GB/T 3098.13-1996 PDF EnglishUS$100.00 · In stock · Download in 9 seconds
GB/T 3098.13-1996: Mechanical properties of fasteners. Torsional test and minimum torques for bolts and screws with nominal diameters from 1mm to 10mm Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Similar standardsGB/T 3098.13-1996: Mechanical properties of fasteners. Torsional test and minimum torques for bolts and screws with nominal diameters from 1mm to 10mm---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3098.13-1996 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 公称直径 1 ~ 10 mm (IDT ISO898-7:1992) APPROVED ON: DECEMBER 18, 1996 IMPLEMENTED ON: JULY 01, 1997 Approved by: State Bureau of Technical Supervision Table of ContentsForeword ... 3 ISO Foreword ... 5 1 Scope ... 6 2 Normative references ... 6 3 Torque test ... 6 4 Minimum breaking torque ... 7 Appendix A (Informative) Comment ... 9ForewordThis standard is equivalent to the international standard ISO 898-7:1992 "Mechanical properties of fasteners - Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm". The general title of GB 3098 is "Mechanical properties of fasteners", including the following parts: - GB 3098.1-82 Mechanical properties of fasteners - Bolts, screws and studs - GB 3098.2-82 Mechanical properties of fasteners - Nuts - Coarse thread - GB 3098.3-82 Mechanical properties of fasteners - Set screws - GB 3098.4-86 Mechanical properties of fasteners - Nuts with fine pitch thread - GB 3098.5-85 Mechanical properties of fasteners - Tapping screws - GB 3098.6-86 Mechanical properties of fasteners - Stainless steel bolts, screws and studs - GB 3098.7-86 Mechanical properties of fasteners - Thread rolling screws -GB/T 3098.8-92 Mechanical properties of fasteners - Components for belted connections made mainly from materials with a high temperature strength -GB/T 3098.9-93 Mechanical properties of fasteners - Prevailing torque type steel hexagon nuts -GB/T 3098.10-93 Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals - GB/T 3098.11-1995 Mechanical properties of fasteners - Self-drilling tapping screws - GB/T 3098.12-1996 Mechanical properties of fasteners - Cone proof load test on nuts - GB/T 3098.13-1996 Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10 mm Appendix A of this standard is an informative appendix. This standard was proposed by the Ministry of Machinery Industry of the People's Republic of China.ISO ForewordISO (International Organization for Standardization) is a worldwide association of national standards bodies (ISO member bodies). The formulation of international standards is carried out through ISO technical committees. If each member group is interested in a project carried out by a certain technical committee, they can also participate in the committee. Governmental and non- governmental international organizations related to iso can also participate in this work. ISO has a close relationship with the International Electrotechnical Commission (IEC) in terms of electrical standardization. The draft international standard adopted by the technical committee is distributed to all member groups for voting. The official publication of international standards requires at least 75% of the member groups to vote for it. The international standard ISO 898-7 was formulated by the ISO/TC2 Fastener Technical Committee and the SC1 Fastener Mechanical Performance Subcommittee. The general title of ISO 898 is "Mechanical properties of fasteners" and includes the following parts: - Part 1: Bolts, screws and studs - Part 2: Coarse thread of nut with specified guaranteed load value - Part 5: Set screws and similar threaded fasteners not subject to tensile stress - Part 6: Nuts with specified guaranteed load value - Fine thread - Part 7: Torque test and minimum torque of bolts and screws with nominal diameter 1 ~ 10 mm Appendix A is an informative appendix. Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm1 ScopeThis standard specifies the torque test and breaking torque values of bolts and screws with a nominal diameter of 1 ~ 10 mm and a performance level of 8.8 ~ 12.9 (GB 3098.1). This standard applies to bolts and screws whose thread size is smaller than M3 and the minimum tensile load and guaranteed load are not specified in GB 3098.1, as well as the bolts and screws with a nominal diameter of 3 ~ 10 mm whose length is too short to carry out the tensile test. The breaking torque does not apply to hexagon socket set screws.2 Normative referencesThe clauses contained in the following standards constitute the clauses of this standard by being quoted in this standard. At the time of publication, the editions indicated were valid. All standards will be revised; all parties using this standard shall study the possibility of using the latest version of the following standard. GB 3098.1-82 Mechanical properties of fasteners - Bolts, screws and studs3 Torque test3.1 Principle Clamp the tested bolt or screw in the test device and measure its breaking torque. 3.2 Device (instrument) 3.2.1 Torque test device, as shown in Figure 1. 3.2.2 The indicated value of the torque meter shall not exceed five times the ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3098.13-1996 be delivered?Answer: The full copy PDF of English version of GB/T 3098.13-1996 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3098.13-1996_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3098.13-1996_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3098.13-1996 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 3098.13-1996?A step-by-step guide to download PDF of GB/T 3098.13-1996_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3098.13-1996". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
