PDF GB/T 33235-2016 English
Search result: GB/T 33235-2016
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 33235-2016 | English | 90 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Hail impact test method of reflective glass mirror for concentrated solar power
| Valid |
PDF Preview: GB/T 33235-2016
GB/T 33235-2016: PDF in English (GBT 33235-2016) GB/T 33235-2016
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 81.040.30
Q 34
Hail impact test method of reflective glass
mirror for concentrated solar power
ISSUED ON. DECEMBER 13, 2016
IMPLEMENTED ON. NOVEMBER 1, 2017
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword . 3
1 Scope .. 4
2 Normative references .. 4
3 Test conditions .. 4
4 Test purposes .. 4
5 Testing devices and apparatus .. 5
6 Sample . 6
7 Test procedure .. 6
8 Expression of results .. 8
9 Test report .. 8
Hail impact test method of reflective glass
mirror for concentrated solar power
1 Scope
This Standard specifies the test conditions, test purposes, test devices and apparatus,
samples, test procedures, expression of results and test reports involved in the hail impact
test of reflective glass mirror for concentrated solar power.
This Standard is applicable to the anti-hail impact performance test of the glass reflective
mirror for the solar photothermal; the anti-hail impact performance tests of the glass
reflective mirror for concentrating photovoltaic and the glass reflective mirror of other types
can refer to this Standard.
2 Normative references
The following documents are essential to the application of this document. For the dated
documents, only the versions with the dates indicated are applicable to this document; for
the undated documents, only the latest version (including all the amendments) are
applicable to this standard.
IEC 61215.2005 Crystalline silicon terrestrial photovoltaic (PV) modules - Design
qualification and type approval
3 Test conditions
Unless otherwise specified, the tests shall be carried out under the following conditions.
- Temperature. 20°C ± 5°C;
- Air pressure. 8.60×104 Pa ~ 1.06×105 Pa;
- Relative humidity. 40% ~ 80%.
4 Test purposes
Verify the ability of the glass reflective mirror to withstand the hail impact.
● The mass shall be in the range of (7.53 ± 0.37) g.
c) Before use, place the ice ball in the storage container for at least 1h.
d) Ensure that all the surface temperature of the launchers which are in contact with the
ice ball shall be close to the room temperature.
e) Use the method of the following procedures to launch 3 times for the simulated target
test; adjust the launcher; let the ice ball’s speed which is measured by the speed
sensor at the range of (23 ± 1.15) m·s-1.
f) Install the sample on the bracket at room temperature; install the sample according
to the actual installation mode; let the lowest point of the sample’s surface be
perpendicular to the launch path of the ice ball.
g) Take the ice ball out of the storage container; place it in the launcher; aim at the
impact position specified in Figure 2 and perform launch. The deviation of the impact
point’s position and the specified position shall not be greater than 10 mm. The time
interval from removing the ice ball out of the container to impact it on the sample
shall not exceed 60s.
h) Check the collision area of the sample; mark the damage condition; record all the
visible impact results.
i) If the sample is not damaged, then repeat the steps of g) and h) for other impact
positions in Figure 2, until all impacts are completed.
8 Expression of results
After each impact, check the collision area of the sample; observe the surface condition
after the impact of the sample; record all the cracks or holes which are visible to the naked
eye.
9 Test report
The test report shall include the following.
a) Adopted standard;
b) Name of the sample;
c) Source of sample;
d) Sample’s size, thickness, structure and impact point;
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|