GB/T 39132-2020 PDF English
US$155.00 · In stock · Download in 9 secondsGB/T 39132-2020: Fuel cell electric vehicle engineering approval evaluation program Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 39132-2020 | English | 155 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Fuel cell electric vehicle engineering approval evaluation program
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 39132-2020
GB/T 39132-2020: Fuel cell electric vehicle engineering approval evaluation program---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT39132-2020
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.080.01
T 47
Fuel cell electric vehicle engineering approval
evaluation program
ISSUED ON: OCTOBER 11, 2020
IMPLEMENTED ON: MAY 01, 2021
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 5
4 Implementation conditions ... 5
5 Test items, test methods and judgment basis ... 6
6 Test procedures ... 8
7 Test report ... 8
Annex A (informative) Test method for driving range ... 10
Bibliography ... 12
Fuel cell electric vehicle engineering approval
evaluation program
1 Scope
This Standard specifies implementation conditions, test items, test methods,
judgment basis, test procedures and test report content for new product
engineering approval evaluation program of fuel cell electric vehicle.
This Standard is applicable to fuel cell electric vehicle that uses compressed
gaseous hydrogen.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
GB 1495, Limits and measurement methods for noise emitted by
accelerating motor vehicles
GB/T 12538, Road vehicles with two axles - Determination of centre of
gravity
GB/T 12673, Motor vehicle main dimensions measurement method
GB/T 12674, Motor vehicles - Weight parameter - Measuring method
GB/T 19750-2005, Hybrid electric vehicles - Engineering approval evaluation
program
GB/T 19752, Hybrid electric vehicle - Power performance - Test method
GB 20890-2007, Test Procedures and Requirement of Durability of Emission
Control Systems for Heavy-duty Vehicles
GB/T 24548, Fuel cell electric vehicles - Terminology
GB/T 24549, Fuel cell electric vehicles - Safety requirements
GB/T 26779, Fuel cell electric vehicles - Refueling receptacle
a) Major changes are required to meet the requirements of national standard
inspection items;
b) The effectiveness of steering and braking systems cannot ensure driving
safety;
c) There is a big gap between test vehicle performance indicators and
product technical conditions;
d) The frame, body and its load-bearing system are broken or cracked, and
the test cannot be carried out;
e) The fuel cell system, battery system, motor and its control system, DC/DC
converter, on-board hydrogen system, on-board charging system have
serious problems or frequent problems that cannot be tested;
f) Other circumstances that the testing organization considers that the test
shall be terminated.
4.5 During the test, the operation shall be carried out according to the provisions
of the instruction manual. Maintenance shall be performed.
4.6 After the test is completed, the testing organization will provide a test report
according to the provisions of Clause 6 and Clause 7.
5 Test items, test methods and judgment basis
5.1 General rules
5.1.1 The test vehicle shall be subjected to three tests: compulsory national
standards and related regulations inspection, whole-vehicle performance test
and whole-vehicle reliability driving test.
5.1.2 The test items of the modified vehicles shall be determined according to
the specific changes. All items that change due to the modification shall be
tested (inspected).
5.2 Compulsory national standards and related regulations inspection
5.2.1 Overview
Vehicles shall meet the requirements of relevant mandatory national standards
and related regulations. See 5.2.2~5.2.4 for the three test methods of external
noise, hydrogenation port, and vehicle hydrogen system.
5.2.2 Test of external noise
a test site authorized by the state.
5.4.2 The total mileage of the reliability driving test is 15000km. Test in the
hybrid drive mode. For the vehicle of which the total mass is not greater than
3500kg, the mileage is allocated as follows: strengthened bad road -- 3000km,
flat road -- 2000km, high-speed runway -- 5000km, durable working condition -
- 5000km (in accordance with Annex B of GB/T 19750-2005). For the vehicle of
which the total mass is greater than 3500kg, the mileage is allocated as follows:
strengthened bad road -- 3000km, flat road -- 2000km, high-speed runway --
5000km, durable working condition -- 5000km (in accordance with Annex A of
GB 20890-2007).
5.4.3 The main assembly shall not have types 1, 2 failures during the test. After
the test, the insulation performance, hydrogen leakage and idling exhaust
emissions of the vehicle shall meet the requirements of GB/T 24549.
NOTE 1: Type 1 failure refers to a failure that has occurred or will have a destructive
situation, which leads to the loss of system functions and may cause personal danger or
the main assembly of the vehicle to be scrapped; it needs to take emergency stop and
issue warning measures. Type 2 failure refers to a failure that seriously degrades the
performance of the system or damages the main assembly and cannot continue to operate
but does not constitute a personal danger; it may take normal shutdown and issue warning
measures.
6 Test procedures
6.1 Receive and check the test sample vehicle. Register it.
6.2 Conduct run-in driving in accordance with the manufacturer's regulations.
6.3 Carry out the tests such as compulsory national standards and related
regulations inspection, whole-vehicle performance test, reliability driving test,
and whole-vehicle performance retest.
7 Test report
The test report shall contain the following information:
a) Task source;
b) Test purpose;
c) Basis for determining the test plan;
d) Main standards for test basis;
Annex A
(informative)
Test method for driving range
A.1 Test conditions
A.1.1 Conduct the indoor test at room temperature of 20°C~30°C.
A.1.2 The viscosity of lubricating oil for mechanical moving parts meets the
manufacturer's regulations.
A.1.3 Turn off the lighting, signal devices and auxiliary equipment on the vehicle,
unless these devices are required for testing and daytime operation of the
vehicle.
A.1.4 Except for driving purposes, all energy storage systems are charged to
the maximum value specified by the manufacturer (electricity, hydraulic
pressure, air pressure).
A.1.5 The test driver makes the fuel cell and power battery work at normal
operating temperature in accordance with the operating procedures
recommended by the vehicle manufacturer.
A.1.6 The test vehicle shall be run-in according to the manufacturer's
specifications. The running-in mileage is not less than 300km.
A.1.7 For M1 and N1 vehicles as well as M2 vehicles of which the total mass
does not exceed 3500kg, chassis dynamometer settings are carried out in
accordance with Annex CC of GB 18352.6-2016. For other types of vehicles,
chassis dynamometer settings are in accordance with Annex C of GB/T 27840-
2011. If the driving resistance curve is provided by the automobile manufacturer,
it shall provide a test report, calculation report or other relevant information.
They shall be determined by the inspection agency.
A.1.8 The pressure of the hydrogen storage system is the rated pressure
specified by the manufacturer. The temperature of the hydrogen storage system
is 10°C~20°C.
A.1.9 For fuel cell electric vehicle equipped with power batteries and driven by
power batteries, the SOC state of its power battery system is adjusted to
(50±10)%.
A.2 Test steps
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 39132-2020 be delivered?Answer: The full copy PDF of English version of GB/T 39132-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 39132-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 39132-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 39132-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 39132-2020?A step-by-step guide to download PDF of GB/T 39132-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 39132-2020".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|