QC/T 597.3-2019 PDF EnglishUS$85.00 · In stock · Download in 9 seconds
QC/T 597.3-2019: Specification for fastener with adhesive coating - Part 3: Sealing coatings Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsQC/T 597.3-2019: Specification for fastener with adhesive coating - Part 3: Sealing coatings---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QCT597.3-2019QC AUTOMOBILE INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.040 T 31 Replacing QC/T 597-1999 Specification for fastener with adhesive coating - Part 3: Sealing coatings ISSUED ON: AUGUST 02, 2019 IMPLEMENTED ON: JANUARY 01, 2020 Issued by: Ministry of Industry and Information Technology of PRC Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Requirements ... 4 4 Test method ... 6 5 Inspection rules ... 8 6 Storage ... 8 Specification for fastener with adhesive coating - Part 3: Sealing coatings1 Scope1.1 This Part specifies the requirements, test methods, inspection rules, storage of non- reusable sealing coating (hereinafter referred to as "sealant"), which is pre-applied onto the external thread fasteners (bolt, screw and stud, hereinafter referred to as "bolt"), for the purpose of preventing leakage AND having the sealing function. 1.2 This Part is applicable to the sealing of threaded connection pair, in accordance with GB/T 196, GB/T 197 or GB/T 12716.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard. GB/T 196 General purpose metric screw threads - Basic dimensions GB/T 197 General purpose metric screw threads - Tolerances GB 11121 Gasoline engine oil GB/T 12716 Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on threads GB 17930 Gasoline for motor vehicles GB 19147 Automobile diesel fuels GB 29743 Motor vehicle engine coolant3 Requirements3.1 Sealing at room temperature 3.1.1 After the bolts coated with sealant are fully screwed into the screw holes AND then come into contact with the coolant, it shall ensure that the thread pair does not leak. The test method shall be in accordance with the provisions in 4.2.1. 3.1.2 The bolts coated with sealant are fully screwed into the screw holes; the thread pair shall not leak, after the compressed air is introduced. The test method shall be according to the provisions of 4.2.2. 3.1.3 The bolts coated with sealant are fully screwed into the screw holes; the threaded pairs shall not leak, after being filled with water. The test method shall be in accordance with the provisions in 4.2.3. 3.2 Aging resistance 3.2.1 The bolts coated with sealant are fully screwed into the screw holes AND then come into contact with the engine oil; it shall ensure that the thread pair does not leak. The test method shall be in accordance with the provisions in 4.3.1. 3.2.2 After the bolts coated with sealant are fully screwed into the screw holes AND then come into contact with fuel (gasoline or diesel), it shall be ensured that the thread pair does not leak. The test method shall be in accordance with the provisions in 4.3.2. 3.2.3 The bolts coated with sealant are fully screwed into the screw holes AND then contact with the gearbox oil, it shall ensure that the thread pair does not leak. The test method shall be in accordance with the provisions in 4.3.3. 3.3 Heat resistance After the bolts coated with sealant are fully screwed into the screw holes, place them at 150 °C for 5 hours; then place them at room temperature, which shall meet the requirements of 3.1 and 3.2, respectively. 3.4 Cold resistance After the bolts coated with sealant are fully screwed into the screw holes, place them at -30 °C for 5 hours; then place them at room temperature, which shall meet the requirements of 3.1 and 3.2, respectively. 3.5 Resistance to cold and heat shock After the bolts coated with sealant are fully screwed together with the screw holes, they shall be resistant to cold and heat shocks. The test method shall be according to the provisions of 4.4. 3.6 Bolt pre-painted parts and length Apply the sealant to the bolt threads, for a length equal to the thread diameter ± 1 pitch. Unless otherwise specified, avoid coating within 2 full threads of the bolt end. In order to fully ensure the sealing performance, the sealant coating length shall not be less than 3 full pitches. The sealant is applied at an angle of 360° (sealant is applied all around). 4.1.2.3 The bolts shall not produce clamping force, after they are screwed together. 4.1.2.4 When the bolts are screwed into the screw holes on the pressure vessel, the sealant shall be fully engaged with the screw holes. 4.2 Leakage test under room temperature, different test media and working conditions 4.2.1 Coolant Use the liquid, which is fully mixed by 40% water, fluorescent agent, cooling liquid in accordance with GB 29743, as the test medium. Screw the bolts, which are coated with sealant, into the screw holes of the 1 MPa steel pressure vessel. Keep the pressure for 1 min. Observe under ultraviolet light. The thread pair shall have no leaks. 4.2.2 Compressed air Use compressed air as the test medium. Apply soap solution to the screwed part of the bolt. Keep the pressure in the screw hole of the 1 MPa steel container, for 1 min. The thread pair shall not have any leakage. 4.2.3 Water For bolts coated with sealant, use water as the test medium. Keep the pressure in a steel pressure vessel of 1 MPa, for 1 min. There shall be no leakage in the thread pair. 4.3 Aging resistance test under different test media and working conditions 4.3.1 Engine oil Use the liquid, which is fully mixed by the engine oil that complies with the provisions of GB 11121 AND fluorescent agent, as the test medium. Screw the sealant-coated bolts into the screw holes of the steel pressure vessel, which has a pressure of 0.4 MPa. Hold the pressure, under the environmental conditions of (150 ± 2) °C, for 5 h. Observe it under ultraviolet light. The thread pair shall not show any leakage. 4.3.2 Fuel (gasoline or diesel) Use the liquid, which is fully mixed with the gasoline for vehicles specified in GB 17930 or diesel oil for vehicles specified in GB 19147, fluorescent agent, as the test medium. Screw the bolts coated with sealant into the screw holes of the 0.4 MPa steel pressure vessel. Hold the pressure at (70 ± 2) °C for 5 hours. When viewed under ultraviolet light, there shall be no leakage from the threaded pair. 4.3.3 Transmission oil ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of QC/T 597.3-2019 be delivered?Answer: The full copy PDF of English version of QC/T 597.3-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of QC/T 597.3-2019_English with my colleagues?Answer: Yes. The purchased PDF of QC/T 597.3-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QC/T 597.3-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of QC/T 597.3-2019?A step-by-step guide to download PDF of QC/T 597.3-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "QC/T 597.3-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
