GB/T 22587-2017 English PDFUS$414.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 22587-2017: Matrix to superconductor volume ratio measurement -- Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires Status: Valid GB/T 22587: Historical versions
Basic dataStandard ID: GB/T 22587-2017 (GB/T22587-2017)Description (Translated English): Matrix to superconductor volume ratio measurement -- Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H21 Classification of International Standard: 77.040.99 Word Count Estimation: 22,270 Date of Issue: 2017-12-29 Date of Implementation: 2018-04-01 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 22587-2017: Matrix to superconductor volume ratio measurement -- Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires ICS 77.040.99 H21 National Standards of People's Republic of China Replacing GB/T 22587-2008 Matrix and superconductor volume ratio measurement Copper - niobium titanium (Cu/Nb-Ti) composite superconducting wire Copper - ultra [volume] ratio measurement (IEC 61788-5..2013, Superconductivity-Part 5. Matrixtosuperconductor ratio of Cu/Nb-Ticompositesuperconductingwires, IDT) 2017-12-29 published.2018-04-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China China National Standardization Administration released Directory Preface Ⅰ Introduction Ⅱ 1 Scope 1 2 Normative references 1 3 Terms and definitions 1 4 principle 1 5 chemicals 2 6 device 2 7 Measurement Step 2 7.1 The quality of the sample 2 7.2 Remove the insulation coating 2 7.3 Cleaning 2 7.4 Dry 3 7.5 Sample quality measurement and repeated measurements 3 7.6 Dissolution of copper 3 7.7 Nb-Ti wire cleaning and drying 3 7.8 Dissolved sample quality measurement and repeated measurements 3 Repeat the measurement procedure with the second sample Calculation of the result 4 Uncertainty of the test method 4 10 test report 5 10.1 Test sample identification 5 10.2 Copper - Super [volume] ratio report 5 10.3 Test Condition Report 5 Appendix A (Normative) Copper - ultra [volume] ratio --- Copper Quality Method 6 Appendix B (Informative) Based on the Nb-Ti ratio of the density 8 Appendix C (Informative) mechanical removal of insulation coating 9 Appendix D (informative) Secondary corrosion of samples 10 Appendix E (informative) on the uncertainty 11 Appendix F (Informative) Cu/Nb-Ti composite superconducting copper - ultra [volume] ratio of uncertainty of the test method 15 References 19 ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 22587-2008 "matrix and superconductor volume ratio of Cu/Nb-Ti composite superconductor copper - super [volume] ratio Measurement". Compared with GB/T 22587-2008, the main technical changes are as follows. --- With the term "uncertainty" instead of "accuracy" and "accuracy"; --- "Copper dissolved" chapter, delete the original "Note 1" "Note 2", the original "Note 4" into the body; --- Appendix A from Chapter 6 to Chapter 9, an increase of "Overview" "Remove insulation coating, clean, dry" and "repeat with a second sample Process "Chapter 3; --- The title of Appendix B is changed from "Density of Nb-Ti" to "Density based on Nb-Ti ratio", adding the header "Table B.1.1Nb-Ti Density "and revised Note 2; --- Added information appendix E "about uncertainty"; --- Added information Appendix F "Cu/Nb-Ti composite superconducting copper - ultra [volume] ratio of uncertainty of the test method of assessment"; --- Added "reference". This standard uses the translation method identical with IEC 61788-5..2013 (Ed. 2.0) "Superconductivity Part 5. The volume of the substrate and the superconductor Measurement of copper-ultra [volume] ratio of Cu/Nb-Ti composite superconducting wire. The documents of our country that are consistent with the corresponding international documents that are normative references in this standard are as follows. --- GB/T 13811-2003 Electrotechnical terminology Superconductivity (eqvIEC 60050-815..2000) This standard made the following editorial changes. --- Remove the "superconductive Part 5." in the name of this standard in order to be consistent with the existing standard series. Please note that some of this document may be patentable. The issuing agencies of this document do not bear the responsibility of identifying these patents. This standard proposed by the Chinese Academy of Sciences. This standard by the National Superconducting Standardization Technical Committee (SAC/TC265) centralized. This standard was drafted. Western Superconducting Materials Science and Technology Co., Ltd., Institute of Physics, Chinese Academy of Sciences, Northwest Nonferrous Metal Research Institute, Beijing Nonferrous Metal Research Institute, North China Electric Power University. The main drafters of this standard. Feng Ran, Yan Ling Xiao, Li Jie, Zhang Pingxiang, Yan fruit, Zheng Minghui, Wang Yinshun. This standard replaces the standards previously issued as follows. --- GB/T 22587-2008.IntroductionIn composite superconductors, copper - super [volume] ratio is mainly used to calculate the critical current density superconducting wire. The method given in this standard is used Try to provide some information needed to determine the suitability of a particular superconductor. This standard contribute to the quality of Cu/Nb-Ti composite superconducting wire Quantity control, acceptance inspection or pilot study. The standard test method is prerequisite for the known density of Nb-Ti, or known volume fraction of Nb-Ti alloy can be based on Record B to estimate its density. If the Nb-Ti density, volume fraction of the Nb-Ti alloy and/or Nb barrier is unknown, Appendix A provides Another Method for Determining Copper - Ultra [Volume] Ratio in Composite Superconductors. Matrix and superconductor volume ratio measurement Copper - niobium titanium (Cu/Nb-Ti) composite superconducting wire Copper - ultra [volume] ratio measurement1 ScopeThis standard specifies the Cu/Nb-Ti composite superconducting wire copper - ultra [volume] ratio test method. The method and the optional method provided in Appendix A apply to a cross-sectional area of 0.1mm2 ~ 3mm2, Nb-Ti wire diameter of 2μm ~ 200 μm, Cu/Nb-Ti composite superconducting wire with a Cu-ultra [volume] ratio of not less than 0.5. The standard Cu/Nb-Ti composite test conductor with a circular or rectangular cross-section of a single structure. This standard uses nitric acid dissolved copper, The allowable deviations and other specific limitations given by routine tests are given. The Cu/Nb-Ti composite superconducting wire with cross-sectional area, wire diameter and copper-ultra [volume] ratio outside this range can also be measured using this method but Uncertainty will be reduced. In addition, in special cases, the test sample may have a special geometry for conductors outside the specified limits, However, in order to simplify and maintain low uncertainty, this standard does not address such issues. After appropriate amendments, the test method given in this standard can be applied to other composite superconducting wire.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version applies to this article Pieces. For undated references, the latest edition (including all amendments) applies to this document. IEC 60050-815 International Electrotechnical terminology - Part 815. Superconductivity (Internationalelectrotechnical vocabulary-Part 815. Superconductivity)3 Terms and definitionsIEC 60050-815 defined and the following terms and definitions apply to this document. 3.1 Copper - super [volume] than coppertosuperconductorvolumeratio The ratio of the volume of stabilized material copper to the volume of non-copper consisting of Nb-Ti wire and Nb barrier layer.4 principleThe test method is the use of Cu/Nb-Ti composite superconducting wire copper can be dissolved in nitric acid, and Nb-Ti wire and Nb barrier is insoluble in nitrate The nature of the acid. After measuring the quality of the sample, it is immersed in nitric acid solution to dissolve the copper only. The mass of the remaining Nb-Ti wire and Nb barrier layer was then measured. The copper-ultra [volume] ratio is determined using the volume and mass of the initial wire and the quality of the wire. When needed, different proportions of Nb-Ti wire are dense See Appendix B for degrees. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 22587-2017_English be delivered?Answer: Upon your order, we will start to translate GB/T 22587-2017_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 22587-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 22587-2017_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 22587-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 22587-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
