GB/T 7937-2008 English PDFUS$169.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 7937-2008: Fluid power systems and components -- Connectors and associated components -- Nominal pressures Status: Valid GB/T 7937: Historical versions
Basic dataStandard ID: GB/T 7937-2008 (GB/T7937-2008)Description (Translated English): Fluid power systems and components -- Connectors and associated components -- Nominal pressures Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J20 Classification of International Standard: 23.100.40 Word Count Estimation: 7,778 Date of Issue: 2008-01-14 Date of Implementation: 2008-05-01 Older Standard (superseded by this standard): GB/T 7937-2002 Quoted Standard: GB/T 2346-2003; GB/T 17446 Adopted Standard: ISO 4399-1995, MOD Regulation (derived from): National Standard Approval Announcement 2008 No.1 (Total No.114) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the nominal pressure hydraulic and pneumatic fittings and related components. GB/T 7937-2008: Fluid power systems and components -- Connectors and associated components -- Nominal pressures---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Fluid power systems and components. Connectors and associated components. Nominal pressures ICS 23.100.40 J20 National Standards of People's Republic of China Replacing GB/T 7937-2002 Hydraulic and pneumatic fittings and associated components Nominal pressures (ISO 4399.1995, MOD) Posted 2008-01-14 2008-05-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis revised standard adopts the International Standard ISO 4399.1995 "Fluid power systems and components Connectors and associated components Nominal pressure Power "(in English). This standard adopts ISO 4399.1995, the following changes made. --- With Chapter 2 normative references in adopting international standards in place of the standard corresponding to international standards; --- In Table 1 and related provisions, remove the pressure to "bar" as a unit of equivalent values \u200b\u200band the corresponding description; --- In Table 1, an increase of [21MPa], 80MPa, 100MPa, 125MPa, 160MPa five pressure levels. This standard replaces GB/T 7937-2002 "hydraulic and pneumatic fittings and associated components - Nominal pressures", compare with changes as follows. --- 3.1 nominal definition to read "In order to facilitate identification and indicate fittings and associated components attributable to the pressure of the series, and it refers to Predetermined pressure value. "; --- Table 1 in the second row, second column "63" to "6.3." --- Increase in Table 1. [21MPa], 125MPa, 160MPa three pressure levels. The standard proposed by China Machinery Industry Federation. This standard by the National Standardization Technical Committee of hydraulic and pneumatic (SAC/TC3) centralized. This standard was drafted. Beijing Machinery Industry Automation Research Institute. The main drafters of this standard. Zhaoman Lin, Liu Xinde. This standard replaces the standards previously issued as follows. GB/T 7937-1997, GB/T 7937-2002. Hydraulic and pneumatic fittings and associated components Nominal pressures1 ScopeThis standard specifies the nominal pressure hydraulic and pneumatic fittings and associated components.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB/T 2346-2003 fluid power systems and components - Nominal pressures (ISO 2944.2000, MOD) GB/T 17446 Fluid power systems and components Terminology (GB/T 17446-1998, idt ISO 5598. 1985)3 Terms and DefinitionsGB/T 17446 and established the following terms and definitions apply to this standard. 3.1 For ease of presentation and identification fittings and associated components attributable to the pressure of the series, while the value of its specified pressure. Note. This definition is defined in GB/T 2346-2003 applied the same, and only applies to this standard.4 units4.1 nominal pressure rating shall be, respectively kilopascals (kPa) or megapascals (MPa) represented. 4.2 When not specified, nominal pressure gauge should be considered, namely. relative to atmospheric pressure. 4.3 In addition to the nominal specified in this standard should be GB/T 2346-2003 Select. Nominal 5 Nominal pipe fittings and associated components shall be selected in Table 1. Table 1 Nominal pressures megapascals 4 0.25 [21] 50 160 0.63 6.3 2563 110 31.5 80 1.6 16 [35] 100 2.5 2040125 Note. The square brackets in non-recommended value. 6 Marking explanation (to cite this standard) Determining compliance with the standards, test reports, samples and sales documents using the following instructions. Nominal "fittings and associated components of pressure Force in line with GB/T 7937-2008 "hydraulic and pneumatic fittings and associated components - Nominal pressures" provisions. " ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 7937-2008_English be delivered?Answer: Upon your order, we will start to translate GB/T 7937-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 7937-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 7937-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 7937-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 7937-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |