GB/T 41079.1-2021 PDF EnglishUS$125.00 · In stock · Download in 9 seconds
GB/T 41079.1-2021: Test methods for physical properties of liquid metals - Part 1: Determination of density Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 41079.1-2021: Test methods for physical properties of liquid metals - Part 1: Determination of density---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT41079.1-2021 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.040.99 CCS H 21 Test methods for physical properties of liquid metals -- Part 1.Determination of density Issued on: DECEMBER 31, 2021 Implemented on: JULY 1, 2022 Issued by. State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword... 3 Introduction... 4 1 Scope... 6 2 Normative references... 6 3 Terms and Definitions... 6 4 Principles... 6 5 Instruments and equipment... 7 6 Samples... 8 7 Test steps... 8 8 Test data processing... 9 9 Precision... 9 10 Test report... 10 Test methods for physical properties of liquid metals Part 1.Determination of density1 ScopeThis document specifies a method for the determination of liquid metal density. This document applies to the determination of liquid metal density in the range of room temperature to 300 °C. It can also be used as a reference to the density measurement of molten salt and metal melt above 300 °C.2 Normative referencesThe following documents contain the provisions which, through normative reference in this document, constitute the essential provisions of this document. For the dated referenced documents, only the versions with the indicated dates are applicable to this document; for the undated referenced documents, only the latest version (including all the amendments) is applicable to this document. GB/T 1423 Method of measurement of density for precious metals and their alloys GB/T 4339 Test methods for thermal expansion characteristic parameters of metallic materials GB/T 8170 Rules of rounding off for numerical values & expression and judgment of limiting values3 Terms and DefinitionsThere are no terms and definitions that need to be defined in this document.4 PrinciplesOn the basis of Archimedes’ principle, measure the mass of a heavy hammer with known mass after it is immersed in liquid metal, and obtain the buoyancy of the heavy hammer to calculate the density of the liquid metal. The schematic diagram is shown in Figure 1.6 Samples6.1 Liquid sample. The volume shall be not less than 50 mL, and it can completely immerse the heavy hammer. The surface oxide layer shall be removed before testing. 6.2 Solid sample. It shall be made into particles or small pieces of solid that are easy to be loaded; the volume of the sample after melting shall be not less than 50 mL, and it can completely immerse the heavy hammer.7 Test steps7.1 Parallel test Two measurements shall be performed independently and the average value is taken as the result. 7.2 Determination 7.2.1 Determine the density ρ0 of the heavy hammer at room temperature according to the method described in GB/T 1423.If necessary, determine the linear thermal expansion coefficient of the heavy hammer’s material according to the method described in GB/T 4339. 7.2.2 Put the sample into the crucible, place the temperature measuring thermocouple in the sample, and place the crucible in the furnace. 7.2.3 Hang the heavy hammer on the electronic balance with a suspension wire and place it just above the sample. 7.2.4 Infuse inert gas with a flow rate of 0.1 L/min~1 L/min into the furnace cavity for at least 30 min to exhaust the air in the furnace cavity; keep the inert gas flow rate at 0.1 L/min~0.2 L/min during the test. 7.2.5 Heat the sample to the test temperature and keep it at the temperature constantly for at least 30 min. 7.2.6 Measure the weighed mass m0 of the heavy hammer in inert gas. 7.2.7 Make the heavy hammer completely immersed in the sample, and the heavy hammer shall not be in contact with the bottom or wall of the crucible. 7.2.8 After the balance reading is stable, record the weighed mass m1 of the heavy hammer in the sample. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 41079.1-2021 be delivered?Answer: The full copy PDF of English version of GB/T 41079.1-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 41079.1-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 41079.1-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 41079.1-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 41079.1-2021?A step-by-step guide to download PDF of GB/T 41079.1-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 41079.1-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
