GB/T 18431-2014 PDF EnglishUS$225.00 · In stock · Download in 9 seconds
GB/T 18431-2014: Steam and hot water type lithium bromide absorption water chiller Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 18431: Historical versions
Similar standardsGB/T 18431-2014: Steam and hot water type lithium bromide absorption water chiller---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT18431-2014NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.200 J 73 Replacing GB/T 18431-2001 Steam and Hot Water Type Lithium Bromide Absorption Water Chiller Issued on. JUNE 24, 2014 Implemented on. DECEMBER 21, 2014 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Normative References... 4 3 Terms and Definitions... 4 4 Types and Basic Parameters... 5 5 Requirements... 6 6 Test Methods... 8 7 Inspection Rules... 11 8 Marking, Packaging and Storage... 12 Appendix A (Normative) Test Methods for Refrigerating Capacity... 14 Appendix B (Normative) Calculation Method of Heat Loss Rate of Unit... 19 Appendix C (Normative) Determination Method of Pressure Loss... 21 Appendix D (Normative) Technical Requirements of Lithium Bromide Solution ... 23 Appendix E (Normative) Requirements for Cooling Water and Supplementary Water Quality... 24ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard replaces "Steam and Hot Water Type Lithium Bromide Absorption Water Chiller" (GB/T 18431-2001). This Standard contains the following main technical changes, compared with GB/T 18431-2001. - the inlet and outlet temperature of cold water under nominal condition were modified (see 4.3.1; 4.3.1 of 2001 edition); - the performance parameter (consumption of heat source in specific refrigerating effect) indexes under nominal condition were modified (see 4.3.1; 4.3.1 of 2001 edition); - the fouling coefficients of the unit at cold water side and cooling water side under nominal condition were modified [see 4.3.2 a); 4.3.2.1 of 2001 edition]. This Standard was proposed by the China Machinery Industry Federation. This Standard shall be under the jurisdiction of the National Technical Committee on Refrigeration & Air-Conditioning Equipment of Standardization Administration of China (SAC/TC 238). Chief drafting organizations of this Standard. Shuangliang Eco-energy Systems Co., Ltd., Hefei General Machinery Research Institute, Dalian Sanyo Refrigeration Co., Ltd, Hefei General Machinery Research Institute Co., Ltd., Hefei General Environmental Control Technology Co., Ltd. Chief drafting staffs of this Standard. Mao Hongcai, Liu Xiaoli, Wang Rujin, Cai Xiaorong, Mi Hua, Ding Yujuan. The previous edition of the standard superseded by this Standard is as follows. - GB/T 18431-2001. Steam and Hot Water Type Lithium Bromide Absorption Water Chiller1 ScopeThis Standard specifies the terms and definitions, types and basic parameters, requirements, test methods, inspection rules, marking, packaging and storage of steam and hot water type lithium bromide absorption water chiller (hereinafter referred to as "unit"). This Standard is applicable to steam and hot water single-effect and double-effect units for central air conditioning and technology.2 Normative ReferencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including all the amendments) applies. GB 151 Tubular Heat Exchangers GB/T 13306 Plates GB 18361 Safety Requirements of Lithium Bromide Absorption Water Chiller (Beater) GB/T 18430.1-2007 Water Chilling (Heat Pump) Packages Using the Vapor Compression Cycle - Part 1.Water Chilling (Heat Pump) Packages for Industrial & Commercial and Similar Application JB/T 4330-1999 Determination of Noise Emitted by Refrigerating and Air Conditioning Equipment3 Terms and DefinitionsFor the purposes of this document, the terms and definitions established in JB/T 7249 and the following ones apply. 3.1 Consumption of heat source The flow of steam and hot water consumed by the unit, in kg/h for steam unit and kg/h or m3/h for hot water unit. 3.2 Heat consumption of heat source The value of consumption of heat source converted to heat, in kW.4 Types and Basic Parameters4.1 Type 4.1.1 According to heat source, the unit is divided into. 4.1.2 According to refrigerating cycle, the unit is divided into. 4.2 Model The model compilation method of unit is determined by the manufacturer at discretion; however, the model shall include the type of heat source and the nominal refrigerating capacity. 4.3 Basic parameters5 Requirements5.1 General requirements The unit shall be manufactured according to the drawing and technical document (or the agreement between users and the manufacturer) approved according to established procedure. 5.2 Air tightness and hydraulic pressure test 5.2.1 Air tightness test The complete machine leak rate of the unit shall not be greater than 2.03×10-6 Paꞏm3/s. 5.3 Nominal condition performance 5.3.1 Refrigerating capacity The refrigerating capacity of the unit shall not be less than 95% of the nominal refrigerating capacity. 5.4 Variable working condition performance The unit shall be able to work normally within the range specified in Table 2, and shall be subjected to variable working condition performance test according to interval value. 5.5 Partial load performance 5.5.1 The unit shall determine the possible minimum ability point by making determination on more than two points. 5.5.2 Determination of partial load performance shall meet the following requirements. 5.6 Noise The noise pressure level of unit shall not be greater than the indicated value. 5.7 Safety requirements The safety requirements of unit shall meet the requirements of GB 18361.6 Test Methods6.1 Measuring instrument The type and accuracy of measuring instrument shall meet those specified in Table 3, pass the calibration and be used within the period of validity. 6.2.2 Performance test under nominal condition 6.2.2.1 Refrigerating capacity Test shall be carried out according to Appendix A under the nominal condition specified in 4.3. 6.2.2.4 Water-side pressure loss The unit operates under nominal condition; after the determination of refrigerating capacity becomes stable, the pressure loss of unit at cold water side and cooling water side shall be determined according to Appendix C. 6.2.3 Test under variable working conditions The unit is subjected to test under variable working conditions by changing certain parameter separately according to the application scope and interval value specified in Table 2 with other conditions kept as those under the nominal condition; the test results shall be plotted into curve or compiled into table. 6.2.5 Noise test The unit operates under nominal condition and is subjected to noise measurement according to the method of rectangular hexahedron measurement surface in JB/T 4330-1999 and sound pressure level calculation according to surface average sound pressure level specified in JB/T 4330-1999. 6.2.6 Safety performance test Safety performance test shall be carried out according to the requirements of GB 18361.7 Inspection Rules7.1 Inspection item The unit inspection is divided into delivery inspection and type inspection. 7.2 Delivery inspection Each unit shall be subjected to delivery inspection and the inspection items and test methods shall be in accordance with those specified in Table 4.8 Marking, Packaging and Storage8.1 Marking 8.1.1 Permanent nameplate shall be set at the obvious position of each unit; the nameplate shall meet the requirements of GB/T 13306 and its contents shall include. 8.1.2 Delivery document Each unit shall be accompanied with the following documents. 8.2 Packaging The exposed uncoating surface of unit shall be taken with anti-rust measures; the screwed joint shall be blocked with screw plug and the flange hole shall be covered with blind-plate. 8.3 Storage 8.3.1 Before leaving factory, the unit shall be filled with 0.01MPa to 0.03MPa dry nitrogen or keep vacuum. 8.3.2 The unit shall be stored in warehouse or the place having cover. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 18431-2014 be delivered?Answer: The full copy PDF of English version of GB/T 18431-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 18431-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18431-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 18431-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 18431-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18431-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 18431-2014?A step-by-step guide to download PDF of GB/T 18431-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 18431-2014". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
