GB/T 7932-2017 PDF EnglishUS$225.00 · In stock · Download in 9 seconds
GB/T 7932-2017: Pneumatic fluid power -- General rules and safety requirements for systems and their components Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 7932: Historical versions
Similar standardsGB/T 7932-2017: Pneumatic fluid power -- General rules and safety requirements for systems and their components---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT7932-2017 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.100.01 J 20 GB/T 7932-2017 / ISO 4414:2010 Replacing GB/T 7932-2003 Pneumatic Fluid Power – General Rules and Safety Requirements for Systems and Their Components (ISO 4414:2010, IDT) ISSUED ON: JULY 12, 2017 IMPLEMENTED ON: FEBRUARY 01, 2018 Issued by: General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword ... 3 Introduction ... 5 1 Scope ... 6 2 Normative References ... 6 3 Terms and Definitions ... 7 4 List of Significant Hazards ... 8 5 General Rules and Safety Requirements ... 8 6 Verification of Safety Requirements and Acceptance Testing ... 26 7 Information for Use ... 26 8 Identification Statement (Reference to this Standard)... 32 Annex A (Informative) List of Significant Hazards ... 33 Annex B (Informative) Form for Collecting Pneumatic System and Component Data to Ensure Conformance with GB/T 7392 ... 35 Bibliography ... 45ForewordThis Standard was drafted as per the rules specified in GB/T 1.1-2009. This Standard replaced GB/T 7932-2003 Pneumatic Fluid Power - General Rules Relating to Systems. Compared with GB/T 7932-2003, this Standard had the major technical changes as follows besides the editorial modifications: --- Change the name of the standard into Pneumatic Fluid Power - General Rules and Safety Requirements for Systems and Their Components; --- Modify the content of the "Scope" (see Clause 1 of this Edition; Clause 1 of 2003 Edition); --- Modify the content of "Normative References" (see Clause 2 of this Edition; Clause 2 of 2003 Edition); --- Delete partial content of "Terms and Definitions" (3.1, 3.3, 3.4, 3.8, 3.9, 3.10, 3.13 of 2003 Edition); --- Modify the content of "General Rules and Safety Requirements" (see Clause 5 of this Edition; Clause 4~Clause 11 of 2003 Edition); --- Add "Inspection and Acceptance Test of Safety Requirements" (see Clause 6 of this Edition); --- Modify the content of "Information for Use" (see Clause 7 of this Edition; 14.4 of 2003 Edition); --- Delete the "Items that Need to be Negotiated between the Supplier and the Purchaser" and the "Example of Parts List " (Annex A and Annex C of 2003 Edition); --- Modify the "List of Dangerous Situations" and " Information on Pneumatic Systems and Components" (see Annex A and Annex B of this Edition; Annex B and Annex D of 2003 Edition); --- Added "Bibliography" (see Bibliography of this Edition). This Standard uses the translation method to equivalently adopt ISO 4414:2010 Pneumatic Fluid Power - General Rules and Safety Requirements for Systems and Their Components. The Chinese documents that have a consistent correspondence relationship with the international documents normatively cited in this Standard are as follows: --- GB/T 786.1-2009 Fluid Power Systems and Components - Graphic Symbols and Circuit Diagrams - Part 1: Graphic Symbols for Conventional Use and Data- Processing Applications (ISO 1219-1:2006, IDT); --- GB 4208-2008 Degrees of Protection Provided by Enclosure (IP Code) (IEC 60529:2001, IDT); --- GB 16754-2008 Safety of Machinery - Emergency Stop - Principles for Design (ISO 13850:2006, IDT); --- GB/T 17446-2012 Fluid Power Systems and Components – Vocabulary (ISO 5598:2008, IDT); --- GB/T 19670-2005 Safety of Machinery - Prevention of Unexpected Start-up (ISO 14118:2000, MOD); --- GB/T 19671-2005 Safety of Machinery - Two-Hand Control Device - Functional Aspects and Design Principles (ISO 13851:2002, IDT); --- GB/T 32215-2015 Pneumatic Fluid Power - Identification of Ports and control Mechanisms of Control Valves and Other Components (ISO 11727:1999, IDT). This Standard was proposed by China Machinery Industry Federation. This Standard shall be under the jurisdiction of National Technical Committee on Hydropneumatics of Standardization Administration of China (SAC/TC 3). Drafting organization of this Standard: Wuxi Pneumatic Technical Research Institute Co., Ltd. Participating drafting organizations of this Standard: Ningbo Xingjian Space Machinery Co., Ltd.; Zhejiang Easun Pneumatic Science and Technology Co., Ltd.; Ningbo Jiaerling Pneumatic Machinery Co., Ltd.; Fenghua Xingyu Electron Co., Ltd.; National Quality Supervision and Inspection Centre of Pneumatic Products; Ningbo Lida Pneumatic Complete Sets Co., Ltd.; Weihai Bosheng Pneumatics & Hydraulics Co., Ltd.; Ningbo Airtac Automatic Industrial Co., Ltd.; Yantai Future Automatic Equipment Co., Ltd.; Ningbo Sono Manufacturing Co., Ltd.; and Wenzhou Airbest Pneumatics Co., Ltd. Chief drafting staffs of this Standard: Zhang Lianren, Wang Chunli, Gao Zepu, Li Jianguo, Wang Wenkui, Geng Manli, Shan Junbo, Cao Jianbo, Zhang Miaoying, Lu Bo, Xu Wei, Xia Jiayong, Zhang Zhiqing, Fang Qinghua, Chen Zaoyang, Guo Xuejing, Cao Changzhen, Mao Xinqiang, Zhang Youbo, Hu Wenjing, and Zou Xinqiang. The historical editions replaced by this Standard are as follows: --- GB/T 7932-1987, GB/T 7932-2003. Pneumatic Fluid Power – General Rules and Safety Requirements for Systems and Their Components1 ScopeThis Standard specifies general rules and safety requirements for pneumatic fluid power systems and components. It deals with all significant hazards associated with pneumatic fluid power systems and specifies principles to apply in order to avoid those hazards when the systems are put to their intended use. NOTE 1: See Clause 4 and Annex A. The significant hazard noise is incompletely dealt with in this Standard. NOTE 2: Noise emission depends especially on the installation of pneumatic components or systems into machinery. This Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects: a) assembly; b) installation; c) adjustment; d) uninterrupted system operation; e) ease and economy of maintenance and cleaning; f) reliable operation in all intended uses; g) energy efficiency; and h) environment. This Standard does not apply to air compressors and the systems associated with air distribution as typically installed in a factory, including gas bottles and receivers.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this document. GB/T 15706-2012 Safety of Machinery - General Principles for Design - Risk Assessment and Risk Reduction (ISO 12100:2010, IDT) ISO 1219-1 Fluid Power Systems and Components – Graphic Symbols and Circuit Diagrams – Part 1: Graphic Symbols for Conventional Use and Data- Processing Applications ISO 1219-2 Power Systems and Components – Graphic Symbols and Circuit Diagrams – Part 2: Circuit Diagrams ISO 5598 Fluid Power Systems and Components – Vocabulary ISO 11727 Pneumatic Fluid Power – Identification of Ports and Control Mechanisms of Control Valves and Other Components ISO 13850 Safety of Machinery – Emergency Stop – Principles for Design ISO 13851 Safety of Machinery – Two-Hand Control Devices – Functional Aspects and Design Principles ISO 14118 Safety of Machinery – Prevention of unexpected Start-up IEC 60529 Degrees of Protection Provided by Enclosures (IP Code)3 Terms and DefinitionsFor the purposes of this Document, the terms and definitions given in ISO 5598 and GB/T 15706 and the following apply. 3.1 Commissioning Procedure by which a system is formally accepted by the purchaser. 3.2 Emergency control Control function that brings a system to a safe condition. 3.3 Function plate Surface that contains information describing either the performance of a manually operated device (e.g., ON/OFF, forward/reverse, left/right, up/down) or the status of a function performed by the system (e.g., clamp, lift, advance). 3.4 Neutral gas ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 7932-2017 be delivered?Answer: The full copy PDF of English version of GB/T 7932-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 7932-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 7932-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 7932-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 7932-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 7932-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 7932-2017?A step-by-step guide to download PDF of GB/T 7932-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 7932-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
