GB/T 37153-2018 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
GB/T 37153-2018: Acoustic vehicle alerting system of electric vehicles running at low speed Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 37153-2018: Acoustic vehicle alerting system of electric vehicles running at low speed---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT37153-2018GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.040.20 T 35 Acoustic vehicle alerting system of electric vehicles running at low speed [ECE-R138, Uniform provisions concerning the approval of Quiet Road Transport Vehicles with regard to their reduced audibility (QRTV), NEQ] Issued on. DECEMBER 28, 2018 Implemented on. JULY 01, 2019 Issued by. State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Normative references... 4 3 Terms and definitions... 4 4 General requirements... 6 5 Test methods... 81 ScopeThis Standard specifies requirements and test methods for vehicle speed range, sound level limit, frequency requirements, sound type, and pause switch of acoustic vehicle alerting system of electric vehicles running at low speed (hereinafter referred to as “acoustic-alerting system”). This Standard is applicable to pure electric vehicles of the Category-M1 and N1 categories, hybrid electric vehicles with pure electric driving modes, and fuel cell electric vehicles.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB 1495, Permissible noise limit emitted by power-driven vehicles GB/T 3241-2010, Electroacoustics - Octave-band and fractional-octave- band filters GB/T 3785.1-2010, Electroacoustics - Sound level meters - Part 1. Specifications GB/T 12534, Motor vehicles - General rules of road test method GB/T 15173-2010, Electroacoustics - Sound calibrators GB/T 19596, Terminology of electric vehicles GB 50800-2012, Technical code for anechoic and semi-anechoic rooms3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 19596 as well as the followings apply. 3.1 acoustic vehicle alerting system; AVAS a system for issuing a prompt sound to effectively transmit information to other road users when the noise value emitted by the vehicle is below a certain value 3.2 acoustic vehicle alerting system of electric vehicle running at low speed a prompt sound from the vehicle’s acoustic-alerting system when the speed of the electric vehicle is lower than a certain value 3.6 rear plane of the vehicle a vertical plane tangent to the trailing edge of the vehicle 3.7 sound pressure level; SPL the base 10 logarithm of the ratio of the square root sound pressure to the reference sound pressure multiplied by 20 3.8 weighted sound level sound level measured by a weighted network filter4 General requirements4.1 Working speed range The working speed range of the acoustic-alerting system shall be at least greater than 0km/h and less than or equal to 20km/h. 4.2 Sound level limit 4.2.1 The noise of the electric vehicle measured by the measurement method specified in 5.6.2 shall be on each 1/3 octave included in it. At least two of the 1/3 octaves are not less than the sound levels specified in Table 1, and at the same time meet the requirements for the total sound level in Table 1. 4.2.2 Vehicles equipped with the acoustic-alerting system shall not emit more than 75dB(A) of noise at the most when driving. 4.3 Frequency requirements 4.3.1 Frequency range The sound of a vehicle equipped with the acoustic-alerting system shall contain at least two 1/3 octaves as specified in Table 1, and at least one 1/3 octave below 1600 Hz (including 1600). The minimum sound level of these two 1/3 octaves shall not be lower than the corresponding sound level limit specified in Table 1. 4.5 Pause switch 4.5.1 For vehicles equipped with the acoustic-alerting system, the manufacturer can choose whether to configure the pause switch. 4.5.2 The pause switch shall be placed in a position where the driver can see, touch and operate under normal driving conditions. 4.5.3 When the pause switch is activated, there shall be a clear signal device (acoustic, optical, electrical or other device) release signal to alert the driver that the acoustic-alerting system running at low speed has been suspended.5 Test methods5.1 Test equipment 5.1.1 Meteorological measuring equipment Meteorological measuring instruments are mainly used to monitor environmental conditions during the test. The accuracy shall meet the following requirements. 5.1.2 Acoustic measuring equipment 5.2 Weather condition During the test, meteorological conditions shall meet the following requirements. 5.3 Test site 5.3.1 Outdoor test 5.3.1.1 Outdoor test conditions Outdoor test sites and pavements shall comply with the requirements of GB 1495. 5.3.1.2 Microphone position The microphone placement position is shown in P and P' in Figures 1 and 2.Its distance to the CC' line is 2.0m ± 0.05m, and 1.2m ± 0.02m upward on the ground surface. The reference direction shall be horizontal and point vertically to the CC' line of the vehicle's operation. 5.3.2 Indoor semi-anechoic or muffling test 5.3.2.1 Indoor semi-anechoic or muffling test conditions This clause specifies the conditions on the road that simulate the operation of all systems during the test, or only the conditions applicable to the acoustic- alerting system operating mode. 5.4 Vehicle status The vehicle test mass is the curb weight +75kg. 5.5 Background noise 5.5.1 Measurement method of background noise A-weighted sound level When measuring background noise, measure at least 10s continuously. When calculating the background noise by using a 10s sound obtained from the measurement, make sure that the sound is typical background noise and does not contain any transient interference. 5.5.2 Correction method of vehicle A-weighted sound level measurement The noise outside the vehicle shall be corrected according to the difference between the maximum and minimum values of the background noise at the time of measurement. Ltest correction = Ltest - Lcorrection. 5.6.2.2 Constant speed test 5.6.2.2.1 Constant speed test when the vehicle moving forward When testing in the outdoor field shown in Figure 6, the path of the vehicle centerline shall be as close as possible to the CC' line throughout the test. The front plane of the vehicle shall pass through the AA' line at the beginning of the test. The rear plane of the vehicle shall pass through the BB' line at the end of the test, as shown in Figure 1.The vehicle shall maintain a constant test speed throughout the operation. 5.6.2.2.2 Simulated constant speed test under vehicle static state When the vehicle is being tested indoors or outdoors, the front plane of the vehicle shall be placed on the PP' line as shown in Figure 4 of 5.3.2.2.By providing an external signal to simulate the test vehicle speed, the vehicle shall maintain a constant simulated test vehicle speed of at least 5s. 5.6.2.3 Reverse test 5.6.2.3.1 Reverse test during driving When the vehicle is tested in the outdoor field shown in Figure 6, the path of the vehicle centerline shall be as close as possible to the CC' line throughout the test. The rear plane of the vehicle shall pass through the AA’ line at the beginning of the test. The front plane of the vehicle shall pass through the BB' line at the end of the test, as shown in Figure 2.The vehicle shall maintain a constant test speed throughout the operation. 5.6.3 Measurement data and recorded values Under each test condition, at least 4 measurements shall be taken on both sides of the vehicle. 5.7 Frequency shift test 5.7.1 Analytical equipment requirements Digital sound recording system shall be at least 16-bit accurate. Sampling rate, range, and dynamic range are suitable for signals that require testing. The frequency of the test results shall have sufficient accuracy. The setting of the analytical equipment shall be determined by the automobile manufacturer and the testing agency. 5.7.2 Instrument and signal processing The sound analysis system shall have the ability to perform a spectrum analysis of a frequency range containing all frequencies of interest at a certain sampling rate. 5.7.3 Test selection For the frequency shift requirement in 4.3.2, choose one of the following methods for detection. Method One. outdoor vehicle road operation test. Method Two. outdoor vehicle road simulation test. use an external signal generator to drive the acoustic-alerting system running at low speed to simulate vehicle operation. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 37153-2018 be delivered?Answer: The full copy PDF of English version of GB/T 37153-2018 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 37153-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 37153-2018_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 37153-2018 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 37153-2018?A step-by-step guide to download PDF of GB/T 37153-2018_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 37153-2018". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
