Powered by Google www.ChineseStandard.net Database: 189760 (20 Apr 2024)

GB/T 20076-2021 (GBT20076-2021)

GB/T 20076-2021_English: PDF (GBT 20076-2021, GBT20076-2021)
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)StatusPDF
GB/T 20076-2021English305 Add to Cart 0--9 seconds. Auto-delivery Measurement methods of maximum torque and maximum net power of engines for motorcycles and mopeds Valid GB/T 20076-2021

BASIC DATA
Standard ID GB/T 20076-2021 (GB/T20076-2021)
Description (Translated English) Measurement methods of maximum torque and maximum net power of engines for motorcycles and mopeds
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard T81
Classification of International Standard 43.140
Word Count Estimation 14,126
Date of Issue 2021-12-31
Date of Implementation 2022-07-01
Older Standard (superseded by this standard) GB/T 20076-2006
Drafting Organization Tianjin Internal Combustion Engine Research Institute (Tianjin Motorcycle Technology Center)
Administrative Organization National Automotive Standardization Technical Committee
Regulation (derived from) National Standard Announcement No. 17 of 2021
Proposing organization Ministry of Industry and Information Technology of the People's Republic of China
Issuing agency(ies) State Administration for Market Regulation, National Standardization Administration

Standards related to: GB/T 20076-2021

GB/T 20076-2021
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.140
CCS T 81
Replacing GB/T 20076-2006
Measurement methods of maximum torque and maximum
net power of engines for motorcycles and mopeds
ISSUED ON: DECEMBER 31, 2021
IMPLEMENTED ON: JULY 01, 2022
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of China.
Table of Contents
Foreword ... 3 
1 Scope ... 5 
2 Normative references ... 5 
3 Terms and definitions... 5 
4 Test methods ... 6 
5 Correction factors for spark ignition engine power and torque ... 11 
6 Correction factors for compression ignition engine power and torque ... 13 
7 Measurement tolerance for maximum torque and maximum net power ... 16 
8 Test methods for maximum torque and maximum power of hybrid drive systems . 17 
Annex A (normative) Measurement of maximum torque and maximum net power of
engine (by controlling engine temperature) ... 18 
Measurement methods of maximum torque and maximum
net power of engines for motorcycles and mopeds
1 Scope
This Standard describes the measurement methods of maximum torque and maximum
net power of engines for motorcycles and mopeds.
This Standard is applicable to engines for motorcycles and mopeds (hereinafter referred
to as "engines").
2 Normative references
The following referenced documents are indispensable for the application of this
document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
GB 14622, Limits and Measurement Methods for Motorcycle Pollutant Discharge
(China stage IV)
GB 18176, Limits and measurement methods for emissions of pollutants from
mopeds(CHINA IV)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 net power
engine with the accessories listed in Table 2, at the speed specified by the manufacturer,
the power obtained from the end of the engine crankshaft on the test bench
NOTE: If the power can only be measured by the gearbox of the engine, the transmission efficiency
of the gearbox is also considered.
3.2 maximum net power
the maximum power output measured by the engine at full load
3.3 maximum torque
2) If V2< 120km/h and/or ϕ< 0.25m2, the minimum test conditions cannot be met.
The test stand cooling system shall be improved. In this case, the test shall be
carried out in accordance with the method in Annex A and approved by the
manufacturer.
The method specified in this clause is not used for the moped engines and compression
ignition engines.
4.3.5 The engine intake air temperature (ambient air) shall be measured within 0.15m
of the front end of the air filter intake direction. If there is no air filter, measure within
0.15m from the air inlet. Thermometers and thermocouples are protected against
radiation and fuel vapors and inserted directly into the air flow. To obtain a
representative average intake air temperature, an appropriate number of measurement
points shall be set.
4.3.6 The torque, speed and temperature shall remain stable for at least 30s before
starting the measurement.
4.3.7 The speed variation of each measurement point of spark ignition engine for
mopeds shall not exceed ±2%. The deviation between the measured speed of the
motorcycle engine and the selected speed shall not exceed ±1% or ±10r/min. Take the
higher of the two.
4.3.8 Dynamometer load and intake air temperature shall be recorded simultaneously.
Its value shall be the average of two stable recordings taken consecutively. The
difference between the two values of the dynamometer load shall not exceed 2%.
4.3.9 The coolant temperature at the engine coolant outlet shall be maintained within
±5K of the upper limit temperature of the thermostat given by the manufacturer. If there
is no factory given value, the temperature is 353K ± 5K. For air-cooled engines, the
temperature at the manufacturer's specified point shall be maintained between of
the maximum manufacturer's specified temperature under standard conditions.
4.3.10 The fuel temperature shall be measured at the carburetor inlet or the fuel injection
system inlet and the fuel consumption meter. Its value shall be within the range given
by the manufacturer.
4.3.11 The lube oil temperature shall be measured at the crankcase or oil cooler outlet.
Its value shall be within the range given by the manufacturer.
4.3.12 The compression ignition engine temperature shall be maintained within the
limits of 4.3.8 ~ 4.3.10, otherwise an additional adjustment device shall be used.
4.3.13 The exhaust temperature shall be measured at an angle perpendicular to the
airflow at the exhaust manifold, exhaust manifold, or exhaust pipe vent.
4.3.14 If an automatic trigger device is used to measure speed and fuel consumption,
the measurement duration is at least 10s. If using manual device, the duration is at least
20s.
4.3.15 During the type test, the reference fuel that meets the requirements of GB 14622
and GB 18176 shall be used.
4.3.16 During the test, parameters such as torque, rotational speed, intake air
temperature, atmospheric pressure, humidity, oil temperature, fuel temperature, and
exhaust temperature shall be collected and recorded in the original record.
4.4 Tests
Tests shall be carried out at multiple speed points between the manufacturer's
recommended minimum and maximum speeds in order to correctly define the power
curve. The distribution of RPM points shall include the corresponding RPMs for
maximum net engine power and maximum torque. The determination of each rotational
speed shall be the average of at least two stable measurements.
5 Correction factors for spark ignition engine power and
torque
5.1 Meaning of correction factor (α1) for standard ambient conditions and
correction factor (α2) for transmission efficiency
The correction factor (α1) for standard ambient conditions and the correction factor (α2)
for transmission efficiency are multiplied by the measured power and torque to
determine the power and torque obtained under standard ambient conditions. At the
same time ensure that the transmission efficiency is considered during the test.
The corrected power formula is shown in formula (1):
Where,
P0 - Corrected power (crankshaft output power);
α1 - Correction factor for standard ambient conditions;
α2 - Correction coefficient of transmission efficiency;
P - Measured power.
5.2 Ambient conditions
The power correction factor (αd) for standard ambient conditions and the transmission
efficiency correction factor (α2) are multiplied by the measured power and torque, so as
to determine the power and torque obtained under standard ambient conditions. At the
same time ensure that the transmission efficiency is considered during the test.
The corrected power formula is shown in formula (6):
Where,
P0 - Corrected power (crankshaft output power);
αd - Power correction factor for standard ambient conditions;
α2 - Correction coefficient of transmission efficiency;
P - Measured power.
6.2 Standard ambient conditions
Standard ambient conditions require the following:
a) Standard temperature (To) is 298K (25℃);
b) Standard dry pressure (Pso) is 99kPa (990mbar).
6.3 Test ambient conditions
The ambient conditions during the test shall be within the ranges given below:
a) Test temperature (T): 283K~313K;
b) Atmospheric dry pressure (Ps): 80kPa~110kPa.
6.4 Power correction factor (αd) for standard ambient conditions
6.4.1 Determination of power correction factor (αd) for standard ambient
conditions
Under a constant fuel supply rate, the power correction coefficient (αd) of the
compression ignition engine is obtained from formula (7):
Where,
αd - Power correction factor for standard ambient conditions;
fα - Ambient factor;
fm - Characteristic factor of the engine and regulator.
6.4.2 Ambient factor (fα)
The ambient factor (fα) refers to the effect of ambient conditions (pressure, temperature,
humidity) on the intake air of the engine. Different engine types have different factors.
a) The ambient factor of a naturally aspirated or supercharged engine is calculated
according to formula (8):
Where,
fα - Ambient factor;
T - Absolute temperature of the intake air of the engine, in Kelvin (K);
Ps - Atmospheric dry pressure, in kilopascals (kPa).
b) The ambient factor of turbocharged engine is calculated according to formula (9):
Where,
fα - Ambient factor;
T - Absolute temperature of the intake air of the engine, in Kelvin (K);
Ps - Atmospheric dry pressure, in kilopascals (kPa).
6.4.3 Characteristic factor of engine and regulator (fm)
The characteristic factor (fm) of the engine and regulator is a function of the corrected
fuel flow (qc), calculated according to formula (10):
Where,
qc - Corrected fuel flow, calculated according to formula (11):
Annex A
(normative)
Measurement of maximum torque and maximum net power of engine (by
controlling engine temperature)
A.1 The test to determine the maximum torque and maximum net power of the engine
shall be completed in the case of spark ignition engine with full throttle open and
compression ignition engine under the condition of full load of fuel injection pump. The
engine is mounted as listed in Table 2.
A.2 The engine operation during measurement shall be normal and stable, and the air
supply shall be sufficient. The engine shall be run-in under the conditions recommended
by the manufacturer. There can be carbon deposits in the combustion chamber, but it
must be within the scope of the manufacturer's license. Test conditions (such as intake
air temperature) shall be as close as possible to standard ambient conditions (see 5.2.1)
to reduce the influence of the correction factor.
A.3 For the measurement of engine intake air temperature (ambient air), see 4.3.5.
A.4 In a measurement, the speed change of each measurement point shall not exceed
±1%.
A.5 The load reading of the measured engine shall be read from the dynamometer when
the engine monitoring temperature reaches a predetermined value, and the engine speed
remains basically constant.
A.6 For dynamometer load and intake air temperature measurements, see 4.3.8.
A.7 The measurement of fuel consumption can only be carried out when the engine
reaches the specified speed. If using an automatic trigger device to measure speed and
fuel consumption, the measurement duration is at least 10s. If using a manual device,
the duration is at least 20s.
A.8 The coolant temperature at the engine coolant outlet shall be maintained within
±5K of the upper limit temperature of the thermostat given by the manufacturer. If there
is no manufacturer given value, the temperature is 353K ± 5K. For air-cooled engines,
the spark plug gasket temperature shall be maintained within ±10K of the maximum
temperature specified by the manufacturer under standard conditions. If not specified
by the manufacturer, the temperature is 483K±10K.
A.9 The temperature at the spark plug gasket of an air-cooled engine is measured by a
thermometer in conjunction with a thermocouple seal.
...