GB/T 33785-2017 PDF EnglishUS$140.00 · In stock · Download in 9 seconds
GB/T 33785-2017: Specification for high radiative coating energy-saving technology Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 33785-2017: Specification for high radiative coating energy-saving technology---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33785-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77-010 H 04 Specification for High Radiative Coating Energy-Saving Technology Issued on: MAY 31, 2017 Implemented on: FEBRUARY 1, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. 3. No action is required - Full-copy of this standard will be automatically & immediately delivered to your EMAIL address in 0~60 minutes. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Terms and Definitions ... 4 4 Principle ... 5 5 Applicable Conditions ... 5 6 Technical Requirements ... 6 7 Energy-Saving Indicator ... 8 8 Effect Assessment ... 9ForewordThis Standard was drafted as per the rules specified in GB/T 1.1-2009. This Standard was proposed by China Iron and Steel Industry Association. This Standard shall be under the jurisdiction of National Technical Committee for Standardization of Steel (SAC/TC 183). Drafting organizations of this Standard. Shandong Huimin Science & Technology Co., Ltd., and China Metallurgical Information and Standardization Institute. Chief drafting staffs of this Standard. Zhou Huimin, Zhang Shaoqiang, Wang Jiangwei, Qiu Jinhui, Liu Changfu, Di Yanfei, Yang Xiuqing, Sun Chuansheng, and Liu Yizhou. Specification for High Radiative Coating Energy-Saving Technology1 ScopeThis Standard specifies the terms and definitions, principle, applicable conditions, technical requirements, energy-saving indicator and effect assessment of high radiative coating energy-saving technology. This Standard is applicable to the industrial furnaces in the metallurgical, coking, petrochemical, power, heat, and the like industries; other industries’ furnace can use this standard for reference.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. GB/T 31934 Measuring and Calculation Method for Heat Storage Capacity of High Radiative Coating GB/T 32287 Methods of Determination and Calculation of Heat Balance for Hot Blast Stove and Blast Furnace YB/T 134 Infrared Radiation Coatings at High Temperature YB/T 4313 Methods of Determination and Calculation of Heat Balance in Regenerative Furnace of Iron and Steel Industry3 Terms and DefinitionsThe following terms and definitions are applicable to this document. 3.1 High radiative coating energy-saving technology The energy-saving technology to improve the heat efficiency of furnace by the high radiative coating material through finely ground to a medium diameter of less than 20µm; is coated on the surface of base material through interface modified treatment; and forms the high-temperature-oxidation-resistant coating firmly combining with base. 3.2 High radiative coating material The materials composite made between the high emissivity powder and high temperature binder. 3.3 Heat storage capacity Under the setting temperature and specified time conditions, the heat absorbed by the heat-retainer.4 PrincipleWhen the high radiative coating material is coated on the corresponding part of the furnace, the surface emissivity of base material is improved; the radiative heat transferring between the base surface and gas under high temperature is strengthened; and energy efficiency of furnace is improved.5 Applicable Conditions5.1 Applicable principle The application of high radiative coating energy-saving technology shall satisfy the following conditions. a) The base surface shall be solid, hard to peel off, no glaze, no oil stains; b) Coating shall not contact liquid, solid materials or water vapor; c) Working temperature of coating shall be at 300°C~1700°C. 5.2 Applicable furnace 5.2.1 Common furnace The types and coating parts of the common furnace adopting high radiative coating energy-saving technology can refer to Table 1. Table 1 -- High Radiative Coating Energy-Saving Technology Applicable Furnace and Coating Parts Industries Furnace Types Coating Parts Metallurgy Blast furnace hot-blast stove Surface of heat-retainer in heat storage room Steel-rolling heating furnace Inner wall of furnace, surface of heat-retainer Coking Coke oven Inner wall of vertical flue, surface of heat-retainer in heat 4 Petrochemical Tube heating furnace 2.0 Entire inner wall of radiative room, outer surface of furnace tube 5 Power, heat Boiler 2.0 Entire inner wall of radiative room, outer surface of wall-cooling wall tube8 Effect Assessment8.1 Test of heat storage capacity It shall be tested as per GB/T 31934. 8.2 Test of energy-saving effect a) Compared the furnace adopting high radiative coating energy-saving technology with the furnace not adopting high radiative coating energy-saving technology but has the same furnace type, the same working condition. b) The heat balance test of blast furnace hot-blast stove shall be implemented as per the provisions of GB/T 32287; other furnaces shall refer to GB/T 32287 and YB/T 4313 to test. c) The energy-saving effect of high radiative coating energy-saving technology shall be calculated as per Formula (1). Where. η – energy-saving rate of high radiative coating energy-saving technology; Bw – fuel consumption per unit production of the furnace not adopting high radiative coating energy-saving technology, in m3/m3, or m3/t, or t/t; Bt – fuel consumption per unit production of the furnace adopting high radiative coating energy-saving technology, in m3/m3, or m3/t, or t/t; NOTE. when furnace product and fuel are both gas, the unit is m3/m3; when furnace product is solid or liquid, while fuel is gas, the unit is m3/t; when furnace product is solid or liquid, while fuel is solid or liquid, the unit is t/t. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 33785-2017 be delivered?Answer: The full copy PDF of English version of GB/T 33785-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 33785-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33785-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33785-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 33785-2017?A step-by-step guide to download PDF of GB/T 33785-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 33785-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
