FZ/T 93030-2007 English PDF

US$169.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
FZ/T 93030-2007: Textile machinery and accessories. Cones for cross winding. Technology terms
Status: Valid

FZ/T 93030: Historical versions

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
FZ/T 93030-2007	169	Add to Cart	3 days	Textile machinery and accessories. Cones for cross winding. Technology terms	Valid
FZ/T 93030-1994	519	Add to Cart	4 days	Winder with Cross-wound Conical Tube	Obsolete

Similar standards

FZ/T 93048.1   FZ/T 93019   FZ/T 93038   FZ/T 93036   FZ/T 93034   

Basic data

Standard ID: FZ/T 93030-2007 (FZ/T93030-2007)
Description (Translated English): Textile machinery and accessories. Cones for cross winding. Technology terms
Sector / Industry: Spinning & Textile Industry Standard (Recommended)
Classification of Chinese Standard: W93
Classification of International Standard: 59.120.10
Word Count Estimation: 6,626
Date of Issue: 2007-05-29
Date of Implementation: 2007-11-01
Older Standard (superseded by this standard): FZ/T 93030-1994
Quoted Standard: GB/T 191; GB/T 1958; GB/T 2828.1; GB/T 2829; GB/T 4892; GB/T 6543-1986; GB/T 6544-1999; GB/T 20035.1-2005; GB/T 20035.2-2005; GB/T 20035.3-2005; GB/T 20035.5-2005
Regulation (derived from): NDRC Notice No. 32 of 2007
Issuing agency(ies): National Development and Reform Commission of the People's Republic of China
Summary: This standard specifies the conical cross-wound bobbin with the requirements, test methods, inspection rules, packaging and identification. This standard applies to half cone angle of 3 �� 30 ', 4 �� 20', 5 �� 57 ', the winding width not exceeding l-25mm with a conical cross- wound bobbin (hereinafter referred to as " conical tube ").

FZ/T 93030-2007: Textile machinery and accessories. Cones for cross winding. Technology terms

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Textile machinery and accessories. Cones for cross winding. Technology terms ICS 59.120.10 W93 People's Republic of China textile industry standards Replacing FZ/T 93030-1994 Textile machinery and accessories With conical cross-wound bobbin technical conditions Posted 2007-05-29 2007-11-01 implementation National Development and Reform Commission, People's Republic of China released

Foreword

Instead of the standard FZ/T 93030-1994 "cross winding winder with conical tubes" in the part, not in place of covering cross Main dimensions fork with conical winding bobbin, tolerances and marking. GB/T 20035-2005 is half cone angle of 3 ° 30 ', 4 ° 20' and 5 ° 57 'cross Fork with conical winding bobbin dimensions, tolerances and the national standards. Cross winding included with main dimensions recommended values cone bobbin GB/T 20035 Part 1, its dimensions, tolerances and marking according to different half cone angle are included in Part 2 GB/T 20035 of ~ Part 5, are listed below international standards and the structure of the national standard corresponding to. GB/T 20035-2005 "Textile machinery and accessories with a conical cross-wound bobbin" --- Part 1. Recommended main dimensions value (ISO 8489-1.1995, IDT); --- Part 2. half cone angle of 3 ° 30 'cone bobbin dimensions, tolerances and marking (ISO 8489-2.1995, IDT); --- Part 3. half cone angle of 4 ° 20 'cone bobbin dimensions, tolerances and marking (ISO 8489-3.1995, IDT); --- Part 4. half cone angle of 4 ° 20 'stained with conical bobbin dimensions, tolerances and marking (ISO 8489-4.1995, IDT); --- Part 5. half-cone angle of 5 ° 57 'cone bobbin dimensions, tolerances and marking (ISO 8489-5.1995, IDT). Compared with this standard FZ/T 93030-1994, the main changes are as follows. a) by deleting the half cone angle of 9 ° 15 'cone bobbin size and gauge its provisions; b) by deleting according to the pipe material, the small end of the structure, classification provisions of the semi-cone angle conical tube and associated Figs. 1 to 8 and Table 1 ~ Table 3; c) the deletion of the "mark of the tapered tube method" requirement; d) increase "substantially conical tube size, limit deviations" and its measuring "gauge dimensions, tolerances and the use of" should be consistent GB/T 20035.2-2005, GB/T 20035.3-2005, GB/T 20035.5-2005 provisions of Chapter 5; e) In the inspection rules, add "There is one or more than one failure, is substandard goods," the decision rule; f) In the inspection rules, add "In a sample of units" description; g) In the inspection rules, the type of test items to increase the quality of testing, the substandard quality level of 20, classified as substandard C; h) by deleting the chapter on packaging box predetermined and packaging Pictorial marking tied; i) by deleting "Appendix A inner diameter measuring method"; j) other necessary editorial changes. The standard proposed by China Textile Industry Association. This standard by the National Standardization Technical Committee Textile machinery and accessories. This standard by the Shaanxi Institute of Textile Equipment, Zhejiang Sanyou Plastic Industry Co., Ltd. is responsible for drafting. The main drafters of this standard. Zhao Yusheng, water conservancy Hou, Zhang Nan, Jiangchuan Liang. This standard replaces the standards previously issued as follows. --- FJ1023-1981, FJ1127-1981; --- FZ/T 93030-1994. Textile machinery and accessories With conical cross-wound bobbin technical conditions

1 Scope

This standard specifies the conical cross-wound bobbin with the requirements, test methods, inspection rules, packaging and identification. (Hereinafter referred to as "tapered pipe").

2 Normative references

The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB/T 191 Packaging - Pictorial signs GB/T 1958 Geometrical Product Specifications (GPS) shape and position tolerance testing requirements GB/T 2828.1 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch inspection sampling plan (ISO 2859-1.1999, IDT) GB/T 2829 periodic inspection Sampling procedures and tables (suitable for process stability test) GB/T 4892 hard straight cube transport packaging size series GB/T 6543-1986 corrugated boxes GB/T 6544-1999 corrugated cardboard packaging material GB/T 20035.1-2005 Textile machinery and accessories with a conical cross-wound tubes - Part 1. Recommended main dimensions value (ISO 8489-1.1995, IDT) GB/T 20035.2-2005 Textile machinery and accessories with a conical cross-wound tubes - Part 2. half cone angle of 3 ° 30 'cone Shaped bobbin dimensions, tolerances and marking (ISO 8489-2.1995, IDT) GB/T 20035.3-2005 Textile machinery and accessories with a conical cross-wound tubes - Part 3. half cone angle of 4 ° 20 'cone Shaped bobbin dimensions, tolerances and marking (ISO 8489-3.1995, IDT) GB/T 20035.5-2005 Textile machinery and accessories with a conical cross-wound tubes - Part 5. half-cone angle of 5 ° 57 'cone Shaped bobbin dimensions, tolerances and marking (ISO 8489-5.1995, IDT)

3 Requirements

The basic dimensions of 3.1 conical tube, limit deviations shall comply with GB T 20035.1 ~ 20035.3-2005, GB/T 20035.5-2005 provisions /. 3.2 conical oblique tube runout should be specified in Figure 1. NOTE. α/2 of 3 ° 30 ', 4 ° 20', 5 ° 57 '. Figure 1 obliquely conical tube runout ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of FZ/T 93030-2007_English be delivered?

Answer: Upon your order, we will start to translate FZ/T 93030-2007_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of FZ/T 93030-2007_English with my colleagues?

Answer: Yes. The purchased PDF of FZ/T 93030-2007_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.

Question 5: Should I purchase the latest version FZ/T 93030-2007?

Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 93030-2007 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.