Path:
Home >
GB/T >
Page490 > GB/T 7036.2-2017
Home >
Standard_List >
GB/T >
Page490 > GB/T 7036.2-2017
GB/T 7036.2-2017 PDF English
US$150.00 · In stock · Download in 9 secondsGB/T 7036.2-2017: Inner Tube of Pneumatic Tyres - Part 2: Inner Tube of Motorcycle Tyres
Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See
step-by-step procedureStatus: Valid
GB/T 7036.2: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 7036.2-2017 | English | 150 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Inner Tube of Pneumatic Tyres - Part 2: Inner Tube of Motorcycle Tyres
| Valid |
| GB 7036.2-2007 | English | 140 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
[GB/T 7036.2-2007] Inner tube of pneumatic tyres -- Part 2: Inner tube of motorcycle tyres
| Obsolete |
| GB 7036.2-1997 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Inner tube of pneumatic tyres--Part 2: Inner tube of motorcycle tyres
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)
PDF Preview: GB/T 7036.2-2017
GB/T 7036.2-2017: Inner Tube of Pneumatic Tyres - Part 2: Inner Tube of Motorcycle Tyres
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT7036.2-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 83.160.10
G 41
Replacing GB/T 7036.2-2007
Inner Tube of Pneumatic Tyres -
Part 2.Inner Tube of Motorcycle Tyres
Issued on. DECEMBER 29, 2017
Implemented on. NOVEMBER 01, 2018
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword... 3
1 Scope... 5
2 Normative References... 5
3 Type of Inner Tube... 5
4 Requirements... 5
5 Test Method... 6
6 Sampling and Inspection Rules... 10
7 Marking... 11
Foreword
GB/T 7036 Inner Tube of Pneumatic Tyres consists of the following two parts.
--- Part 1.Inner Tube of Motor Vehicle Tyres;
--- Part 2.Inner Tube of Motorcycle Tyres.
This Part belongs to Part 2 of GB/T 7036.
This Part was drafted as per the rules specified in GB/T 1.1-2009.
This Part replaced GB/T 7036.2-2007 Inner Tube of Pneumatic Tyres – Part 2.Inner
Tube of Motorcycle Tyres. Compared with GB/T 7036.2-2007, this Part has the major
technical changes as follows.
--- Add “the size of the inner tube shall meet the matching requirements of the used
tyre. When the same inner tube can be applied to different tyres, the
specifications of the tyres that can be matched shall be represented on the inner
tube” (see 4.1 of this Edition);
--- Modify and confirm the size of the rubber base for the small rubber base valve
(see Table 1 of this Edition; Table 1 of Edition 2007);
--- Modify the expression of the aeration measurement position in the air tightness
test method (see 5.1.1 of this Edition; 5.1.1 of Edition 2007);
--- Modify “... and immerse into water for 1min; if there is more than 1 bubble...”
into “... and immerse into water for 1min; if there are 1 or more bubbles...” (see
5.1.3 of this Edition; 5.1.3 of Edition 2007);
--- Modify “rubber base for rubber base valve and tyre body...” into “rubber base
valve and tyre body...” (see Table 1 and 5.5 in this Edition; Table 1 and 5.5 of
Edition 2007);
--- Add the methods for the values of tensile strength and elongation (see 5.2 of this
Edition);
--- Modify “cut a 20mm~30mm-sized mouth at the joint BETWEEN the rubber base
AND the rubber of tyre body OF the sample...” into “cut a 10mm~15mm-sized
mouth at the joint BETWEEN the rubber base AND the rubber of tyre body OF
the sample...”; add a sampling diagram of the bond strength test between the
rubber base valve and the tyre body (see 5.5.1 of this Edition; 5.5.1 of Edition
2007);
--- Add the sampling and inspection rules (see Clause 6 of this Edition);
--- Modify the width of the Type-B inner tube color line from 2mm to 1mm; add “7.3
Type-A inner tube shall not mark the color line used for the Type-B inner tube
specified in 7.2” (see 7.2 and 7.3 of this Edition; 6.2 of Edition 2007).
This Part was proposed by China Petroleum and Chemical Industry Federation.
This Part shall be under the jurisdiction of National Technical Committee for
Standardization of Tyres and Rims (SAC/TC 19).
Drafting organizations of this Part. Xiameng Chen Shin Enterprise Co., Ltd.;
Guangzhou Diamond Tire Co., Ltd.; Kenda Rubber (Shen Zhen) Co., Ltd.; Jiangsu
Speeding Co., Ltd.; Jiangmen Dachangjiang Group Co., Ltd.; and Guangzhou Vanlead
Group Co., Ltd.
Drafting staffs of this Part. Li Ruihua, Chen Jianming, Huang Yaomin, Cao Bin, Chen
Qingsong, Ding Xinghai, Xie Liangchun, Liu Huichun, and Zhou Haibin.
The historical edition replaced by this Standard is as follows.
--- GB 7036-1986, GB 7036-1989;
--- GB 7036.2-1997, GB/T 7036.2-2007.
Inner Tube of Pneumatic Tyres -
Part 2.Inner Tube of Motorcycle Tyres
1 Scope
This Part of GB/T 7036 specifies the types, requirements, test methods, sampling
inspection rules and marks for the inner tube of motorcycle tyres.
This Part is also applicable to the inner tubes of new motorcycle tyres.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 528 Rubber, Vulcanized or Thermoplastic - Determination of Tensile Stress-
Strain Properties
GB/T 532 Rubber, Vulcanized or Thermoplastic - Determination of Adhesion to
Textile Fabric
GB/T 1796.2 Tyre Valves - Part 2.Rubber Base Valves
3 Type of Inner Tube
According to the materials used in the manufacture of the inner tube, it can be divided
into two types. Type-A inner tube made of natural rubber and natural rubber blend,
4 Requirements
4.1 Specification and size
The size of the inner tube shall meet the matching requirements of the used tyre. When
the same inner tube can be applied to different tyres, the specifications of the tyres
that can be matched shall be represented on the inner tube.
4.3 Appearance quality
The inner tube is free of the following appearance defects such as scratches, cracks,
bubbles, sponges, impurities that affect the use performance.
4.3 Air tightness
The inner tube shall have good air tightness and meet the test requirements specified
in 5.1.
5 Test Method
5.1 Air tightness
5.1.1 Inflate the Type-A inner tube; after the sectional circumference of the inner tube
opposite to the valve is 120% width of the double overlapping section of the inner tube,
stand at the room temperature for 12h. Inflate the Type-B inner tube; after the sectional
circumference of the inner tube opposite to the valve is 130% width of the double
overlapping section of the inner tube, stand at the room temperature for 8h.
5.2 Tensile test
The tensile test shall be carried out as per GB/T 528.When using Type-1 cutter to
measure the tensile strength and elongation, separately take 1 specimen along the
circumferential direction of the tyre body (see Figure 1) from the crown center, base
center, upper mold center and lower mold center of the same section on the non-joint
of the inner tube. When measuring the elongation, the tensile strength shall be
measured at the same time; which shall be taken as the tensile strength before the
aging test.
5.3 Joint tensile strength
Specimen. at the crown center, base center, upper mold center, lower mold center; use
a Type-1 cutter to separately take 1 specimen along the circumferential direction of the
tyre body (as shown in Figure 1). The test method shall meet the requirements of GB/T
528; the test result shall be calculated as per Formula (3) by removing the maximum
value S9 and minimum value S12.
5.5 The bond strength and bond force between rubber base valve and tyre body
5.5.1 Bond strength between rubber base valve and tyre body
Cut the sample of valve rubber base from the inner tube; separately make 1 specimen
with width of 10.0mm±0.5mm symmetrically on both sides of the rubber base (as
shown in Figure 2); cut a 10mm~15mm mouth between the specimen rubber base and
the tyre body rubber; separately clamp the rubber base and the tyre into the upper and
lower clampers; perform test as per GB/T 532; take the average value of the results
obtained from the 2 specimens. If the rubber layer is torn off during the peeling period,
then the bond strength at that time is greater than the tensile strength of the rubber;
and is considered qualified; when indicating the result, it shall be explained.
5.6 Absolute value of the tensile strength change rate after aging of the Type-A
inner tube
Test conditions. aging temperature is at 90°C±1°C; aging time is 24h.
6 Sampling and Inspection Rules
6.1 Sampling
For each specification of inner tube, if the output per week exceeds 10000 pieces, the
monthly output shall be regarded as a batch; if the output per week does not exceed
10000 pieces, then each 20000 pieces shall be regarded as a batch; if the output within
6 months since the production date does not exceed 20000 pieces, then the output
within 6 months since the production date shall be regarded as a batch. Take 1 inner
tube from each batch to perform the test as per the requirements of 4.2~4.5.
6.2 Inspection
The inner tube shall be sampled and inspected as per the provisions of 6.1.
All the inner tubes that are delivered for exit-factory use must take the appearance
quality inspection one by one;
7 Marking
7.1 Each inner tube shall have the following marks; thereof, a) ~ c) are permanent
marks; d) is the impressions that can’t be washed off.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked Questions
Question 1: How long will the true-PDF of English version of GB/T 7036.2-2017 be delivered?
Answer: The full copy PDF of English version of GB/T 7036.2-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.
Question 2: Can I share the purchased PDF of GB/T 7036.2-2017_English with my colleagues?
Answer: Yes. The purchased PDF of GB/T 7036.2-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.
Question 3: Does the price include tax/VAT?
Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs):
List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?
Answer: Yes.
www.ChineseStandard.us -- GB/T 7036.2-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.
Question 5: Should I purchase the latest version GB/T 7036.2-2017?
Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 7036.2-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.
How to buy and download a true PDF of English version of GB/T 7036.2-2017?
A step-by-step guide to download PDF of GB/T 7036.2-2017_English
Step 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 7036.2-2017".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9