GB/T 40388-2021 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 40388-2021: Test method for shear strength of C/C composites Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 40388-2021: Test method for shear strength of C/C composites---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40388-2021GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.120 CCS Q 23 Test method for shear strength of C/C composites ISSUED ON: AUGUST 20, 2021 IMPLEMENTED ON: MARCH 01, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Method principle ... 5 5 Test equipment ... 5 6 Test pieces ... 5 7 Test conditions ... 7 8 Test procedures ... 7 9 Calculation ... 8 10 Test report ... 9 Appendix A (Informative) Diagram of shearing fixture and main components ... 10 Test method for shear strength of C/C composites1 ScopeThis document specifies the method principle, test equipment, test pieces, test conditions, test procedures, calculations and test report of the test method for shear strength of C/C composites at room temperature. This document applies to the determination of the shear strength of C/C composites by the method of punching and shearing.2 Normative referencesThe following documents are normatively referenced in this document and are indispensable for its application. For dated references, only the version corresponding to that date is applicable to this document; for undated references, the latest version (including all amendments) is applicable to this document. GB/T 1446, Fiber-reinforced plastics composites - The generals GB/T 33501-2017, Test method for tensile property of C/C composites3 Terms and definitionsTerms and definitions determined by GB/T 33501-2017 are applicable to this document. 3.1 C/C composites Carbon fiber-reinforced carbon matrix composites. [Source: GB/T 33501-2017, 3.1] 3.2 The XY direction Direction of no weft or continuous long fiber tiling planes in C/C composites (3.1). [Source: GB/T 33501-2017, 3.6] 3.3 The Z direction Direction vertical to the XY direction (3.2) in the C/C composites (3.1). [Source: GB/T 33501-2017, 3.7] Valid samples in each group shall be no less than 5.7 Test conditions7.1 Test environment The test environment shall meet the laboratory standard environment specified in GB/T 1446. 7.2 Sample state adjustment Before the test, the sample shall be placed at least 24 h under the condition of laboratory standard environment.8 Test procedures8.1 Check the appearance of the sample according to the provisions of GB/T 1446; check the number and direction of each sample. 8.2 Adjust the state of the sample according to the provisions of 7.2. 8.3 After the sample state adjustment, measure the sample thickness h at four positions in the direction of 90° to each other, at the diameter of 25 mm of the sample, accurate to 0.01 mm; take the arithmetic mean of the four measurement results. Measure the diameter d at any two positions of the inner ring clamping block on the fixture, accurate to 0.02 mm; take the arithmetic mean of the two measurement results. The schematic diagram of the shearing fixture assembly is shown in Figure 3. 8.4 Fix the pin shaft on the force acting platform; respectively insert the upper inner ring clamping block, upper outer ring, sample and lower inner ring clamping block into the pin shaft in sequence; use the gasket and the sample clamping nut to fasten the sample in the upper and lower inner ring clamping blocks. The tightening torque is 1 N·m [see Figure 3a)]. 8.5 Put the combination of the upper and lower inner ring clamping blocks of the sample into the lower outer ring of the test fixture, where the upper outer ring is connected to the lower outer ring through the clamp screw [see Figure 3b)], and the tightening torque of the screw is 1 N·m. The sample installation is then completed [see Figure 3c)]. 8.6 Center the test fixture on the compression platform of the testing machine; continuously apply a compressive load to the sample at a loading rate of 2 mm/min until the sample fails or the load drops to 30% of the maximum load; continuously measure the load-displacement data; record the maximum load. Pmax – maximum load before failure, in Newtons (N); d – diameter of the upper inner ring clamping block of the fixture, in millimeters (mm); h – sample thickness, in millimeters (mm). 9.2 Calculate the arithmetic mean, standard deviation and dispersion coefficient according to GB/T 1446.10 Test reportThe test report generally includes the following contents: a) name of the test item and number of this document; b) test time, place and test environmental conditions; c) sample source, material variety and specification; d) sample number, size, sample direction and quantity; e) types and specifications of test equipment and instruments; f) loading rate; g) load-displacement curve for each sample; h) the measured value of each sample, the mean, standard deviation and dispersion coefficient of each group of samples; i) test personnel, date and others. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 40388-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40388-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 40388-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40388-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40388-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 40388-2021?A step-by-step guide to download PDF of GB/T 40388-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 40388-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
