14 QC/T 30-2004 Technical specification of electric horn for motor vehicles QC/T 30-1992 15 QC/T 29106-2004 Technical specification of automobile wire harness QC/T 29106-1992ForewordThis Standard is the firstly-developed product standard of center box for motor vehicles. In addition to the technical requirements referencing to foreign advanced standards, the other content and the editing of the standard comply with the relevant specifications of GB/T 1 “Directives for standardization” and QC/T 413 “Basic technical specifications for electrical equipment of automobiles”. Annex A and Annex B of this Standard are normative. This Standard is proposed by China Association of Automobile Manufacturers. This Standard is under the jurisdiction of National Technical Committee on Automobile of Standardization Administration of China. Drafting organizations of this Standard. Harbin Feiban Automobile Electric Appliance Co., Ltd., Hebi Tianhai Automobile Electric Appliance Co., Ltd., Shanghai Xinguang Automobile Electric Appliance Co., Ltd. Main drafters of this Standard. Luo Ruoxiao, Wang Lisheng, Zhong Huaguang, Wang Rongxi, Gu Shujian. Technical specification for center box for motor vehicles1 ScopeThis Standard specifies terms and definitions, requirements, test methods, inspection rules, marking, packaging, storage and preservation of center box for motor vehicles. This Standard applies to center box for motor vehicles (hereinafter referred to as center box).2 Normative referencesThe following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies. QC/T 413-2002 Basic technical specifications for electrical equipment of automobiles QC/T 417.1-2001 Automotive wire harness connectors - Part 1. Definitions, test methods and general performance requirements (automotive part)3 Terms and definitionsFor the purpose of this Standard, the following terms and definitions apply. 3.1 connecting plug A conductive part of an electrical device on the center box used to electrically connect to an external circuit. 3.2 connecting socket A socket on the center box for connection to a relay plug or chip fuse with a certain clamping force. 3.3 insertion force The force required to insert the relay, fuse or standard insert into the center box. 3.4 withdrawal force The force required to withdraw the relay, fuse or standard insert from the center box. 3.5 bridge blade In the measurement of voltage drop, a kind of blade with different shapes used to connect the parts need energization and conduction after removing the relay or fuse.4 Requirements4.1 General requirements The center box shall comply with the specifications of this Standard and shall be manufactured according to the drawings and design documents approved by the prescribed procedures. 4.2 Temperature range The center box is continuous rating. It shall be able to normally turn on and off within the temperature range of 40 °C ~ 70 °C (in the cab), -40 °C ~110 °C (under the engine hood), the storage temperature is -40 °C ~ 90 °C (in the cab), -40 °C ~ 130 °C (under the engine hood) respectively. 4.3 Shape and installation dimension The shape and installation dimension of the center box shall comply with the specifications of the drawings of the product. Among them, the electrical connection of the external circuit is not allowed to use riveting and welding. 4.4 Appearance The center box shall have no damage after being subjected to the resistance to disruptive voltage strength test with an actual sinusoidal voltage of 50 Hz, an effective value of 1000 V and a duration of 1 min. 4.10 No-load ventilation storage performance The center box shall be subjected to a no-load ventilation storage test at 90 °C (in the cab) and 130 °C (under the engine hood) for 48 h. After the test, it shall be able to normally turn on and off, and shall comply with the specifications of 4.4 in this Standard. 4.11 Resistance to low temperature The center box shall be able to normally turn on and off at -40 °C, and shall comply with the specifications of 4.4 in this Standard. The voltage drop allows an increase of 20 %. 4.12 Resistance to temperature alternation The center box shall be subjected to a total of 4 cycles (6 h for one cycle) in the temperature range of -40 °C ~ 70 °C (in the cab) and -40 °C ~ 110 °C (under the engine hood). After the test, it shall be able to normally turn on and off, and shall comply with the specifications of 4.4 in this Standard. The voltage drop allows an increase of 20 %. 4.13 Resistance to temperature and humidity cycle The center box shall be subjected to a total of 10 cycles (24 h for one cycle) of the temperature and humidity combined cycle test. After the test, it shall be able to normally turn on and off, and shall comply with the specifications of 4.4 in this Standard. The voltage drop allows an increase of 20 %. 4.14 Vibration resistance The center box shall be subjected to the sweeping vibration test according to the specifications of Table 3 “Other parts” in QC/T 413-2002. After the test, it shall be able to normally turn on and off, and shall comply with the specifications of 4.4 and 4.7 in this Standard. 4.15 Durability (load ventilation storage) The durability test of the center box shall be carried out by selecting the corresponding load procedure and test load from Figure A.1 of Annex A and Table B.1 of Annex B according to the product function and customer requirements, at the ambient temperature of 70 °C (in the cab) and 110 °C (under the engine hood) for 24 h. After the test, it shall be able to normally turn on and off, and shall comply with the specifications of 4.4 in this Standard. The voltage drop allows an increase of 20 %. The overcurrent test of the center box shall be carried out on a dedicated test stand which can automatically display the values. During the test, according to different product features and customer requirements, select corresponding load procedure and test load from Figure A.1 and Table B.1, apply the current of 1.1 times the rated value of the fuse, for 1 h. After the test, it shall comply with the specifications of 4.8 in this Standard. 5.9 Resistance to disruptive voltage strength test When having resistance to disruptive voltage strength test, firstly put the center box into the hot and humid chamber, to keep 24 h in a condition with the temperature of 18 °C ~ 28 °C and the relative humidity of 90 % to 98 %; remove and replace it at the normal environment for 1 h; apply 50 Hz 1000 V actual sine wave voltage between mutually insulated conductive parts and between the conductive parts and the enclosure. The voltage applied at the beginning of the test shall be less than 500 V and then steadily increased to a full value for a period of not less tha... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of QC/T 707-2004 be delivered?Answer: The full copy PDF of English version of QC/T 707-2004 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of QC/T 707-2004_English with my colleagues?Answer: Yes. The purchased PDF of QC/T 707-2004_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QC/T 707-2004 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of QC/T 707-2004?A step-by-step guide to download PDF of QC/T 707-2004_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "QC/T 707-2004". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
