GB/T 41155-2021 PDF EnglishUS$185.00 · In stock · Download in 9 seconds
GB/T 41155-2021: Sintered metal materials, excluding hardmetals - Fatigue test pieces Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 41155-2021: Sintered metal materials, excluding hardmetals - Fatigue test pieces---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT41155-2021NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.160 CCS H 21 GB/T 41155-2021 / ISO 3928:2016 Sintered metal materials, excluding hardmetals - Fatigue test pieces (ISO 3928:2016, IDT) ISSUED ON: DECEMBER 31, 2021 IMPLEMENTED ON: JULY 01, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions... 4 4 Pressed and sintered specimens for reverse bending and axial fatigue testing ... 4 5 Provisions on dies ... 5 6 Machined specimens ... 7 7 Identification of specimens ... 9 Appendix A (Informative) Supplementary instructions ... 10 References ... 11 Sintered metal materials, excluding hardmetals - Fatigue test pieces1 ScopeThis document specifies the dimensions of the die cavity, which his used for the preparation of fatigue specimens, by pressing and sintering, the dimensions of the specimens, which are prepared using this die, the dimensions of the specimens, which are machined by sintering and powder forging materials. This document applies to all sintered metals and alloys (excluding hardmetals).2 Normative referencesThere are no normative references in this document.3 Terms and definitionsThere are no terms and definitions, that need to be defined, in this document.4 Pressed and sintered specimens for reverse bending andaxial fatigue testing 4.1 General The specimens, which are prepared by pressing and sintering, can be further processed, such as dimensional finishing, polishing or heat treatment. If these treatments are taken, they shall be noted in the test report. In the metallographic examination of the specimen section, there shall be no micro-cracks, which have a length exceeding 0.25 mm in the test area. The pressing die shall be kept in good condition, to avoid burrs. The corners of the test area of the sintered specimen shall be ground, to remove burrs generated during the pressing process. 4.2 Requirements for unnotched specimens The unnotched specimen is as shown in Figure 2a). Flatness and parallelism shall be 0.1 mm. Other dimensions are recommended values. 4.3 Requirements for notched specimensAppendix A(Informative) Supplementary instructions ISO 1099, ISO 1352, ISO 1143 defines general principles for metal fatigue test specimens, which apply to the following sintered metals. a) Sintered metals are characterized by porosity, which inevitably leads to stress concentrations. b) Pores reduce the actual cross-sectional area of the specimen to be tested, which means that the theoretical stress value calculated according to the formula is smaller than the actual stress value. c) In most cases, sintered specimens with connected pores on the surface are more sensitive to the environment than dense materials. Porous products are not only affected by internal erosion, during fatigue testing, but also before testing; therefore, such specimens need to be stored with more care than dense material specimens. d) The surface state of the specimen or powder metallurgy part will significantly affect its fatigue performance, so in order to obtain suitable fatigue data from the fatigue specimen, to evaluate the fatigue performance of the powder metallurgy part, the surface state of the specimen and the part needs to be comparable. e) Milling or turning will cause surface densification and residual compressive stress, which will result in higher fatigue strength than that in the non-machined state (the grinding operation is gentler). Therefore, the surface of the specimen shall be machined, only if the critical parts of the powder metallurgy part are also machined. However, since most powder metallurgy parts have non-machined surfaces, the assessment of fatigue properties is best done, through the fatigue data obtained from non-machined surfaces. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 41155-2021 be delivered?Answer: The full copy PDF of English version of GB/T 41155-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 41155-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 41155-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 41155-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 41155-2021?A step-by-step guide to download PDF of GB/T 41155-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 41155-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
