GB/T 14034.2-2023 English PDFUS$1099.00 · In stock
Delivery: <= 7 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 14034.2-2023: Connections for hydraulic fluid power - Metallic tube connectors - Part 2: 37-degree flared connectors Status: Valid
Basic dataStandard ID: GB/T 14034.2-2023 (GB/T14034.2-2023)Description (Translated English): Connections for hydraulic fluid power - Metallic tube connectors - Part 2: 37-degree flared connectors Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J20 Classification of International Standard: 23.100.40 Word Count Estimation: 54,593 Date of Issue: 2023-05-23 Date of Implementation: 2023-12-01 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 14034.2-2023: Connections for hydraulic fluid power - Metallic tube connectors - Part 2: 37-degree flared connectors---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. ICS 23:100:40 CCSJ20 National Standards of People's Republic of China Hydraulic transmission connection metal pipe fittings Part 2: 37° flared Part 2: 37°flared connectors and general use-Part 2: 37°flared connectors, MOD) Released on 2023-05-23 2023-12-01 implementation State Administration for Market Regulation Released by the National Standardization Management Committee table of contentsPreface I Introduction III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 2 4 Material 3 5 Pressure and temperature 3 6 Nomenclature of pipe joints 4 7 metal pipe 6 8 Width across flats and tolerances 7 9 design 8 10 thread 9 11 Manufacturing 9 12 Assembly Guide 10 13 Purchasing Information 10 14 logo 10 15 Performance requirements and qualification test 10 16 Labeling instructions 12 Appendix A (Normative) Length reduction of reducing pipe joints 40 Reference 48forewordThis document is in accordance with the provisions of GB/T 1:1-2020 "Guidelines for Standardization Work Part 1: Structure and Drafting Rules for Standardization Documents" drafting: This document is part 2 of GB/T 14034 "Metal Pipe Fittings for Hydraulic Transmission Connections": GB/T 14034 has issued the following part: --- Part 1: 24° cone; --- Part 2: 37° flared type; --- Part 4: 60 ° cone: This document is modified to adopt ISO 8434-2:2007 "Fluid power and general metal pipe fittings - Part 2: 37° flared pipe joints": Compared with ISO 8434-2:2007, this document has made the following structural adjustments: --- Added "Table 2, Table 8, Table 10, Table 12, Table 14, Table 17, Table 18, Table 20, Table 22, Table 24, Table 26, Table 28, Table 30, Table 32, Table 34", "Table 3~Table 7, Table 9, Table 11, Table 13, Table 15, Table 16, Table 19, Table 21, Table 23, Table 25, Table 27, Table 29, Table 31, Table 33, and Table 35" respectively correspond to "Table 2~Table 20" of ISO 8434-2:2007; --- "Figure 4" has been added, and the numbers of the original "Figure 4" and subsequent figures have been extended; --- "15:1" corresponds to the "15:1 suspension section" of ISO 8434-2:2007, "15:2" is added, and "15:2:1~15:2:5" corresponds to "15:1:1~15:1:5" of ISO 8434-2:2007, "15:2:6" corresponds to "15:2" of ISO 8434-2:2007; --- Added "Table A:1, Table A:3", "Table A:2, Table A:4~Table A:9" corresponding to "Table A:1, Table A:9" of ISO 8434-2:2007 Table A:2~Table A:7": The technical differences between this document and ISO 8434-2:2007 and their reasons are as follows: --- Replaced ISO 5598 (see Chapter 3) with the normatively quoted GB/T 17446 to adapt to my country's technical conditions and improve operability active; --- Changed the terms and definitions (see Chapter 3, Chapter 3 of ISO 8434-2:2007); --- Replaced ISO 6149-3 (see Figure 1, 9:6, Table 26~Table 29, Table A:8) with the normatively quoted GB/T 2878:3 to adapt to my country's technical conditions to improve operability; --- Changed the pressure reduction ratio of stainless steel pipe joints at high temperature (see 5:3, 5:3 of ISO 8434-2:2007) to adapt to the technology of our country condition; --- Replaced ISO 10763 (see 5:8) with the normatively quoted GB/T 41354 to adapt to my country's technical conditions and improve operability active; ---The flared end has increased the metric thread series (see Table 2) to improve operability; --- Deleted the normative references ISO 3304 and ISO 3305 (see 7:3 of ISO 8434-2:2007) to adapt to my country's technical standards technical conditions; --- GB/T 3639 (see 7:3) for normative references has been added to adapt to the technical conditions of our country and improve operability; --- Replaced ISO 4759-1:2000 (see 8:2) with the normatively quoted GB/T 3103:1 to adapt to the technical conditions of our country and improve high operability; --- Added GB/T 196 and GB/T 197 (see 10:1) for normative references to adapt to my country's technical conditions and improve operability active; --- Replaced ISO 263 (see 10:1, 10:2) with the normatively quoted GB/T 20670 to adapt to my country's technical conditions and improve reliability operability; --- Replaced ISO 68-2 (see 10:1) with the normatively quoted GB/T 20669 to adapt to my country's technical conditions and improve reliability operability; --- Replaced ISO 261 (see 10:1, 10:2) with the normatively quoted GB/T 193 to adapt to my country's technical conditions and improve operability active; --- Replaced ISO 228-1:2000 (see 10:2) with the normatively quoted GB/T 7307 to adapt to my country's technical conditions and improve Operability; ---Change "Table 10~Table 14" to "Table 20~Table 29" that the stud end dimensions should comply with (see 10:2, ISO 8434-2:2007 10:2) to adapt to the technical conditions of our country and improve operability; --- Replaced ISO 9227 (see 11:3) with the normatively quoted GB/T 10125 to adapt to my country's technical conditions and improve operability active; --- Changed the requirements for purchasers in "Purchasing Information" (see Chapter 13, Chapter 13 of ISO 8434-2:2007) to adapt to my country technical conditions to improve operability; --- Replaced ISO 19879 (see Chapter 15) with the normatively quoted GB/T 26143 to adapt to my country's technical conditions and improve reliability operability; --- Increased the size of the metric thread series (see Table 7, Table 8, Table 10, etc:) to improve operability; --- Change the thread specification "M33×1:5" to "M33×2" (see Table 27, Table 29, Table 16 and Table 17 of ISO 8434-2:2007), to Adapt to the technical conditions of our country; --- Changed the length reduction value of straight-through variable diameter pipe joints (see Table A:2, Table A:5, Table A:1 and Table A:3 of ISO 8434-2:2007), To adapt to the technical conditions of our country; ---Delete the big end thread specification (see Table A:6 of ISO 8434-2:2007), and increase the thread specification corresponding to the small end (see Table A:8, Table A:9), to adapt to my country's technical conditions: The following editorial changes have also been made to this document: --- Change the name of the standard to "Metal Pipe Fittings for Hydraulic Transmission Connections Part 2: 37° Flare Type"; --- Added Note 3 and Note 4 (see Chapter 1); --- Changed the list of normative references; --- Deleted the pressure unit "bar" in the chart; --- Added "Figure 4 Schematic diagram of width across sides, diagonal dimensions, and side plane length"; --- Replaced ISO 6149-1 with the informative referenced GB/T 2878:1, and adjusted to the references; --- Replaced ISO 12151-5 with the informative referenced GB/T 9065:5; ---ISO 1179-1, ISO 1179-2, ISO 1179-4, ISO 9974-1, ISO 9974-3, ISO 11926-1 that will be cited for information Adjust to references; --- Deleted the informative reference to ISO 5864:1993: Please note that some contents of this document may refer to patents: The issuing agency of this document assumes no responsibility for identifying patents: This document is proposed by China Machinery Industry Federation: This document is under the jurisdiction of the National Hydraulic Pneumatic Standardization Technical Committee (SAC/TC3): This document is drafted by: Zhejiang Suqiangge Hydraulic Co:, Ltd:, Zhejiang Songqiao Pneumatic Hydraulic Co:, Ltd:, Bengbu Hydraulic Machinery Co:, Ltd: Company, Ningbo Jiurong Hydraulic Equipment Co:, Ltd:, Xiamen Meike Security Technology Co:, Ltd:, Ningbo Guyuan Pipe Fittings Co:, Ltd:, Sichuan Chuanrun Hydraulic Lubricating Equipment Co:, Ltd:, Zhejiang Higway Hydraulic Technology Co:, Ltd:, Eaton Hydraulics (Ningbo) Co:, Ltd:, Tianjin Jingyan Engineering Machinery Mechanical Transmission Co:, Ltd:, Guangdong Hengxinya Technology Co:, Ltd:, Guangdong Tianheng Hydraulic Machinery Co:, Ltd:, Beijing Machinery Industry Automation Research Institute Ltd: The main drafters of this document: Luo Xuerong, Wu Jiegang, Lou Zhongyu, Qian Laohong, Chen Ke, Wang Fengping, Zhang Ke, Yu Dongze, Wang Yongchao, Yu Jijian, Feng Guoxun, Huang Qiongfang, Zhang Fu, Cao Qiaohui:IntroductionGB/T 14034 aims to standardize the technical requirements of metal pipe joints for hydraulic transmission connections, and consists of four parts: --- Part 1: 24 ° cone: The purpose is to identify general design requirements for 24° conical fittings utilizing ferrule or O-ring seals: requirements, basic dimensions, performance requirements and qualification tests: --- Part 2: 37 ° flared: The purpose is to determine the 37°flared pipe connection suitable for metal pipes with an outer diameter of 6mm~50:8mm General design requirements, basic dimensions, performance requirements and qualification tests for head design: --- Part 3: End face seals: The purpose is to determine the general design requirements, basic dimensions, performance requirements and and qualification tests: --- Part 4: 60 ° cone: The purpose is to determine whether it is suitable for metal pipes with an outer diameter of 6mm~50mm or an inner diameter of 5mm~ General design requirements, basic dimensions, performance requirements and qualification tests for 60° tapered pipe joints for 51mm hoses: Hydraulic transmission connection metal pipe fittings Part 2: 37° flared1 ScopeThis document specifies the general design requirements and basic dimensions for 37° flared pipe joints applicable to metal pipes with an outer diameter of 6 mm to 50:8 mm: Dimensional and performance requirements, as well as qualification tests, flared fittings are used for fluid transmission within the pressure and temperature ranges specified in this document and general applications: The pipe joints specified in this document are suitable for connecting metal pipes or hose joints with those in accordance with GB/T 2878:1, ISO 9974-1, ISO 1179-1 or The oil port of ISO 11926-1 is used for transition connection (refer to GB/T 9065:5 for relevant hose joint specifications): Note 1: For new application design, relevant requirements are given in 9:6: Where elastomeric seals are permitted, national standards and inclusion of elastomeric seals are preferred pipe joint design: Note 2: Use under conditions outside the specified pressure and temperature ranges, see 5:5: Note 3: Metric threaded flare ends and metric metal tubing are preferred: For unified thread flare ends, both metric and imperial pipes are applicable (see Figure 8), just change Just change the bushing: Note 4: This type of pipe joint works under the working pressure given in Table 1, and realizes full flow connection through metal-to-metal sealing: due to many factors These values cannot be regarded as minimum guaranteed values: For each application, both the supplier and the purchaser need to conduct sufficient tests and evaluate the results: A review is performed to ensure that the fittings meet the required performance levels:2 Normative referencesThe contents of the following documents constitute the essential provisions of this document through normative references in the text: Among them, dated references For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document: GB/T 193 Common thread diameter and pitch series (GB/T 193-2003, ISO 261:1998, MOD) GB/T 196 Common thread basic dimensions (GB/T 196-2003, ISO 724:1993, MOD) GB/T 197 Common thread tolerances (GB/T 197-2018, ISO 965-1:2013, MOD) GB/T 2878:3 Hydraulic power connections with metric thread and O-ring seals on ports and stud ends - Part 3: Lightweight studs Terminal (L series) (GB/T 2878:3-2017, ISO 6149-3:2006, MOD) GB/T 3103:1 Fastener tolerances for bolts, screws, studs and nuts (GB/T 3103:1-2002, idtISO 4759-1:2000) GB/T 3639 cold-drawn or cold-rolled precision seamless steel tubes GB/T 7307 55°unsealed pipe thread (GB/T 7307-2001, eqvISO 228-1:1994) GB/T 10125 Artificial atmosphere corrosion test Salt spray test (GB/T 10125-2021, ISO 9227:2017, MOD) GB/T 17446 Vocabulary for fluid transmission systems and components (GB/T 17446-2012, ISO 5598:2008, IDT) GB/T 20669 unified thread profile (GB/T 20669-2006, ISO 68-2:1998, MOD) GB/T 20670 Unified thread diameter and thread number series (GB/T 20670-2006, ISO 263:1973, MOD) GB/T 26143 Test method for hydraulic pipe joints (GB/T 26143-2010, ISO 19879:2010, IDT) GB/T 41354 Dimensions and nominal pressure of seamless or welded flat-ended precision steel pipes for hydraulic transmission (GB/T 41354-2022, ISO 10763:2020, MOD) ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 14034.2-2023_English be delivered?Answer: Upon your order, we will start to translate GB/T 14034.2-2023_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 7 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 14034.2-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14034.2-2023_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
