SN/T 2412.3-2010 English PDFUS$239.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. SN/T 2412.3-2010: General rules for the inspection of import and export steel products. Part 3: Sampling position and size Status: Valid
Basic dataStandard ID: SN/T 2412.3-2010 (SN/T2412.3-2010)Description (Translated English): General rules for the inspection of import and export steel products. Part 3: Sampling position and size Sector / Industry: Commodity Inspection Standard (Recommended) Classification of Chinese Standard: H40 Classification of International Standard: 77.140.01 Word Count Estimation: 9,925 Date of Issue: 2010-01-10 Date of Implementation: 2010-07-16 Regulation (derived from): National Quality Inspection [2010] No. 13 Issuing agency(ies): General Administration of Customs Summary: This standard specifies the import and export of steel sampling position and size of the general requirements. This standard applies to steel (belt), bar, pipe, wire (rope) wood, steel, steel billets and other sampling position and size of the general requirements. SN/T 2412.3-2010: General rules for the inspection of import and export steel products. Part 3: Sampling position and size---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. General rules for the inspection of import Exit inspection and quarantine industry standard book People's Republic of China General inspection of import and export of steel Part 3. Sampling location and size Issued on. 2010-01-10 2010-07-16 implementation People's Republic of China The State Administration of Quality Supervision, Inspection and Quarantine released ForewordSN/T 2412 "General inspection of import and export of steel" is divided into four parts. --- Part 1. General requirements; --- Part 2. Sampling provisions; --- Part 3. Sampling location and size; --- Part 4. sample preparation requirements. This section SN/T 2412 Part 3. Appendix A of this section is an informative annex. This section proposed and managed by the National Certification and Accreditation Administration Committee. This section was drafted by. People's Republic of China Guangdong Entry-Exit Inspection and Quarantine Tianjin People's Republic of China Bureau, People's Republic of China Ningbo Exit Inspection and Quarantine. The main drafters of this section. Chen, Zhou Qi, Cao standard, FU Zhi-Qiang, Li Xiaomin, Tan Ying, somehow Jane, Caoguo Zhou. This standard is the first release of the entry-exit inspection and quarantine industry standards. General inspection of import and export of steel Part 3. Sampling location and size1 ScopeThis section SN/T 2412 provisions of the import and export of steel sampling location and size of the general requirements. General This section applies to steel plate (with), bar, pipe, wire (rope) wood, steel, steel billets and other sampling location and size Claim.2 Terms and definitionsThe following terms and definitions apply to this section. 2.1 Take part in some way on the interception of certain steel products for processing into the test sample process. 2.2 Location where the samples were taken steel. 2.3 Samples taken the length, width and diameter.3 sampling location and size requirements3.1 General requirements 3.1.1 Various types of steel should be determined according to the size of the sampling sites and related standards, some standards in Appendix A. 3.1.2 Refer to Appendix A of the standard, consider consuming sample preparation process and practical feasibility and convenience, unified recommended common Importers Sampling location and the minimum size of steel in Table 1. 3.1.3 When Table 1 does not cover or does not apply, shall be required to determine the relevant product specified in the sampling location and size. 3.2 Special Requirements 3.2.1 sampling sites at the ends, such as ends obvious and normal sites should consider removing abnormal ends after the sampling operation. 3.2.2 When the test sample is necessary to distinguish the steel rolling direction, it should take steps to identify the rolling direction of the steel in the samples taken. 3.2.3 For steel, such as the size of the material can not meet the sampling requirements, the full width of the plate to take the appropriate length. 3.2.4 rope breaking load test using other methods, such as anchoring method, the length of the sample taken should be appropriately extended. 3.2.5 For electrical steel sheet, such as the use of single magnetic measurement sampling length can be shortened to 1000mm; The measurement of magnetic square circle method Energy, should ensure that the sample weighs more than 1.5kg. 3.2.6 For the need of water pressure, flaw detection of pipes should be pressure, testing after passing the required sample size. 3.2.7 When required to retest or arbitration test, should be strictly in accordance with the relevant product standards sampling. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of SN/T 2412.3-2010_English be delivered?Answer: Upon your order, we will start to translate SN/T 2412.3-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of SN/T 2412.3-2010_English with my colleagues?Answer: Yes. The purchased PDF of SN/T 2412.3-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
