HG/T 4304-2012 PDF EnglishUS$120.00 · In stock · Download in 9 seconds
HG/T 4304-2012: Anti-Corrosion technical conditions for equipment lined with polyolefine (PO) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsHG/T 4304-2012: Anti-Corrosion technical conditions for equipment lined with polyolefine (PO)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/HGT4304-2012HG CHEMICAL INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.140.30 J 16 Record No.. 38695-2013 Anti-corrosion technical conditions for equipment lined with polyolefine (PO) Issued on: DECEMBER 28, 2012 Implemented on: JUNE 1, 2013 Issued by. Ministry of Industry and Information Technology of the People's Republic of China Table of ContentsForeword ... 4 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 6 4 Classification and application conditions ... 7 4.1 Classification ... 7 4.2 Marking ... 7 4.3 Structure type ... 7 4.4 Application conditions ... 8 5 Technical requirements ... 8 5.1 Appearance quality ... 8 5.2 Materials ... 9 5.3 Shell ... 9 5.4 Structure size ... 9 5.5 PO lining ... 11 5.6 Pressure resistance ... 12 6 Test methods ... 12 6.1 Appearance ... 12 6.2 Size measurement ... 12 6.3 Electric spark detection ... 12 6.4 Pressure test ... 12 6.5 Temperature resistance test ... 13 6.6 Thermal expansion and contraction test ... 13 6.7 Peel strength measurement ... 13 6.8 Health quality assessment ... 13 7 Inspection rules ... 13 7.1 Exit-factory inspection ... 13 7.2 Type inspection ... 14 8 Marks, packaging, transport, storage ... 14 8.1 Marks ... 14 8.2 Packaging ... 14 8.3 Transport ... 14 8.4 Storage ... 14 Annex A (informative) PO/C.S lining product corrosion resistance ... 15 Anti-Corrosion technical conditions for equipment lined with polyolefine (PO)1 ScopeThis Standard specifies the terms and definitions, classification and application conditions, technical requirements, test methods as well as inspection rules and marks, packaging, transport, storage of anti-corrosion polyolefin (Polyolefine, hereinafter referred to as PO) plastic-lined steel piping and equipment. This Standard is applicable to PO rotational casting lining steel (hereinafter referred to as C.S) piping and equipment of which the nominal pressure PN is 0.098MPa ~ 1.6MPa, temperature for use is 20°C ~ 100°C, nominal diameter is DN25mm ~ DN8000mm.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB 150, Steel pressure vessel GB/T 700, Carbon structural steels GB/T 1047, Pipework components - Definition and selection of DN (nominal size) GB/T 1048, Nominal pressure for pipe components GB/T 1804, General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications GB/T 5117, Carbon Steel Covered Electrodes GB/T 7122, Adhesives-Determination of peel resistance of high-strength adhesive bonds - Floating roller method GB/T 8163, Seamless steel tubes for liquid service GB/T 8923, Preparation of steel substrates before application of paints and 5.2 Materials 5.2.1 PO material is made of polyolefin resin such as high-quality polyethylene (PE) and polypropylene (PP) as the main raw materials, and is mixed with a reasonable ratio. Its performance indicators shall meet the requirements of Table 2. Polyethylene (PE) resin shall meet the requirements of GB/T 11115. Polypropylene (PP) resin shall meet the requirements of GB 12670. Table 2 -- Performance indicators of PO material Item Melting temperature/°C Tensile strength/MPa Elongation at break/% Performance indicator 180~220 10~18 300~500 5.2.2 Shell seamless steel pipe, flange, steel plate material is 20, Q235 or equivalent material. And, the seamless steel pipe shall comply with the provisions of GB/T 8163; the flange shall comply with the provisions of HG/T 20592; Q235 shall comply with the provisions of GB/T 700. 5.2.3 The selection of welding materials and their requirements shall comply with the provisions of Annex D of GB 50236-1998 and GB 5117, respectively. 5.3 Shell 5.3.1 When the nominal diameter DN≤300, the shell uses seamless steel pipe. 5.3.2 All welds of shell manufacturing must be completed before lining construction. 5.3.3 Shell thickness, welding process and technical requirements shall comply with the provisions of JB/T 4735, GB 150, GB 50316 and HG/T 20678. 5.3.4 The surface to be lined shall be a smooth surface or plane. The corners of the structure and the fillet welds must adopt a circular transition. The fillet radius shall be no less than 5 mm. 5.3.5 The plane to be lined must be rusted. The treated surface shall meet the St2 or BFI requirements of GB/T 8923. 5.4 Structure size 5.4.1 The nominal diameter of the piping is selected in accordance with GB/T 1047. 5.4.2 The nominal diameter of the equipment is selected in accordance with the provisions of GB/T 9019. 5.4.3 The connection flange selects HG/ T 20592 plate flat welding flange. Other flange types in HG/T 20592 series, other flange standards (such as GB, JB, SY, ANSI, JIS, DIN, etc.) or special ones can also be selected according to Table 5 -- PO lining composite indicator Item PO lining composite indicator Peel strength/(N/cm-50 mm/min) ≥60 NOTE. The unit in the table indicates the force used to peel the unit width (cm) sample at the peeling speed (50 mm/min). 5.5.6 Hygienic quality If the product is used in a place where drinking water is safe, the sanitary quality of the PO lining shall comply with the provisions of GB/T 17219. 5.6 Pressure resistance For the conditions for use of PO lining products, positive pressure test and negative pressure test shall be taken separately or simultaneously. The nominal pressure and test pressure shall meet the requirements of GB 1048.6 Test methods6.1 Appearance Observe with the naked eye, in accordance with the provisions of 5.1. 6.2 Size measurement Measurements of length and thickness with qualified measuring instruments shall comply with the requirements of 5.4.5 and 5.5.1. 6.3 Electric spark detection The spark detection is carried out according to the regulations of HG/T 4090. 6.4 Pressure test 6.4.1 Shell test For the liquid test, the test pressure is 1.5 times the design pressure. After the dwell time is reached, the casing (before the lining) shall not leak or cause structural damage. About compress time, the piping is not less than 2 min, the equipment is not less than 30 min. 6.4.2 Seal test For the liquid test, the test pressure is 1. 1 times the design pressure. The test pressure shall remain unchanged during the holding and testing, no visible dripping. About compress time, the piping is not less than 2 min, the equipment is not less than 30 min. 7.2 Type inspection 7.2.1 Type inspection shall be performed in one of the following situations. a) trial model identification for new product; b) great changes in structure, material, technique after official production which may affect product performances; c) once of every two years in normal production; d) production resumed after long-term discontinued production; e) required by national quality supervision organization. 7.2.2 Sample for type inspection shall be randomly selected from the products that have passed the exit-factory inspection items. The number of samples is 3. The items for type inspection are all items except sub-clause 6.8 in Clause 6.8 Marks, packaging, transport, storage8.1 Marks There shall be obvious marks on the product. product name, nominal diameter (DN), nominal pressure (PN) and manufacturer trademark, etc. 8.2 Packaging It shall comply with the provisions of JB/T 4711. And protect the joint pipe and flange surface of the lining pipe and equipment to avoid damage. 8.3 Transport The product shall not be subjected to violent collision, throwing, or exposure during transport. 8.4 Storage Products shall be kept in a safe place and stored in a clean room. The stacking site shall be leveled, the stacking height shall not exceed 2m, and the stacking site shall be 1 m away from the heat source. Flange flanging surface protection material shall not be removed, damaged or peeled off when not installed. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of HG/T 4304-2012 be delivered?Answer: The full copy PDF of English version of HG/T 4304-2012 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of HG/T 4304-2012_English with my colleagues?Answer: Yes. The purchased PDF of HG/T 4304-2012_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- HG/T 4304-2012 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of HG/T 4304-2012?A step-by-step guide to download PDF of HG/T 4304-2012_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "HG/T 4304-2012". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
