GB/T 41875-2022 PDF in English
GB/T 41875-2022 (GB/T41875-2022, GBT 41875-2022, GBT41875-2022)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
GB/T 41875-2022 | English | 170 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Seamless thin-wall molybdenum tubes
| Valid |
Standards related to (historical): GB/T 41875-2022
PDF Preview
GB/T 41875-2022: PDF in English (GBT 41875-2022) GB/T 41875-2022
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.150.99
CCS H 63
Seamless thin-wall molybdenum tubes
无缝薄壁钼管
ISSUED ON: OCTOBER 12, 2022
IMPLEMENTED ON: MAY 1, 2023
Issued by: State Administration for Market Regulation;
Standardization Administration of the PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Classification and marking ... 4
5 Technical requirements ... 5
6 Test methods ... 8
7 Inspection rules ... 8
8 Marking, packaging, transportation, storage, and accompanying documents
... 10
9 Content of order form ... 12
Seamless thin-wall molybdenum tubes
1 Scope
This document specifies the classification and marking, technical requirements, test
methods, inspection rules, marking, packaging, transportation, storage, accompanying
documents, and order form content of seamless thin-wall molybdenum tubes.
This document is applicable to seamless thin-wall molybdenum and molybdenum-alloy
tubes with a wall thickness not greater than 1.5 mm produced by pressure processing.
They are mainly used as nuclear cladding tubes, heat tubes, high-temperature fuel
protection tubes, draft tubes, tubular electrodes, thermocouple protection tubes, and
high-temperature furnace components, etc.
2 Normative references
The contents of the following documents, through normative references in this text,
constitute indispensable provisions of this document. Among them, for dated references,
only the edition corresponding to that date applies to this document. For undated
references, the latest edition (including all amendments) applies to this document.
GB/T 228.1 Metallic materials - Tensile testing - Part 1: Method of test at room
temperature
GB/T 241 Metal materials - Tube - Hydrostatic pressure test
GB/T 1031 Geometrical product specifications (GPS) - Surface texture: Profile
method - Surface roughness parameters and their values
GB/T 4325 (all parts) Methods for chemical analysis of molybdenum
3 Terms and definitions
This document does not have terms and definitions that need to be defined.
4 Classification and marking
4.1 Product classification
Products are divided into six categories according to chemical composition: MG-Mo,
MG-MoLa, MG-MoCe, MG-MoY, MG-MoW, MG-MoRe.
5.6.3 After acid and alkali washing, the surface of the product shall have a silvery white
metallic luster.
6 Test methods
6.1 The determination of the chemical composition of the product shall be carried out
in accordance with the provisions of GB/T 4325 (all parts). The analysis methods for
elements not included in GB/T 4325 (all parts) shall be determined through consultation
between the supplier and the purchaser.
6.2 The dimensions of the product are measured using measuring tools with
corresponding precision.
6.3 The mechanical properties of the product are determined according to the provisions
of GB/T 228.1.
6.4 The hydrostatic pressure test of the product shall be carried out according to the
provisions of GB/T 241.
6.5 The surface roughness of the product shall be measured according to the provisions
of GB/T 1031; or determined through consultation between the supplier and the
purchaser.
6.6 The appearance quality of the product shall be inspected visually.
7 Inspection rules
7.1 Inspection and acceptance
7.1.1 The product shall be inspected by the supplier or a third party, to ensure that the
product quality complies with the provisions of this document and the order form.
7.1.2 The purchaser can inspect the received products according to the provisions of
this document. If the inspection results are inconsistent with the provisions of this
document and the order form, it shall be submitted to the supplier in written form; the
supplier and the purchaser shall negotiate to resolve it. Objections pertaining to
appearance quality shall be raised within one month from the date of receipt of the
product. Objections pertaining to other performances shall be raised within three
months from the date of receipt of the product. If arbitration is required, it shall be
determined by consultation or sampling made jointly by both parties at the purchaser
place.
7.2 Lot grouping
Products shall be submitted for acceptance in lots. Each lot consists of products of the
7.5.5 If the surface roughness does not meet the requirements of this document, it is
allowed to take double number of samples to repeat the test. If any result of the repeated
test is nonconformity, this lot of products shall be judged as nonconformity.
7.5.6 If the appearance quality does not meet the requirements of this document, the
product shall be judged as nonconformity.
8 Marking, packaging, transportation, storage, and
accompanying documents
8.1 Marking
8.1.1 Product marking
The following marks shall be printed on the products that have passed the inspection:
a) Category;
b) Status;
c) Specification;
d) Lot number.
8.1.2 Package marking
Products shall be packed into boxes. Each box shall be marked with:
a) Supplier name and trademark;
b) Product name and category;
c) There shall be obvious "moisture-proof" signs or words on the packaging;
d) Lot number.
8.2 Packaging, transportation, and storage
8.2.1 Packaging
Products shall be packaged piece by piece. The packaging materials shall be moisture-
proof paper, oil-proof paper, foam paper, or other suitable materials. Place the packaged
products in paper (wooden) boxes one by one; fix them with soft filling materials
around them. If there are special requirements, the packaging method negotiated
between the supplier and the purchaser can be used.
8.2.2 Transportation
When the product is transported, moisture or acidic-alkaline gases shall be prevented.
Bumping is strictly prohibited.
8.2.3 Storage
The storage room shall be dry, ventilated, and free of acid and alkali. The storage period
should not exceed two months.
8.3 Accompanying documents
Each lot of products shall be accompanied by accompanying documents. In addition to
supplier information, product information, number of this document, exit-factory date,
or packaging date, it should include the following contents.
a) Product quality assurance letter; the content is as follows:
Main performance and technical parameters of the product;
Product characteristics (including characteristics of manufacturing process
and raw materials);
Responsibility for product quality;
Quality certification obtained by the product; various analysis and inspection
results with inspection seals of the supplier's technical supervision
department.
b) Product conformity certificate; the content is as follows:
Inspection items and their results or inspection conclusions;
Lot size or lot number;
Inspection date;
Inspector's signature or seal.
c) Inspection reports in the process of product quality control AND finished-product
inspection reports.
d) Product instructions: Correct handling, use, storage methods, etc.
e) Other.
...... Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|