FZ/T 01006-2008 English PDFUS$199.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. FZ/T 01006-2008: Coated fabrics. Determination of the coating thickness Status: Valid FZ/T 01006: Historical versions
Basic dataStandard ID: FZ/T 01006-2008 (FZ/T01006-2008)Description (Translated English): Coated fabrics. Determination of the coating thickness Sector / Industry: Spinning & Textile Industry Standard (Recommended) Classification of Chinese Standard: W04 Classification of International Standard: 59.080.40 Word Count Estimation: 8,833 Date of Issue: 2008-04-23 Date of Implementation: 2008-10-01 Older Standard (superseded by this standard): FZ/T 01006-1991 Quoted Standard: GB 6529 Regulation (derived from): NDRC Notice No. 28 of 2008 Issuing agency(ies): National Development and Reform Commission of the People's Republic of China Summary: This standard specifies the coated fabric with a microscope in coating thickness measurement method. This standard applies to the determination of various types of coated fabric layers in the coating thickness. FZ/T 01006-2008: Coated fabrics. Determination of the coating thickness---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Coated fabrics.Determination of the coating thickness ICS 59.080.40 W04 People's Republic of China textile industry standards Replacing FZ/T 01006-1991 Coated fabric coating thickness measurement Posted 2008-04-23 2008-10-01 implementation National Development and Reform Commission, People's Republic of China released ForewordThis standard is the FZ/T 01006-1991 "coated fabric coating thickness test" amendments. And FZ/T 01006-1991 Compared to the main changes are as follows. 1. Increase the reference standard GB 6529; 2. Increasing the English term; 3. The number of samples from one direction to three vertical and horizontal three each; 4. Increasing the arbitration test sample should be adjusted or special performance requirements for wet samples; 5.18 distribution measurement by 3 × 2 × 3 measurements of each sample to 3.00; 6. Added "sample sections to include the full warp buckling wave" requirement; 7. An increase of measuring the maximum thickness of the adhesive is described; 8. Deleted "When the coefficient of variation greater than 25%, resample retest once"; 9. Increased "coefficient of variation C Vp value, if necessary, to calculate the measured values"; 10. The result value "rounding interval 10-3" to "reserved two significant figures"; 11. The original Appendix 2 (Supplementary) combined adjusted to an informative appendix; 12. Increasing the coating thickness measurement schematic site. From the date of implementation of this standard, instead of FZ/T 01006-1991. Appendix A of this standard is an informative annex. The standard proposed by China Textile Industry Association. This standard by the National Standardization Technical Committee based textile branch (SAC/TC209/SC1) centralized. This standard is drafted by. National Textile Products Quality Supervision and Inspection Center. The main drafters of this standard. Wang Jun. This standard was first published in 1991, this revision is the first time. Coated fabric coating thickness measurement1 ScopeThis standard specifies the method for measuring microscopic coating fabric coating thickness. This standard applies to all types of measuring coating thickness of the coating layers of fabric.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB 6529 textiles conditioning and testing - Standard atmospheres GB/T 8170 numerical rounding rules3 Terms and DefinitionsThe following terms and definitions apply to this standard. 3.1 The thickness of the coated surface of fabric layer coating material. The coating may be one or multiple layers (e.g., skin, the foam layer, the light-shielding layer, etc. Various coating). 3.2 Surface coating thickness ginning process by processing coated fabric pattern of recess. 3.3 Cortical thickness of the adhesive layer and the adhesive base cloth. 3.4 By coating the fabric is bonded with adhesive coated surface infiltration distance Ruji Bu deepest point. Principle 4 Under specified conditions, measured with a microscope coated fabric slice thickness of the coating layers. 5 instruments, appliances and materials 5.1 Microscope Magnification. 40,100,250,400. Eyepiece Specifications. × 10, graduated scale scale is 100. Objective standard. × 4, × 10, × 25, × 40. Stage micrometer. for checking magnification, dividing the value of at least 0.01mm. 5.2 folder knife, chopping boards. Can hinge type slicer pole and wooden cutting boards, see Appendix A. 5.3 double-sided blade. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of FZ/T 01006-2008_English be delivered?Answer: Upon your order, we will start to translate FZ/T 01006-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of FZ/T 01006-2008_English with my colleagues?Answer: Yes. The purchased PDF of FZ/T 01006-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version FZ/T 01006-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 01006-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
