JJF 1242-2010 English PDFUS$459.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. JJF 1242-2010: Calibration Specification for Laser Tracker 3-Dimensional Measuring System Status: Valid JJF 1242: Historical versions
Basic dataStandard ID: JJF 1242-2010 (JJF1242-2010)Description (Translated English): Calibration Specification for Laser Tracker 3-Dimensional Measuring System Sector / Industry: Metrology & Measurement Industry Standard Classification of Chinese Standard: A52 Classification of International Standard: 17.040 Word Count Estimation: 20,281 Date of Issue: 2010-01-05 Date of Implementation: 2010-04-05 Quoted Standard: ASME B89.4.19-2006; JJF 1001-1998; JJF 1094-2003; JJF 1059-1999 Regulation (derived from): AQSIQ Announcement No. 3 of 2010 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine Summary: This standard specifies the laser tracking three-dimensional coordinate measurement system calibration method, the following example to be expressed in laser tracker, suitable for industrial measurement instruments as laser tracker and the same principle to other measuring instruments calibrated. JJF 1242-2010: Calibration Specification for Laser Tracker 3-Dimensional Measuring System---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Calibration Specification for Laser Tracker 3-Dimensional Measuring System People's Republic of China National Measurement Specifications Laser tracking 3D coordinate measuring system calibration specification CalibrationSpecification for LaserTracker 2010-01-05 released 2010-04-05 implementation General Administration of Quality Supervision, Inspection and Quarantine released Laser tracking 3D coordinate measuring system Calibration specifications This standard was approved by the General Administration of Quality Supervision, Inspection and Quarantine on January 05,.2010 and has been approved since April.2010 Put into effect on the 05th. The focal point. National geometric length measurement technology committee Drafting unit. China Institute of Metrology This regulation shall be explained by the focal point Drafters of this Code. Wang Wei-nong (China Institute of Metrology) Pei Li Mei (China Institute of Metrology) Ren State-owned (China Institute of Metrology) table of Contents1 Scope (1) 2 References (1) 3 Terms (1) 4 Overview (2) 5 Metrology (2) 5.1 Point-to-point length indication error (2) 5.2 double-sided indication error (2) 5.3 distance indication error (2) 5.4 spherical reflection target error (2) 5.5 Dynamic speed limit (2) 5.6 Dynamic Indication Error (2) 5.7 Dynamic indication variation (2) 6 Calibration conditions (3) 6.1 Environmental conditions (3) 6.2 standard equipment (3) 7 Calibration Items and Methods (3) 7.1 Point-to-point length indication error (3) 7.2 double-sided indication error (6) 7.3 distance indication error (7) 7.4 spherical reflection target error (8) 7.5 Dynamic speed limit (9) 7.6 Dynamic Indication Error (9) 7.7 Dynamic indication variation (9) 7.8 Failure to meet the maximum allowable error requirements (9) 8 Calibration Results (10) 9 time interval of correction (10) Appendix A Rating Conditions and Calibration Results Recording Table (11) Appendix B Uncertainty of Reference Length with Stable Target Block Distance (14) Laser tracking 3D coordinate measuring system calibration specification1 ScopeThis standard specifies the laser tracking three-dimensional coordinate measuring system calibration method, the following laser tracker as an example Expression, suitable for industrial laser measuring instrument tracker and the principle of the same calibration of other measuring instruments.2 ReferencesASMEB89.4.19-2006 Performance Evaluation of Laser-Based Ball Coordinate Measuring Systems PerformanceEvalu- ation of Laser-Based Spherical Coordinate Measurement System General measurement terms and definitions JJF 1094-2003 Measuring instruments for characterization Evaluation and Expression of Uncertainty in Measurement When using this specification, care should be taken to use the currently valid version of the above referenced document.3 TermsThe following provides definitions of terms used in this specification. Other terms and definitions conform to JJF 1001-1998. 3.1 Scope finder absolutedistancemeter, ADM Built-in laser tracker range finder, also known as the electronic rangefinder (electronicdistancemeter, EDM). 3.2 front/rear frontsight/backsight These are the modes of measurement. Foreground is the instrument's normal measurement mode. Rear view is obtained by the following method The vertical axis is rotated by 180 ° and the beam is rotated around the horizontal axis to recalibrate the target point. Note that forward/backward vision is sometimes referred to as frontal/inverted vision or face 1/face 2. 3.3 base point homepoint Relative laser tracker fixed position, and the relationship between the origin of the coordinate system of the instrument has been accurately determined. Note. The base point is used as the distance reference for the laser tracker rangefinder. 3.4 Interferometer interferometer, IFM Laser Displacement Interferometer built into laser tracker. 3.5 Measurement Capability Index measurementcapabilityindex, Cm The ratio of the absolute value of the maximum allowable error of the length measurement to the extended uncertainty of the corresponding reference length. Cm = | MPE |/U 3.6 spherical reflective target sphericalymountedretroreflector, SMR Reflective target mounted in a spherical housing. Note that for open pyramids, the apex is usually adjusted to match the center of the sphere. 3.7 two-sided test two-facetest Test with front/rear view to assess the effect of some specific geometric errors on the instrument. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of JJF 1242-2010_English be delivered?Answer: Upon your order, we will start to translate JJF 1242-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of JJF 1242-2010_English with my colleagues?Answer: Yes. The purchased PDF of JJF 1242-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version JJF 1242-2010?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version JJF 1242-2010 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |