GB/T 3098.6-2023 PDF EnglishUS$650.00 · In stock · Download in 9 seconds
GB/T 3098.6-2023: Mechanical properties of fasteners - Stainless steel bolts, screws and studs Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3098.6: Historical versions
Similar standardsGB/T 3098.6-2023: Mechanical properties of fasteners - Stainless steel bolts, screws and studs---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3098.6-2023GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 21.060.10 CCS J 13 Replacing GB/T 3098.6-2014 Mechanical properties of fasteners - Stainless steel bolts, screws and studs (ISO 3506-1.2020, Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1.Bolts, screws and studs with specified grades and performance classes, MOD) Issued on. MAY 23, 2023 Implemented on. DECEMBER 01, 2023 Issued by. State Administration for Market Regulation; National Standardization Administration. Table of ContentsForeword... 4 Introduction... 8 1 Scope... 11 2 Normative references... 12 3 Terms and definitions... 13 4 Symbols... 14 5 Stainless steel group and performance grade marking system... 16 5.1 General... 16 5.2 Stainless steel group marking (part 1)... 17 5.3 Marking of performance grade (part 2)... 17 6 Materials... 18 6.1 Chemical composition... 18 6.2 Heat treatment of martensitic stainless steel fasteners... 21 6.3 Surface finishing... 21 6.4 Corrosion resistance... 21 7 Mechanical and physical properties... 22 8 Applicability of test methods and inspections... 28 8.1 Applicability of test methods... 28 8.2 Load-bearing capacity of fasteners... 28 8.3 Manufacturer's inspection... 30 8.4 Supplier inspection... 30 8.5 Buyer inspection... 31 8.6 Delivery of test results... 31 9 Test method... 31 9.1 Tensile test... 31 9.2 Tensile test of bolts and screws with reduced load capacity due to head design... 39 9.3 Tensile test of bolts, screws, studs with reduced load capacity due to shank design. 40 9.4 Wedge load test... 41 9.5 Torque test... 43 9.6 Hardness test... 45 10 Marking and labeling of fasteners... 46 10.1 Marking... 46 10.2 Manufacturer's identification mark... 48 10.3 Fastener marking... 48 10.4 Packaging marking (label)... 52 Appendix A (Informative) Mechanical properties at high temperatures and application at low temperatures... 54 References... 56ForewordThis document was drafted in accordance with the provisions of GB/T 1.1-2020 "Directives for standardization - Part 1.Rules for the structure and drafting of standardizing documents". This document is Part 6 of GB/T 3098 "Mechanical properties of fasteners". GB/T 3098 has published the following parts. - GB/T 3098.1 Mechanical properties of fasteners - Bolts, screws and studs; - GB/T 3098.2 Mechanical properties of fasteners - Nuts; - GB/T 3098.3 Mechanical properties of fasteners - Set screws; - GB/T 3098.5 Mechanical properties of fasteners - Tapping screws; - GB/T 3098.6 Mechanical properties of fasteners - Stainless steel bolts, screws and studs; - GB/T 3098.7 Mechanical properties of fasteners - Thread rolling screws; - GB/T 3098.8 Mechanical properties of fasteners - Parts for bolted connections for use at temperatures from-200 °C ~ +700 °C - GB/T 3098.9 Mechanical properties of fasteners - Prevailing torque type steel nuts; - GB/T 3098.10 Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals; - GB/T 3098.11 Mechanical properties of fasteners - Drilling screws with taping screw thread; - GB/T 3098.12 Mechanical properties of fasteners - Cone proof load test on nuts; - GB/T 3098.13 Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm; - GB/T 3098.14 Mechanical properties of fasteners - Widening test on nuts; - GB/T 3098.15 Mechanical properties of fasteners - Stainless steel nuts; - GB/T 3098.16 Mechanical properties of fasteners - Stainless steel set screws; - GB/T 3098.17 Mechanical properties of fasteners - Preloading test for the detection of hydrogen embrittlement-Parallel bearing surface method; - GB/T 3098.18 Mechanical properties of fasteners - Blind rivets testing; - GB/T 3098.19 Mechanical properties of fasteners - Blind rivets with break pull mandrel; - GB/T 3098.20 Mechanical properties of fasteners - Wing nuts with specified proof torque; - GB/T 3098.21 Mechanical properties of fasteners - Stainless steel tapping screws; - GB/T 3098.22 Mechanical properties of fasteners made of the fine grain non-heat treatment steel - Bolts, screws and studs; - GB/T 3098.23 Mechanical properties of fasteners - M42 ~ M72 bolts, screws and studs; - GB/T 3098.24 Mechanical properties of fasteners - Stainless steel and nickel alloys bolts, screws, studs and nuts for high temperature applications; - GB/T 3098.25 Mechanical properties of fasteners - Guidance for the selection of stainless steels and nickel alloys for fasteners; - GB/T 3098.26 Mechanical properties of fasteners - Flat washers. This document replaces GB/T 3098.6-2014 "Mechanical properties of fasteners - Stainless steel bolts, screws and studs". Compared with GB/T 3098.6-2014, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) ADD duplex (austenite-ferrite) stainless steel with performance grades of 70, 80, 100 (see Figure 1); b) ADD the austenitic stainless steel performance grade 100 and group A8 (see Figure 1); c) CHANGE the surface finishing (see 6.3; Chapter 4 of the 2014 edition); d) ADD the stainless steel bolt and nut group matching (see 6.4); e) ADD the minimum tensile load and minimum load calculation value when the specified plastic elongation is 0.2%, as well as the principle of numerical rounding (see Table 4 ~ Table 7); f) ADD the fasteners with reduced bearing capacity due to head structure or rod structure (see 8.2); g) ADD the inspection procedure requirements and guidance (see 8.3 ~ 8.6); h) ADD the applicability of full load capacity and reduced load capacity test methods (see Chapter 8); i) CHANGE the tensile strength test procedure (see 9.1; 7.2 of the 2014 edition); ADD reduced load capacity test method (see 9.2 and 9.3); j) CHANGE the wedge load test (see 9.4; 7.2 of the 2014 edition) and hardness test (see 9.6; 7.2 of the 2014 edition); k) CHANGE the marking and labeling; ADD the reduced load capacity fastener marking method (see Chapter 10; Chapter 4 of the 2014 edition); l) CHANGE the mechanical properties at high temperature and application at low temperature (see Appendix A; Appendix F of the 2014 edition); m) DELETE the common appendixes in the series of mechanical properties standards for stainless steel fasteners (see Appendix B ~ Appendix E; Appendix G, Appendix H of the 2014 edition). This document modifies and adopts ISO 3506-1.2020 "Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1.Bolts, screws and studs with specified grades and performance grades". The technical differences between this document and ISO 3506-1.2020, as well as their reasons, are as follows. - USE the normative reference GB/T 3098.25 to replace ISO 3506-6, to adapt to China's technical conditions (see 6.1); - USE the normative reference GB/T 39310 to replace ISO 16228, to adapt to China's technical conditions (see 8.6); - USE the normative reference GB/T 16825.1 to replace ISO 7500-1, to adapt to China's technical conditions (see 9.1.1); - USE the normative reference GB/T 228.1 to replace ISO 6892-1, to adapt to China's technical conditions (see 9.1.1, 9.1.2, 9.4.2); - USE the normative reference GB/T 12160 to replace ISO 9513, to adapt to China's technical conditions (see 9.1.3); - USE the normative reference GB/T 230.1 to replace ISO 6508-1, to adapt to China's technical conditions (see 9.6.2); - USE the normative reference GB/T 231.1 to replace ISO 6506-1, to adapt to China's technical conditions (see 9.6.2); - USE the normative reference GB/T 4340.1 to replace ISO 6507-1, to adapt to China's technical conditions (see 9.6.2); - USE the normative reference GB/T 3099.4 to replace ISO 1891-4, to adapt to China's technical conditions (see 10.4); - DELETE the "soft" state of austenitic stainless steel performance grade 70 fasteners, to conform to the actual state of austenitic stainless steel fasteners (see Figure 1). The following editorial changes have been made to this document. - CHANGE the name of the standard to "Mechanical properties of fasteners - Stainless steel bolts, screws and studs"; - USE the Chinese document to replace the international documents of informative reference; - CHANGE that "Stainless steel group marking (Part 1) consists of one letter..." into that. "Stainless steel group marking (Part 1) consists of one letter and one number..." (see 5.2). Please note that some contents of this document may involve patents. The issuing agency of this document does not assume the responsibility for identifying patents. This document was proposed by the China Machinery Industry Federation. This document shall be under the jurisdiction of the National Technical Committee for Standardization of Fasteners (SAC/TC 85). Drafting organizations of this document. China Machinery Productivity Promotion Center Co., Ltd., Hebei Wuwei Avionics Technology Co., Ltd., Shanghai Jiyoubiaowu High Strength Fastener Co., Ltd., Zhoushan 7412 Factory, Wuxi Standard Parts Factory Co., Ltd., Suzhou Thermal Engineering Research Institute Co., Ltd., Hunan Shenyi Machinery Application Research Institute Co., Ltd., Machinery Industry General Parts Product Quality Supervision and Inspection Center, Zhejiang Ancheng Metal Products Co., Ltd., Shandong Lugui Fastener Co., Ltd. This document is interpreted by the National Technical Committee for Standardization of Fasteners. This standard replaces the standard previously issued as follows. - This document was first published in 1986.It was revised for the first time in 2000. It was revised for the second time in 2014; - This is the third revision.1 ScopeThis document specifies the mechanical and physical properties of coarse and fine thread bolts, screws and studs (hereinafter referred to as fasteners) made of corrosion- resistant stainless steel, when tested at an ambient temperature of 10 °C ~ 35 °C. The performance grades corresponding to the groups of austenitic, martensitic, ferritic, duplex (austenitic-ferritic) stainless steel fasteners are specified.2 Normative referencesThe contents of the following documents constitute the essential terms of this document through normative references in the text. Among them, for dated references, only the version corresponding to that date applies to this document; for undated references, the latest version (including all amendments) applies to this document.3 Terms and definitionsThe following terms and definitions apply to this document. Steel which has stainless steel and corrosion resistance as main characteristics, a chromium (Cr) content of at least 10.5% (mass fraction) and carbon (C) content of no more than 1.2% (mass fraction).4 SymbolsThe following symbols apply to this document.5 Stainless steel group and performance grade marking systemThe marking of performance grade (part 2) consists of 2 ~ 3 digits corresponding to 1/10 of the minimum tensile strength of the fastener specified in Table 2 or Table 3.6 MaterialsUnless otherwise specified, fasteners that meet this document shall be cleaned and polished. To prevent corrosion, bolts, screws and studs should be used with nuts and washers of the same stainless steel group (e.g. A2 nuts and A2 bolts). Other combinations may be used (e.g. A4 nuts and D4 bolts), provided that.7 Mechanical and physical propertiesBolts, screws, studs of specified stainless steel groups and performance grades shall comply with all applicable requirements specified in Tables 2 ~ 8, when tested in accordance with the methods specified in Chapter 9, at ambient temperatures of 10 °C ~ 35 °C, either during the manufacturing process or at the time of final inspection of the finished product.8 Applicability of test methods and inspectionsStandardized or non-standardized, full-load-bearing capacity stainless steel bolts, screws or studs, when subjected to tension testing until fracture. The buyer may control and/or test the delivered fasteners according to the test methods specified in Chapter 9.9 Test methodThis test is used to determine the following parameters simultaneously or separately. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3098.6-2023 be delivered?Answer: The full copy PDF of English version of GB/T 3098.6-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3098.6-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3098.6-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3098.6-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3098.6-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3098.6-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3098.6-2023?A step-by-step guide to download PDF of GB/T 3098.6-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3098.6-2023". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
