GB/T 17213.1-2015 English PDFUS$234.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 17213.1-2015: Industrial-process control valves -- Part 1: Control valve terminology and general considerations Status: Valid GB/T 17213.1: Historical versions
Basic dataStandard ID: GB/T 17213.1-2015 (GB/T17213.1-2015)Description (Translated English): Industrial-process control valves -- Part 1: Control valve terminology and general considerations Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: N16 Classification of International Standard: 23.060.40; 25.040.40 Word Count Estimation: 12,178 Date of Issue: 2015-12-10 Date of Implementation: 2016-07-01 Older Standard (superseded by this standard): GB/T 17213.1-1998 Regulation (derived from): National Standard Announcement 2015 No.38 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 17213.1-2015: Industrial-process control valves -- Part 1: Control valve terminology and general considerations---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Industrial-process control valves - Part 1. Control valve terminology and general considerations ICS 23.060.40; 25.040.40 N16 National Standards of People's Republic of China Replacing GB/T 17213.1-1998 Industrial process control valves Part 1. Control valve terminology and general principles Part 1. Controlvalveterminologyandgeneralconsiderations (IEC 60534-1.2005, IDT) Issued on. 2015-12-10 2016-07-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 17213 "Industrial process control valves" is divided into the following sections. --- Part 1. Control valve terminology and general provisions (GB/T 17213.1); --- Part 2-1. Flow capacity installed computing equations for fluid flow under conditions (GB/T 17213.2); --- Part 2-3. Flow capacity - Test procedures (GB/T 17213.9); --- Part 2-4. Flow capacity - Inherent flow characteristics and rangeability (GB/T 17213.10); --- Part 2-5. Flow capacity between the fluid flowing through the recovery stage formula multi-level control valve (GB/T 17213.17); --- Part 3-1. Dimensions two straight ball through the control valve from the flange face and two-way ball valve angle control center of the flange to the flange End face of the spacing (GB/T 17213.3); --- Part 3-2. Dimensions rotary control valve end face (except butterfly) distance (GB/T 17213.11); --- Part 3-3. Dimensions butt-type two-pass straight ball valve from the control terminal (GB/T 17213.12); --- Part 4. Inspection and routine testing (GB/T 17213.4); --- Part 5. Flag (GB/T 17213.5); --- Part 6-1. positioners and control valve actuator connected to the installation details of the positioner mounted on linear actuators of (GB/T 17213.6); --- Part 6-2. positioners and control valve actuator connected to the installation details of the positioner mounted on rotary actuators (GB/T 17213.13); --- Part 7. Control valve data sheets (GB/T 17213.7); --- Part 8-1. Noise considerations - Laboratory measurement within the aerodynamic flow through control valve noise generated (GB/T 17213.8); --- Part 8-2. Noise considerations - Laboratory measurement within the hydrodynamic flow through control valve noise generated (GB/T 17213.14); --- Part 8-3. Noise prediction method (GB/T 17213.15) aerodynamic flow through control valve generated noise considerations; --- Part 8-4. Noise considerations hydrodynamic flow through control valve generated noise prediction method (GB/T 17213.16); --- Part 9. Test procedure step input response measurement (GB/T 17213.18). This section GB/T 17213 Part 1. This section drafted in accordance with GB/T 1.1-2009 given rules. This Part replaces GB/T 17213.1-1998 "Industrial process control valves - Part 1. Control valve terminology and general principles." versus GB/T 17213.1-1998 compared to the main technical changes are as follows. --- 3.1.1 deletes from the original standard definition of the control valve straight trip (see GB/T 17213.1-1998 3.1.1); --- The term "ball valve" to "spherical (angle) valve" and modify the definition (see 3.1.1.3, GB/T 17213.1-1998 The 3.1.1.3); --- Deleted the definition of the original standard 3.1.2 rotary control valves (see GB/T 17213.1-1998 3.1.2); --- Modify the term "ball" is defined, the original standard "spherical segments valve" as a new term "cut the ball valve" (see 3.1.2.1,3.1.2.2, GB/T 17213.1-1998 of 3.1.2.1); --- Modify the term "butterfly" is defined (see 3.1.2.3, GB/T 17213.1-1998 of 3.1.2.2); --- Modify the term "plug" is defined, the original standard "closure member for the eccentric portion of the ball valve" as a new term "Eccentric plug" (see 3.1.2.4,3.1.2.5, GB/T 17213.1-1998 of 3.1.2.3); --- Modify the term "bonnet" is defined (see 3.2.2, GB/T 17213.1-1998 3.2.2); --- Modify the definition of the term "trim" (see 3.2.4, GB/T 17213.1-1998 3.2.4); --- Modify the definition of the term "holder" (see 3.3.2, GB/T 17213.1-1998 3.3.2); --- Modify the term "nominal diameter" (see 4.1, GB/T 17213.1-1998 of 3.2.1.1); --- Increasing the term "nominal pipe diameter" (see 4.3); --- Increasing the term "rank" (see 4.4); --- Modify the term "over-travel" (see 4.5.5, GB/T 17213.1-1998 4.1.5); --- Delete the contents on Av flow coefficient (see 4.6, GB/T 17213.1-1998 4.2); --- Remove the "basic equation to determine the flow coefficient" (see GB/T 17213.1-1998 4.2.1); --- Remove the "flow coefficient Av" method of seeking (see GB/T 17213.1-1998 4.2.2); --- Added "valve nominal diameter and nominal pipe diameter identical" requirement (see 4.6.1, GB/T 17213.1-1998 4.2.3); --- Increasing the terms "mounted Flow Characteristics" (see 4.10); --- Increasing the terms "mounted, adjustable ratio" (see 4.12); --- Modify the term "critical pressure ratio" (see 4.14, GB/T 17213.1-1998 4.8); --- Deleted the original standard Chapter 5, "Design requirements" (see GB/T 17213.1-1998 Chapter 5). This section uses the translation method is equivalent to using IEC 60534-1.2005 "Industrial process control valves - Part 1. Control valve terminology and general principles." Correspondence between the consistency of the standards of international documents and normative references of the following documents. --- GB/T 17213 (all parts) industrial process control valves [IEC 60534 (all parts)] This part is proposed by China Machinery Industry Federation. This part of the country's industrial process control and automation Standardization Technical Committee (SAC/TC124) centralized measurement. This section is responsible for drafting unit. Shanghai Institute of Industrial Automation Instrumentation. Participated in the drafting of this section (in alphabetical order). Emerson Process Management (Tianjin) Valve Co., Ltd., Sichuan-Chongqing adjustment Valve Co., Ltd., Chongqing Shi Zhuang Instrument Co., Ltd., Fuyang South Valve Co., Ltd., Hangzhou Valve Co., Ltd., Shanghai valve special stream Body Control Valve Co., Ltd., Shanghai Automation Instrumentation Shares Automation Instrumentation seven plants, Tianjin proficient control Instrumentation Technology Co. Ltd., Wuxi Intelligent Automation Engineering Co., Wuzhong Instrument Co., Ltd., Zhejiang Australia Cheung Automation Technology Co., Ltd., Zhejiang send Waugh Automation Instrumentation Co., Zhejiang tripartite control valve Co., Ltd., Zhejiang Yongsheng Instrumentation Co., Ltd. Zhejiang Sino-German-controlled valves. The main drafters of this section. Wang Jiong, Li Minghua, Shen Wei, Liao Jianmin, Shen Jian standard, Zhang Shishu, Zhangde Xian, Fan Ping, Cai plus tide, Yang Jianwen, Hank Wang, Gao Qiang, Lin Feng, the soldiers left, Lee its exhibition, Zhang Yongliang, Ba Rong-ming, Chen Yan, Tang Jin Jiang, Li, Zhang Jianwei, Ma Yushan, He Wenguang, Xuchun Liang, Meng little new, Chen Dajun, Cai Kejian, Cai Dongwu. This section was first released in January 1998, this is the first revision. Industrial process control valves Part 1. Control valve terminology and general principles1 ScopeGB/T 17213 in this section gives some of the basic terminology and the use of GB/T 17213 other portions of the guide. This section applies to all types of industrial process control valve (hereinafter referred to as the control valve).2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. IEC 60534 (all parts) industrial process control valves (Industrial-processcontrolvalves)3 Component Terminology3.1 Control valve controlvalve Process control system operated by the power adjusting means of the fluid flow. It consists of actuator and valve. Implementing agencies in accordance with control The system sends a signal system, changing the position of the valve closure member. 3.1.1 Straight stroke control valve controlvalvewithalinearmotionclosuremember 3.1.1.1 Diaphragm diaphragmvalve A flexible closure member and the fluid actuator isolation, and the atmosphere valve for sealing purposes. 3.1.1.2 Valve gatevalve Closure member along the linear motion of the valve seat surface of the valve plate. 3.1.1.3 Spherical (angle) valve globe (angle) valve Direction of movement of the closure member is perpendicular to the plane of the valve seat. 3.1.2 Rotary control valves controlvalvewitharotarymotionclosuremember 3.1.2.1 Ball balvalve Closure member for the ball in the middle of the channel with a valve. Axis spherical Globe valve shaft coincide. 3.1.2.2 Truncated sphere ball segmentedbalvalve Closure member is part of the ball valve. Axis spherical Globe valve shaft coincide. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 17213.1-2015_English be delivered?Answer: Upon your order, we will start to translate GB/T 17213.1-2015_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 17213.1-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 17213.1-2015_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 17213.1-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 17213.1-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
