GB/T 26548.7-2020 English PDFUS$344.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 26548.7-2020: Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 7: Nibblers and shears Status: Valid
Basic dataStandard ID: GB/T 26548.7-2020 (GB/T26548.7-2020)Description (Translated English): Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 7: Nibblers and shears Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J48 Classification of International Standard: 13.160; 25.140.10 Word Count Estimation: 18,187 Date of Issue: 2020-11-19 Date of Implementation: 2021-10-01 Regulation (derived from): National Standard Announcement No. 26 of 2020 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 26548.7-2020: Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 7: Nibblers and shears---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Hand-held portable power tools-Test methods for evaluation of vibration emission-Part 7.Nibblers and shears ICS 13.160; 25.140.10 J48 National Standards of People's Republic of China Vibration test method for handheld portable power tools Part 7.Punching machine and scissors 2020-11-19 released 2021-10-01 implementation State Administration for Market Regulation Issued by the National Standardization Management Committee Table of contentsForeword Ⅰ Introduction Ⅱ 1 Scope 1 2 Normative references 1 3 Terms, definitions and symbols 1 4 Basic criteria and vibration test methods 2 5 Description of machine type 2 6 Vibration characteristics description 4 7 Instrument requirements 6 8 Test and operating conditions of the machine 6 9 Measurement procedures and effectiveness of measurement 8 10 Test report 9 Appendix A (informative appendix) Test report format for punching shears and scissors 10 Appendix B (Normative Appendix) Determination of Uncertainty 12 Reference 14ForewordGB/T 26548 "Handheld portable power tools vibration test method" is divided into the following parts. ---Part 1.Angle and face grinders; ---Part 2.Gas trigger, nut wrench and screwdriver; ---Part 3.Polishing machines, rotary, sliding and double polishing machines; ---Part 4.Straight shank grinder; ---Part 5.Drills and impact drills; ---Part 6.Compaction machine; ---Part 7.Punching machine and scissors; ---Part 8.Reciprocating saws, polishing machines and files, and pendulum or rotary saws; ---Part 9.Derusting hammer and needle beam derusting device; --- Part 10.Impact rock drills, hammers and breakers; ---Part 11.Stone Hammer; ---Part 12.Mold grinder; ---Part 13.Fastener drive tools. This part is Part 7 of GB/T 26548. This section was drafted in accordance with the rules given in GB/T 1.1-2009. The translation method used in this part is equivalent to ISO 28927-7.2009 "Hand-held portable power tool vibration test method Part 7. Punching machine and scissors. The Chinese documents that have a consistent correspondence with the international documents cited in this section are as follows. ---GB/T 5621-2008 Rock drilling machinery and pneumatic tools performance test method (ISO 2787.1984, MOD) ---GB/T 6247.1-2013 Terminology for rock drilling machinery and portable power tools Part 1.Rock drilling machinery, pneumatic tools and Pneumatic machinery (ISO 5391.2003, MOD) This section has made the following editorial changes. --- Convert the "bar" in the international standard to "MPa" (1bar=0.1MPa). This part was proposed by China Machinery Industry Federation. This part is under the jurisdiction of the National Standardization Technical Committee for Rock Drilling Machinery and Pneumatic Tools (SAC/TC173). Drafting organizations of this section. Dongguan Institute of Technology, Tianshui Rock Drilling Machinery Pneumatic Tool Research Institute, Taitian Group Co., Ltd., National Pneumatic Products Quality Supervision and Inspection Center, Shaoyang College. The main drafters of this section. Zhou Zirong, Wang Jianzu, Lin Xuejun, Hui Weian, Gan Li.IntroductionThis document is a Type C standard specified in ISO 12100. For machines designed and manufactured in accordance with the requirements of Type C standards, when the requirements of Type C standards are different from those in Type A or Type B standards At the time, the requirements in the C standard are better than other standards. GB/T 25631-2010 gives general technical conditions for handheld and hand-guided mechanical vibration measurement, GB/T 26548 (all parts (Point) Based on this standard, the vibration test method of hand-held portable machines is given, and the operating conditions of the machine under the type test conditions are specified. Parts and other requirements for type test performance. The standard structure and chapter numbering are consistent with GB/T 25631-2010. This part of GB/T 26548 adopts the sensor reference positioning method first adopted in the European series of standards EN60745. The reason for continuity is inconsistent with GB/T 25631-2010 in description. The sensor is preferably placed near the area between the thumb and index finger of the hand Domain, because this position has the least interference to the operator holding the machine. Usually, the vibration produced by the punching machine and the scissors is very different. This difference in vibration characteristics is caused by the machine The characteristics of the material and the difference in supporting materials. In order to provide a method to produce good measurement reproducibility, this part of GB/T 26548 uses the processing of cutting metal sheets. The main reason is that the thin metal plate has good support performance to ensure the good use of the punch and the scissors blade. Assessment of vibration exposure in the workplace Adopt GB/T 14790 (all parts) procedures. The value obtained is the type test value, which is used to represent the average value of the upper quartile of the typical vibration of the machine in actual use. however, Actual values sometimes vary greatly, depending on many factors, including the operator, work tasks, and insertion tools or consumables. The machine itself The maintenance status may also be important. In real working conditions, the impact of operators and operating procedures on low-amplitude vibration is particularly serious. because Therefore, the vibration radiation value below 2.5m/s2 is not recommended for evaluation under real working conditions. In this case, it is recommended to use 2.5m/s2 vibration Momentum value to directly evaluate the vibration of the machine. If precise values are required for a specific workplace, it is necessary to perform the calculation in accordance with GB/T 14790 (all parts) under this working condition. Line measurement. The measured vibration value under actual working conditions may be higher or lower than the value obtained with this section. In actual working conditions, improper support of processing materials or wear of punches and scissors blades are prone to high vibration. Vibration test method for handheld portable power tools Part 7.Punching machine and scissors1 ScopeThis part of GB/T 26548 specifies the test method for hand-transmitted vibration measurement of hand-held power-driven punching and shearing machine and scissors handle. The type inspection procedure for the vibration magnitude of the handle grip part when operating the machine under the specified test conditions is determined. The measured results are used to compare Compared with the vibration level of different models of the same model. This section applies to compressed air or other means to drive, used to cut metal plates or composite material plates punching shears and scissors (see Chapter 5). Note. In order to avoid confusion between "power tools" and "insertion tools", "machines" are used instead of "power tools" throughout this section.2 Normative referencesThe following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this document. For undated references, the latest version (including all amendments) applies to this document. GB/T 6247.2-2013 Rock Drilling Machinery and Portable Power Tools Terminology Part 2.Hydraulic Tools (ISO 17066.2007, IDT) GB/T 14790.1-2009 Mechanical vibration Measurement and evaluation of human exposure to hand-borne vibration Part 1.General requirements (ISO 5349-1.2001, IDT) GB/T 14790.2-2014 Mechanical vibration Measurement and evaluation of human exposure to hand-borne vibration Part 2.Workplace measurement Practical Guide (ISO 5349-2.2001, IDT) GB/T 25631-2010 Mechanical vibration Hand-held and hand-guided mechanical vibration evaluation rules (ISO 20643.2005, IDT) ISO 2787.1984 Rotary and impact pneumatic tools performance test ISO 5391.2003 Pneumatic Tools and Machinery Vocabulary EN12096.1997 Marking and Verification of Radiation Value of Mechanical Vibration 3 Terms, definitions and symbols GB/T 6247.2-2013, GB/T 25631-2010 and ISO 5391.2003 defined and the following terms, definitions and symbols are suitable Used in this document. For ease of use, some terms and definitions in ISO 5391.2003 are listed repeatedly below. 3.1 Terms and definitions 3.1.1 Punching machine A machine in which a punch passes through a fixed die in reciprocating motion to cut sheet metal by punching material. [ISO 5391.2003, definition 2.1.11] ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 26548.7-2020_English be delivered?Answer: Upon your order, we will start to translate GB/T 26548.7-2020_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 26548.7-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 26548.7-2020_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
