JY/T 0130-2019 English PDFUS$149.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. JY/T 0130-2019: Counting sticks Status: Valid JY/T 0130: Historical versions
Basic dataStandard ID: JY/T 0130-2019 (JY/T0130-2019)Description (Translated English): Counting sticks Sector / Industry: Education Industry Standard (Recommended) Classification of Chinese Standard: Y51 Word Count Estimation: 6,678 Date of Issue: 2019-04-08 Date of Implementation: 2019-09-01 Older Standard (superseded by this standard): JY 0130-1991 Regulation (derived from): Natural Resources Department Announcement No. 7 of 2019 Issuing agency(ies): Ministry of Education of the People's Republic of China JY/T 0130-2019: Counting sticks---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.(Counting rod (stick)) ICS 03.180 Y 51 Education Industry Standard of the People's Republic of China Replacing JY/T 0130-1991 Counting stick (stick) Counting sticks Published on April 04,.2019 2019--09--01 Implementation Published by the Ministry of Education of the People's Republic of China JY ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces JY/T 0130-1991 "Counting Sticks". Compared with JY/T 0130-1991, except for editorial changes The changes are as follows. -Change the standard name; -Added normative references (see Chapter 2); -Include the counting stick in the scope of the standard (see Chapter 1); -The length of counting sticks (sticks) for young children has been modified (see Table 1, 4.3 of the.1991 version); -Added safety requirements and test methods (see 4.5 and 5.3); -Added defect classification of product technical indicators (see 6.2). Please note that some elements of this standard may involve patents. The issuer of this standard is not responsible for identifying these patents. This standard is proposed by the Basic Education Department of the Ministry of Education of the People's Republic of China. This standard is under the jurisdiction of the National Technical Committee for Educational Equipment Standardization Technical Committee for Children and Preschool Education (SAC/TC 125/SC6). This standard was drafted. Educational Equipment Research and Development Center of Ministry of Education, Anhui Zhuangyuanlang Electronic Technology Co., Ltd., Hefei Yunlianhong Da Information Technology Co., Ltd. The main drafters of this standard. Zhu Xiaocui, Dang Jianwei, Jiang Zhimou, Zhao Meixuan,. This standard replaces JY/T 0130-1991. The release of previous versions of this standard instead of the standard is as follows. --JY/T 0130-1991. Xia Shulan Counting stick1 ScopeThis standard specifies the classification, technical requirements, test methods, inspection rules, signs, instructions, packaging, and transportation of counting sticks (sticks). And storage. This standard applies to counting sticks (sticks) used in children's computing lessons and games.2 Normative referencesThe following documents are essential for the application of this document. For dated references, only the dated version applies to the document. For undated references, the latest version (including all amendments) applies to this document. GB/T 1931-2009 Wood moisture content determination method GB 6675.1-2014 Toy Safety Part 1. Basic Specifications GB 6675.2-2014 Toy safety Part 2. Mechanical and physical properties GB 6675.4 Toy Safety Part 4. Migration of Specific Elements GB/T 22048 Determination of specific phthalate plasticizers in toys and children's products JY/T 0001-2003 General quality requirements for teaching instruments and equipment products JY/T 0002-2003 Inspection rules for teaching instruments and equipment products JY/T 0026-1991 teaching instrument and teaching equipment product model naming method3 categoriesThe products are divided into three types. teacher demonstration, student grouping and toddler use.4 Technical requirements4.1 Appearance The cross-sectional shape of the product can be square, circular or regular polygon. 4.2 Color The color of the product can be the original color of the material or red, yellow, blue, green, and white (basic colors). 4.3 Size and quantity The size and number of counting sticks (sticks) shall meet the requirements of Table 1. 4.4 Appearance and workmanship 4.4.1 The wooden parts should be straight, and wood with no knots and degreasing and drying treatment should be used. The moisture content should be in accordance with 6.28 of JY/T 0001-2003. Requirements. 4.4.2 Plastic parts shall be solid, straight, and the surface shall be flat and clean, and shall meet the appearance requirements of 7.7 of JY/T 0001-2003 for plastic parts. 4.4.3 Teachers' demonstration counting sticks (sticks) shall be magnetically added. Each counting stick shall be able to withstand 0.3N when it is placed in parallel to a steel plate placed vertically. Pull straight down without sliding. Table 1 Size and quantity of counting sticks Application Length Section Size Color Quantity Remarks For teacher presentation 195 mm ～ 205 mm 10 mm two kinds of 50 each 10 bundles For student grouping For toddlers 100 mm ～ 120 mm4 mm five types20 pieces each 70 mm ～ 80 mm, 10 pieces each Note. The section size of the product is calculated based on the circumscribed circle diameter of the section shape. 4.5 Security 4.5.1 All exposed accessible parts shall have no dangerous sharp edges and tips that may cause harm to human body. Sharp edges and corners should be inverted Edges and rounds. 4.5.2 Chemical substances exposed to materials used in products after normal use and after abuse tests should not have a negative impact on human health, It shall meet the requirements of 5.3.1, 5.3.2, 5.3.3 and 5.3.7 in GB 6675.1-2014. 4.5.3 Others shall meet the general requirements for product safety used in lower grades of elementary schools in 5.9 and 5.10 of JY/T 0001-2003.5 Test method5.1 Dimensions Measured with a steel ruler with a graduation value of 1 mm and a vernier caliper with a graduation value of 0.02 mm, which shall meet the requirements of 4.3. 5.2 Wood moisture content It shall be in accordance with Chapters 5 and 6 of GB 1931-2009 and shall meet the requirements of 4.4.1. 5.3 Magnetic strength The magnetic strength tensile test shall be measured with a dynamometer with a minimum division value of 0.02 and shall meet the requirements of 4.4.3. 5.4 Security 5.4.1 Accessible exposed dangerous sharp edges and tips shall be tested in accordance with 5.8 and 5.9 of GB 6675.2-2014, respectively. 5.4.2 The migratable elements in the materials used shall be tested according to the method of GB 6675.4, and the results shall meet the requirements of 4.5.2. 5.4.3 The phthalate plasticizer in the materials used in the product is tested according to the method of GB/T 22048, and the results should meet the requirements of 4.5.2. 5.5 Other Sensory test.6 Inspection rules6.1 Inspection classification Product inspection is divided into factory inspection, type inspection and quality supervision inspection. 6.2 Inspection items, inspection methods and defect classification The inspection items, inspection methods and defect classification of factory inspection and type inspection shall be in accordance with Table 2. Table 2 Inspection items, inspection methods, and defect classification of factory inspection and type inspection Serial number inspection standard provisions factory inspection type inspection defect classification 1 stick (stick) length 4.3 ● ▲ A 2 Section size 4.3 ● ▲ A 3 colors 4.2 ○ ▲ B 4 Quantity 4.3 ● ▲ A 5 Water content of wooden parts 4.4.1 ○ ▲ A Teacher demonstrates the magnetism and strength 4.4.3 ● ▲ A 7 Other appearance 4.4.2 ○ ▲ B safety Sharp edges and tips 4.5.1 ○ ▲ A 9 Material safety 4.5.2 ○ ▲ A 10 Other safety requirements 4.5.3 ○ ▲ A Note. “●” in the table means all inspection items, “○” means sampling inspection items, “-” means no inspection items, and “▲” means inspection should be performed project. 6.3 Lot rules and sampling methods 6.3.1 The factory inspection shall be batched according to the natural batch of delivery, and the type inspection shall be batched according to the stock array. 6.3.2 When leaving the factory for inspection, inspect all the inspection items first, take samples from the qualified products of all inspection items, and inspect the items for sampling inspection. 6.3.3 The samples for type inspection shall be taken from the products that passed the factory inspection. 6.3.4 The sampling methods for factory inspection and type inspection shall be in accordance with the relevant provisions of JY/T 0002. 6.4 Non-conformance determination 6.4.1 The failure criterion of a single sample shall be implemented in accordance with 4.3 of JY/T 0002-2003. 6.4.2 In Table 3, "A" is the main technical index, and "B" is the non-main technical index. 6.5 Review rules 6.5.1 Unqualified batches and products can be submitted for re-inspection after rework. 6.5.2 If the cause of the batch disqualification is a sampling inspection item, the item shall be fully inspected during the re-inspection. 6.6 Quality supervision inspection Refer to type inspection. 7 Signs, instructions, packaging, transportation and storage Product marking, packaging, transportation, storage, and use instructions shall be in accordance with the provisions of Chapters 11 and 12 of JY/T 0001-2003. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of JY/T 0130-2019_English be delivered?Answer: Upon your order, we will start to translate JY/T 0130-2019_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of JY/T 0130-2019_English with my colleagues?Answer: Yes. The purchased PDF of JY/T 0130-2019_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version JY/T 0130-2019?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version JY/T 0130-2019 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
