GB/T 22318.1-2023 English PDFUS$604.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 22318.1-2023: Surface acoustic wave (SAW) resonators - Part 1: Generic specification Status: Valid GB/T 22318.1: Historical versions
Basic dataStandard ID: GB/T 22318.1-2023 (GB/T22318.1-2023)Description (Translated English): Surface acoustic wave (SAW) resonators - Part 1: Generic specification Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L21 Classification of International Standard: 31.140 Word Count Estimation: 34,30 Date of Issue: 2023-09-07 Date of Implementation: 2024-01-01 Older Standard (superseded by this standard): GB/T 22318.1-2008 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 22318.1-2023: Surface acoustic wave (SAW) resonators - Part 1: Generic specification---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.ICS 31.140 CCSL21 National Standards of People's Republic of China Replace GB/T 22318.1-2008 surface acoustic wave resonator Part 1.General Specifications Part 1.Generic specification Published on 2023-09-07 2024-01-01 Implementation State Administration for Market Regulation Released by the National Standardization Administration Committee Table of contentsPreface III Introduction IV 1 Scope 1 2 Normative reference documents 1 3 Terms and Definitions 3 3.1 General terminology 3 3.2 Working characteristics 5 4 Priority 12 5 Priority Ratings and Characteristics 12 5.1 Standard nominal frequency value, unit is MHz 12 5.2 Standard operating temperature range, unit is ℃ 13 5.3 Standard value of load capacitance, unit is pF 13 5.4 Standard drive level, unit is mW 13 5.5 Minimum insertion loss standard value, unit is dB 13 5.6 Standard climate environment category 13 5.7 Crash severity level 13 5.8 Vibration severity level 13 5.9 Impact severity level 14 5.10 Leak rate 14 6 flags 14 6.1 Resonator marking 14 6.2 Packaging marking15 7 Quality Assessment Procedure 15 7.1 Initial Manufacturing Phase 15 7.2 Structurally similar components 15 7.3 Subcontracting15 7.4 Assembly components 15 7.5 Manufacturer Approval15 7.6 Approval Process 15 7.7 Capability Approval Process 16 7.8 Approval Procedure16 7.9 Test procedure 17 7.10 Screening requirements17 7.11 Rework and repair17 7.12 Test records demonstrating qualification17 7.13 Release validity period 17 7.14 Release of shipment17 7.15 Parameters 17 not checked 8 Test and measurement procedures17 8.1 General 17 8.2 Test and measurement conditions17 8.3 Visual inspection 18 8.4 Dimensional inspection18 8.5 Single-ended pair resonator measurement method 19 8.6 Double-ended pair resonator measurement method 20 8.7 Mechanical and environmental test procedures 23 8.8 Durability test procedure 27ForewordThis document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1.Structure and Drafting Rules of Standardization Documents" Drafting. This document is Part 1 of GB/T 22318 "Surface Acoustic Wave Resonators". GB/T 22318 has released the following parts. ---Part 1.General specifications; ---Part 2.User Guide. This document replaces GB/T 22318.1-2008 "Surface Acoustic Wave Resonators Part 1-1.General Principles and Standard Values". and Compared with GB/T 22318.1-2008, in addition to structural adjustments and editorial changes, the main technical changes are as follows. ---Added priority (see Chapter 4); ---Added quality assessment procedures (see Chapter 7); ---Added test and measurement procedures (see Chapter 8). This document is equivalent to IEC 61019-1.2004 "Surface Acoustic Wave Resonators Part 1.General Specification". This document reverses the order of Chapter 3 and Chapter 4 of IEC 61019-1.2004. This document has made the following minimal editorial changes. ---3.2.10.2.1 "Maximum admittance (minimum impedance) frequency" fs in the circle in Figure 3 is corrected to fa. Please note that some content in this document may be subject to patents. The publisher of this document assumes no responsibility for identifying patents. This document is proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This document is under the jurisdiction of the National Technical Committee on Standardization of Piezoelectric Devices for Frequency Control and Selection (SAC/TC182). This document was drafted by. China Electronics Technology Group Corporation Twenty-sixth Research Institute, China Electronics Technology Tsing Huaying Electronics Co., Ltd., Wuxi City Haoda Electronics Co., Ltd. The main drafters of this document. Jiang Daojun, Zhu Weijun, Huang Hui. The previous versions of this document and the documents it replaces are as follows. ---First published as GB/T 22318.1-2008 in.2008; ---This is the first revision.IntroductionThe surface acoustic wave resonator standard aims to provide general requirements, quality assessment procedures, and appearance and terminal drawings of surface acoustic wave resonators. The sample is intended to consist of the following three parts. Part 1.General specifications. The purpose is to specify the terms and definitions, classification and characteristics of surface acoustic wave resonators, as well as quality assessment procedures. Part 2.User Guide. The purpose is to give the basic structure and working principle of surface acoustic wave resonators, so as to provide users with reasonable choices. Provide guidance on selecting resonators and meeting usage requirements. Part 3.Standard shape and terminal connections. The purpose is to give the commonly used appearance diagrams and terminal functions of surface acoustic wave resonators. definition. surface acoustic wave resonator Part 1.General Specifications1 ScopeThis document specifies test methods for surface acoustic wave (SAW) resonators used to assess the quality of procurement capability approval procedures or qualification approval procedures. and versatility requirements.2 Normative reference documentsThe contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, the dated quotations For undated referenced documents, only the version corresponding to that date applies to this document; for undated referenced documents, the latest version (including all amendments) applies to this document. Note. GB 3100-1993 International System of Units and its Applications (eqvISO 1000.1992) IEC 60050-561 International Electrotechnical Vocabulary (IEV) Part 561.Piezoelectric devices for frequency control and selection ance) Note. GB/T 2421-2020 Environmental Testing Overview and Guidelines (IEC 60068-1.2013, IDT) Tests-TestsA.Cold) Note. GB/T 2423.1-2008 Environmental testing of electrical and electronic products Part 2.Test methods Test A. Low temperature (IEC 60068-2-1.2007, IDT) Tests-TestsB.Dryheat) Note. GB/T 2423.2-2008 Environmental testing of electrical and electronic products Part 2.Test method Test B. High temperature (IEC 60068-2-2.2007, IDT) Note. GB/T 2423.10-2019 Environmental testing Part 2.Test method Test Fc. Vibration (sinusoidal) (IEC 60068-2-6.2007, IDT) IEC 60068-2-7 Environmental testing Part 2.Test methods Test Ga and guidance. Steady-state acceleration (Environmentaltes- Note. GB/T 2423.15-2008 Environmental testing of electrical and electronic products Part 2.Test methods Test Ga and guidelines. Steady state acceleration (IEC 60068-2-7.1986,IDT) 2.Tests-TestM.Lowairpressure) Note. GB/T 2423.21-2008 Environmental testing of electrical and electronic products Part 2.Test methods Test M. Low pressure (IEC 60068-2-13. 1983,IDT) ...... |
