GB/T 28889-2012 English PDFUS$299.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 28889-2012: Test method for In-plane shear properties of composite materials Status: Valid
Basic dataStandard ID: GB/T 28889-2012 (GB/T28889-2012)Description (Translated English): Test method for In-plane shear properties of composite materials Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: Q23 Classification of International Standard: 83.120 Word Count Estimation: 13,131 Quoted Standard: GB/T 1446; GB/T 3961 Adopted Standard: ASTM D7078/D7078M-2005, MOD Regulation (derived from): National Standards Bulletin 2012 No. 28 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the fiber reinforced plastic in-plane shear properties of the test equipment, specimen preparation, test conditions, test procedures and results of calculation. This standard applies to the determination of symmetrical ply fiber-re GB/T 28889-2012: Test method for In-plane shear properties of composite materials---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Test method for In-plane shear properties of composite materials ICS 83.120 Q23 National Standards of People's Republic of China Composite inner surface shear performance test method Issued on. 2012-11-05 2013-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This standard uses redrafted Law Amendment uses ASTMD7078/D7078M-05 "V-notched rail shear composite shear Test methods. " This standard ASTM D7078/D7078M-05 compared to more adjustments in the structure, listed in Appendix A of this standard and ASTMD7078/reg number control list D7078M-05's. The existence of standards and ASTMD7078/D7078M-05 compared to the technical differences between the terms of these differences have been involved in through the outside Margin vertical single line blank position (|) have been marked, in Appendix B gives the corresponding list of technical differences and their causes. The standard proposed by China Building Materials Federation. The standard fiber-reinforced plastic by the National Standardization Technical Committee (SAC/TC39) centralized. This standard was drafted. Shanghai FRP Research Institute Limited. The main drafters. Zhang Xu, Yao Hui, Zhang Ruguang. Composite inner surface shear performance test method1 ScopeThis standard specifies the fiber reinforced plastic plane shear properties of test equipment, and sample preparation, test conditions, test procedures and results Calculation. This standard applies to the determination symmetrical fiber reinforced plastic laminate shear strength, shear modulus and shear stress - strain curve.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 1446 Test methods for fiber reinforced plastic properties General GB/T 3961 fiber reinforced plastics3 Terms and DefinitionsGB/T 3961 defined by the following terms and definitions apply to this document. 3.1 Residual strain shear strength offsetshearstrength In residual strain tolerance value is set as a starting point to the secant modulus of elasticity is the slope of a straight line, and shear stress - strain curve at the intersection Stress. Note. residual strain shear strength of the material used to determine the stress - strain curve is approximately linear limit, referred to as τS (non-linear curve of this definition included both No material has been found not exclude damage). In the absence of an appropriate basis to determine if the parameter value is set, usually 0.2% engineering strain as Set residual strain tolerance value, the corresponding residual strain shear strength denoted τS (0.2). In comparing the residual strain shear strength of the material must be used The same residual strain tolerance limits, see Figure 1. 3.2 Secant modulus of elasticity chordmodulusofelasticity Shear stress - strain curve, with a little strain as a starting point (Recommendation 0.15% ~ 0.25%), to take the appropriate strain increment [through Often taking (0.4 ± 0.02)%], stress increment it corresponds with the strain increment ratio is the secant modulus of elasticity, which is regarded as the initial elastic modulus Modulus. 3.3 Ultimate shear strength ultimatestrength The maximum shear stress value in the range of 5% shear strain. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 28889-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 28889-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 28889-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 28889-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
