GB/T 10357.6-2013 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 10357.6-2013: Test of mechanical properties of furniture -- Part 6: Strength and durability of beds Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 10357.6: Historical versions
Similar standardsGB/T 10357.6-2013: Test of mechanical properties of furniture -- Part 6: Strength and durability of beds---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT10357.6-2013 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.140 Y 80 Replacing GB/T 10357.6-1992 Test of Mechanical Properties of Furniture - Part 6.Strength and Durability of Beds Issued on. OCTOBER 10, 2013 Implemented on. MAY 1, 2014 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 General Test Conditions... 5 3 Test Facilities... 6 4 Test Items and Procedures... 10 5 Evaluation of Test Results... 17Foreword"Test of Mechanical Properties of Furniture" (GB/T 10357) is divided into 8 parts. - Part 1.Strength and Durability of Tables; - Part 2.Stability of Chairs and Stools; - Part 3.Strength and Durability of Chairs and Stools; - Part 4.Stability of Storage Units; - Part 5.Strength and Durability of Storage Units; - Part 6.Strength and Durability of Beds; - Part 7.Stability of Tables; - Part 8.Stability of Chairs with Tilting or Reclining Mechanisms when Fully Reclined, and Rocking Chairs. This is Part 6 of GB/T 10357. This part is drafted in accordance with the rules given in GB/T 1.1-2009. This part supersedes "Test of Mechanical Properties of Furniture - Strength and Durability of Beds" (GB/T 10357.6-1992). Compared with GB/T 10357.6-1992, the main technical changes in this part are as follows. - Pretreatment is added; - Loading requirements are added; - Precision is added; - Test equipment requirements are added; - Test procedures are added; - Size of loading pad of horizontal static load for bed end structure is modified. Attention shall be drawn to the possibility that some of the elements of this document may involve patent rights. The issuance organization of this document shall not undertake the responsibility of identifying these patents. This part is proposed by China National Light Industry Council. This part is under the jurisdiction of National Technical Committee on Furniture of Standardization Administration of China (SAC/TC 480). Drafting organizations of this part. Guangdong Landbond Furniture Group Co., Ltd., Shanghai Institute of Quality Inspection and Technical Research (China National Furniture Quality Supervision Testing Center), Hunan Stardom Home Furnishing Development Co., Ltd. and Zhejiang Furniture and Hardware Research Institute. Chief drafting staff of this part. Wang Jin, Zhou Shanlin, Zhang Yinghong, Chen Huaxiang, Gu Ming, Zhang Rong, Tu Zhong, Fan Hongwei, Xu Jianmin and Xiao Qixin. The previous edition of the standard superseded by this part is as follows. - GB/T 10357.6-1992. Test of Mechanical Properties of Furniture - Part 6.Strength and Durability of Beds1 ScopeThis part of GB/T 10357 specifies test methods for the strength and durability of beds. This part is applicable to various hard-surface beds used in households and hotels. Beds of other types may also be implemented by reference to this part according to their use functions.2 General Test Conditions2.1 Specimen Specimen shall be completely assembled deliverable finished product. Assembling shall be carried out according to the instructions provided along with the product by the manufacturer. Where there are several assembly methods, it shall be assembled and tested with the method which is most unfavorable to the mechanical property inspection and recorded in the inspection report. Where assembling structure is not provided, the assembly method shall be recorded in the inspection report. The connecting piece shall be fastened before the test. Unless specially requested in the manufacturer's instructions, the connecting piece shall not be refastened during the test. 2.2 Test environment Unless otherwise specified, the temperature of test environment is 15~25℃ while the relative humidity is 40%~70%. 2.3 Loading requirements During static load test, the force application speed shall be as slow as possible to ensure that the additional dynamic load is small enough to be neglected. Unless otherwise stated in the contract, each applied load shall be maintained for 10~30s. During impact test, the impact body shall be able to fall freely. 2.4 Precision Unless otherwise specified, the following measuring precisions shall be adopted.3 Test Facilities3.1 General requirements for test device Unless otherwise specified, any appropriate test device may be adopted for the test; the reason is that the test result only depends on whether the applied force is correct rather than the device itself. 3.2 Loading pad 3.2.1 50mm loading pad A rigid cylinder with diameter of 50mm, its bottom surface is flat and smooth, and its edge chamfer radius is 12mm (see Figure 1). 3.2.2 200mm loading pad A flat and square rigid object with side length of 200mm×200mm, its bottom surface is flat and smooth, and its chamfer radius of edge and lateral edge of bottom surface is 12mm (see Figure 2). 3.2.5 Impactor The impactor is composed of cylinder, helical compression spring and impact head. A compression spring is arranged between cylinder and impact head; where they are connected, the cylinder and impact head shall be able to move relatively along the axis. The mass of cylinder and relevant accessories (except spring) fixed on the cylinder is (17±0.1)kg; the mass of the whole impactor is (25±0.1)kg. The overall elastic coefficient of impactor is (6.9±1)N/mm, and the total static friction of the relatively movable part is 0.25~0.45N. The pre-compression of all helical compression springs is (1040±5)N, and its recompression capacity shall be greater than 60mm. 3.3 Chock block A device used to prevent specimen from sliding but not restricting its tipping. Its height shall not be greater than 12mm; where relatively high chock block is required by the product design, the minimum height of chock block is restricted to avoid the specimen movement. 3.4 Ground The ground of test position shall be level, smooth and rigid.4 Test Items and Procedures4.1 Uniformly distributed static load test for bed base Measure the ground clearance of the bed base center H10 and the bed breadth B before test. 4.3 Horizontal static load test for bed end structure 4.4 Static load test for long side of bed Measure the ground clearance of the long side midpoint of bed H30 before test. Where the long side midpoint of bed is supported, measure the ground clearance of the quartering point of the long side of bed. Trisect this long side; simultaneously vertically and downward apply 1500N force to each trisection point which is 20mm away from the edge for 10 times with 50mm loading pad, maintain each loading for 10s at least; the time interval between two loadings is not greater than 30s (see Figure 10). In mm 4.5 Structure durability test for bed Block the bed ward off with chock block to avoid bed movement during test. Arrange 1000N balancing load on the bed base center with 350mm loading pad. Take two points, A and B, which are 50mm away from the same long side, from two short sides of the bed base, and another two points, C and D, which are 50mm away from the same short side, from two long sides of the bed base (4 loading points in total). The height of loading point is the same with that of the bed base; where the bed base is movable, the loading height is the same as that of the side rail. 4.6 Impact load test for bed base The bed base shall be free from mattress and any covering. Respectively impact in the center and weakest point of the bed base for 10 times with impact height of 140mm above the bed base (referring to the vertical distance from the bottom surface of impactor to the tested bed base); the time interval between two impacts is not greater than 30s. Balancing load5 Evaluation of Test ResultsThe test result is only valid for specimen; where the specimen is representative among similar products, the test result may represent the product performance of such type. Carry out inspection after each test and record all generated changes. The specimen, during or after each test, shall meet the following requirements. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 10357.6-2013 be delivered?Answer: The full copy PDF of English version of GB/T 10357.6-2013 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 10357.6-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 10357.6-2013_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 10357.6-2013 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 10357.6-2013?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 10357.6-2013 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 10357.6-2013?A step-by-step guide to download PDF of GB/T 10357.6-2013_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 10357.6-2013". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
