GB/T 41850.8-2022 English PDFUS$514.00 ยท In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 41850.8-2022: Mechanical vibration - Measurement and evaluation of machine vibration - Part 8: Reciprocating compressor systems Status: Valid
Basic dataStandard ID: GB/T 41850.8-2022 (GB/T41850.8-2022)Description (Translated English): Mechanical vibration - Measurement and evaluation of machine vibration - Part 8: Reciprocating compressor systems Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J04 Classification of International Standard: 17.160 Word Count Estimation: 30,397 Date of Issue: 2022-10-14 Date of Implementation: 2022-10-12 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 41850.8-2022: Mechanical vibration - Measurement and evaluation of machine vibration - Part 8: Reciprocating compressor systems---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Mechanical vibration -- Measurement and evaluation of machine vibration -- Part 8.Reciprocating compressor systems ICS 17.160 CCSJ04 National Standards of People's Republic of China Mechanical Vibration Measurement and Evaluation of Machine Vibration Part 8.Reciprocating compressor systems (ISO 20816-8.2018, IDT) Published on 2022-10-12 2022-10-12 Implementation State Administration for Market Regulation Released by the National Standardization Administration directory Preface I Introduction II 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Vibration measurement 2 4.1 Measurement method 2 4.2 Measuring instruments and measuring quantities 3 4.3 Measuring position and measuring direction 3 4.4 Operating conditions 6 4.5 Recording of measurement results 7 5 Vibration Evaluation Criteria7 5.1 Measurements 7 5.2 Evaluation area 7 5.3 Acceptable recommended value of total vibration value (2Hz~1000Hz) 8 Appendix A (Normative) Measurement Information Requirements 11 A.1 Compressor Details 11 A.2 Measurements 11 A.3 Additional Information 12 Appendix B (informative) Curve of limit value of total vibration velocity value 13 B.1 General 13 B.2 Vibration velocity total value limit curve Figure 13 Appendix C (Informative) Measurement of Vibration Values on Crosshead Slides 17 C.1 General 17 C.2 Measurement location and orientation 17 C.3 Acceptable Vibration Recommendations for Crosshead Slides18 Appendix D (Informative) RMS, Peak and Crest Factor 20 D.1 General 20 D.2 RMS, peak and crest factor 20 Appendix E (normative) Small Bore Connection (SBC) 22 E.1 General 22 E.2 Measurement location and orientation 24 E.3 Recommended Values for Acceptable Relative Vibration Velocities for Small Bore Connections 24 E.4 Relative vibration velocity total value limit Figure 25 Reference 26 forewordThis document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules of Standardization Documents" Drafting. This document is part 8 of GB/T 41850 "Measuring and Evaluation of Mechanical Vibration Machine Vibration". GB/T 41850 has been released the following parts. --- Part 8.Reciprocating compressor systems. This document is identical to ISO 20816-8.2018 "Mechanical vibration measurement and evaluation of machine vibration - Part 8.Reciprocating compressors system". Please note that some content of this document may be patented. The issuing agency of this document assumes no responsibility for identifying patents. This document is proposed and managed by the National Standardization Technical Committee on Mechanical Vibration, Shock and Condition Monitoring (SAC/TC53). This document is drafted by. China Southern Power Grid Power Technology Co., Ltd., Zhengzhou Machinery Research Institute Co., Ltd., China Testing Technology Research Institute of Mechanics, Guangdong Power Grid Co., Ltd. Electric Power Research Institute, Huadian Electric Power Research Institute Co., Ltd., Dongguan Zhuo Maoyi Appliance Co., Ltd. The main drafters of this document. Liu Shi, Ma Weiping, Yang Yi, Gao Qingshui, Zhang Chu, Zhu Sha, Huang Zheng, Huang Haizhou, Ou Wenjun, Qian Yihua, Liu Zhigang, Guo Xinran, Han Dan, Cai Yuyuan.IntroductionToday's machines operate under high-speed, heavy-load, variable-load conditions, and the working conditions are getting worse and worse. For more efficient use of materials, machine Design and use restrictions are even tighter. It is generally expected that the machine will work continuously and the period between repairs is 2 or 3 years, so More restrictive requirements are specified for the vibration amplitude of the machine to ensure its continuous safe and reliable operation. GB/T 41850 "Mechanical vibration "Measurement and Evaluation of Machine Vibration" is an important basic standard for the measurement and evaluation of machine vibration. Methods of measuring and evaluating machine vibration on rotating parts. GB/T 41850 is intended to consist of the following parts. --- Part 1.General. The purpose is to give a method for measuring and evaluating various types of machine vibration on non-rotating parts and rotating shafts. general requirements. ---Part 2.Above 40MW, with sliding bearing and rated speed of 1500r/min, 1800r/min, 3000r/min and 3600r/min, land-installed gas turbines, steam turbines and generators. The purpose is to give gas for large land installations Specific evaluation of turbine, steam turbine and generator bearing housing and shaft vibration. --- Part 4.Gas turbines above 3MW with sliding bearings. The purpose is to give gas turbines not covered in Part 2 Specific evaluation of machine housing vibration and shaft vibration. --- Part 5.Hydroelectric and pumped storage power station units. The purpose is to give the bearing of the hydroelectric power generation and pumped storage power station units Guidelines for the evaluation of seat and shaft vibration measurements. --- Part 8.Reciprocating compressor systems. The purpose is to establish a characteristic for the measurement and classification of mechanical vibration of reciprocating compressor system. special procedures and guidelines. --- Part 9.Gearing. The purpose is to give specific provisions for the measurement and evaluation of vibrations in gear units. This document establishes methods and guidelines for the measurement and classification of mechanical vibration of reciprocating compressors. In general, this document addresses the main Vibration of structures (including foundations, pulsation dampers and piping systems), the vibration recommendations given are mainly used for vibration classification and to avoid installation In the event of problems with ancillary equipment on these structures, this document gives recommended measurement and evaluation criteria. Typical characteristics of reciprocating compressors are reciprocating mass, periodically varying torque, cylinder expansion and dynamic dampers, pulsating forces on the piping system, all of these characteristics lead to considerable alternating loads on the main bearing and vibration of the compressor system verb. move. Generally speaking, the vibration magnitude of reciprocating compressor system is higher than that of rotary compressor system, but they are mainly caused by the design characteristics of the compressor. Therefore, reciprocating compressors operate more stably than rotary compressors during the service life of the system. In a reciprocating compressor system, measured on the compressor main structure (including foundation, pulsation damper, and piping system) and according to this paper The quantitative vibration of parts only gives a rough description of the vibration state of the internal components of the machine. When the recommended values based on experience with similar compressor systems are exceeded, the damage mainly occurs in the parts connected to the machine (such as meters, heat exchangers, filters, pumps, etc.), components that connect compressors to peripheral equipment (such as pipes) or monitoring instruments installed on machines (such as pressure force meter, thermometer). The assessment of damage by vibration depends primarily on the design and installation of these components. In some cases, the compressor's Certain components may require specific measurements to ensure that vibration does not cause damage to the machine. Due to the many types of components assembled by the machine, Even if the measured values are within the recommended values of this document, problems may still occur. The above-mentioned local vibration problems can be corrected by specific "local measures" such as eliminating resonance. Nonetheless, experience shows that in large In most cases it is feasible to specify a measurable variable to describe the vibration state and to give its recommended value. This shows that according to measurable variables and Recommended value, which can give a reliable evaluation in most cases. Abnormalities of internal compressor components caused by vibration are unlikely to occur if the magnitude of vibration measured in accordance with this document does not exceed the recommended value wear. The vibration value of the reciprocating compressor system is not only affected by the characteristics of the machine itself, but also by the foundation to a large extent. Reciprocating The compressor can be regarded as a vibration source, and the vibration isolation between the compressor and the foundation is necessary. The vibration response of the foundation and the vibration of adjacent equipment, will affect the compressor The system has a considerable impact. Mechanical Vibration Measurement and Evaluation of Machine Vibration Part 8.Reciprocating compressor systems1 ScopeThis document establishes procedures and guidelines for the measurement and classification of mechanical vibration in reciprocating compressor systems. The defined vibration value is mainly used for Vibration staging of compressor systems and avoidance of reciprocating compressor system components (foundation, compressor, dampers, piping and Fatigue problems of accessory equipment of the system). Shaft vibration is not considered. This document applies to rigidly mounted reciprocating compressor systems with a rated speed of 120r/min~1800r/min. proposed overall The evaluation criteria are related to the measurement method used. This document is also used to evaluate whether the vibration of the machine has any effect on the equipment directly mounted on the machine. Adverse effects such as pulsation dampers and piping systems. Note. The criteria presented in this document can also be used for reciprocating compressors other than the specified speed, but in this case different evaluation criteria may be used. For machines driving reciprocating compressors, compliance with ISO 10816, other parts of ISO 20816 or other relevant standards will be and grading to evaluate. This document does not include drivers. The application of this document is limited when considering the effects of internal parts of the machine, such as valves, pistons, piston rings, etc. may be detected from measurements. The identification of such problems may require research into diagnostic techniques, which are beyond the scope of this document. Reciprocating compressor systems to which this document applies include. ---Horizontal, vertical, V-type, W-type, L-type compressors; --- Fixed speed and variable speed compressors; --- Compressors driven by electric motors, gas engines, diesel engines and steam turbines, with or without gearboxes, flexible or rigid couplings connector; --- Oil-free and oil-lubricated reciprocating compressors. This document does not apply to ultra-high pressure compressors. This document does not apply to condition monitoring, nor is noise within the scope of this document.2 Normative referencesThe contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, dated citations documents, only the version corresponding to that date applies to this document; for undated references, the latest edition (including all amendments) applies to this document. ring-Vocabulary) Note. GB/T 2298-2010 Mechanical Vibration, Shock and Condition Monitoring Vocabulary (ISO 2041.2009, IDT).3 Terms and DefinitionsThe terms and definitions defined in ISO 2041 and the following apply to this document. 3.1 compressor system Mechanical system consisting of foundation, compressor (crankcase, crosshead slide, cylinder), pulsation damper and piping. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 41850.8-2022_English be delivered?Answer: Upon your order, we will start to translate GB/T 41850.8-2022_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 41850.8-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 41850.8-2022_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
