GB/T 17213.18-2015 PDF EnglishUS$180.00 · In stock · Download in 9 seconds
GB/T 17213.18-2015: Industrial-process control valves -- Part 9: Test procedure for response measurements form step inputs Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 17213.18-2015: Industrial-process control valves -- Part 9: Test procedure for response measurements form step inputs---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT17213.18-2015 GB ICS 23.060.40; 25.040.40 N 16 NATIONAL STANDARD OF THE PEOPLE'S REPUBLIC OF CHINA GB/T 17213.18-2015 / IEC 60534-9.2007 Industrial-process control valves - Part 9.Test procedure for response measurements from step inputs 工业过程控制阀 (IEC 60534-9.2007, IDT) Issued on: DECEMBER 10, 2015 Implemented on: JULY 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 6 2 Normative references... 6 3 Terms and definitions... 7 4 Symbols... 14 5 General test procedures... 15 6 Examples of step response... 19 7 Tests specified for each of three test environments... 20 8 Detailed test procedures... 22 9 Presentation of test results... 28 Annex A (Informative) Sliding friction measurement... 31 Bibliography... 33ForewordGB/T 17213 consists of the following parts, under the general title Industrial-process control valves. - Part 1.Control valve terminology and general considerations (GB/T 17213.1); - Part 2-1.Flow capacity - Sizing equations for fluid flow under installed conditions (GB/T 17213.2); - Part 2-3.Flow capacity - Test procedures (GB/T 17213.9); - Part 2-4.Flow capacity - Section Four. Inherent flow characteristics and rangeability (GB/T 17213.10); - Part 2-5.Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery (GB/T 17213.17); - Part 3-1.Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (GB/T 17213.3); - Part 3-2.Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (GB/T 17213.11); - Part 3-3.Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (GB/T 17213.12); - Part 4.Inspection and routine testing (GB/T 17213.4); - Part 5.Marking (GB/T 17213.5); - Part 6-1.Mounting details for attachment of positioners to control valves - Section 1.Positioner mounting on linear actuators (GB/T 17213.6); - Part 6-2.Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators (GB/T 17213.13); - Part 7.Control valve data sheet (GB/T 17213.7); - Part 8-1.Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves (GB/T 17213.8); - Part 8-2.Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves (GB/T 17213.14); - Part 8-3.Noise considerations - Control valve aerodynamic noise prediction Industrial-process control valves – Part 9.Test procedure for response measurements from step inputs1 ScopeThis Part of GB/T 17213 defines the testing and reporting of the step response of control valves that are used in throttling closed-loop control applications. A control valve consists of the complete, ready-to-use assembly of the control valve body, the actuator, and any required accessories. The most probable accessory is a valve positioner. NOTE. For background, refer to technical report ANSI/ISA-TR75.25.02 [6]1). The object of this Part is to define how to test, measure, and report control valve response characteristics in an open-loop environment. This information can be used for process control applications to determine how well and how fast the control valve responds to the control valve input signal. This Part does not define the acceptable control valve performance for process control nor does it restrict the selection of control valves for any application. If this standard is used for evaluation or acceptance testing, the parties may agree to documented variations from these requirements. The information using the defined test methods is specifically applicable to closed-loop feedback control but may have some application to open-loop control applications. This Part does not address valves used in on-off control service. Tests specified in this Part may not be sufficient to measure the performance required for all applications. Not all control valve applications will require this testing.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. 1) Figures in square brackets refer to the Bibliography. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 17213.18-2015 be delivered?Answer: The full copy PDF of English version of GB/T 17213.18-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 17213.18-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 17213.18-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 17213.18-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 17213.18-2015?A step-by-step guide to download PDF of GB/T 17213.18-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 17213.18-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
