GB/T 5248-2016 English PDFUS$359.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 5248-2016: Electromagnetic (eddy-current) examination of copper and copper alloy seamless tube Status: Valid GB/T 5248: Historical versions
Basic dataStandard ID: GB/T 5248-2016 (GB/T5248-2016)Description (Translated English): Electromagnetic (eddy-current) examination of copper and copper alloy seamless tube Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H26 Classification of International Standard: 77.120.01 Word Count Estimation: 18,142 Date of Issue: 2016-08-29 Date of Implementation: 2017-07-01 Older Standard (superseded by this standard): GB/T 5248-2008 Regulation (derived from): National Standard Announcement 2016 No.14 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 5248-2016: Electromagnetic (eddy-current) examination of copper and copper alloy seamless tube---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Electromagnetic (eddy-current) examination of copper and copper alloy seamless tube ICS 77.040.99 H26 National Standards of People's Republic of China Replacing GB/T 5248-2008 Copper and copper alloy seamless tube eddy current testing method Electromagnetic (eddy-current) examinationof 2016-08-29 released 2017-07-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China China National Standardization Management Committee released ForewordThis standard is drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 5248-2008 "Copper and copper alloy seamless tube eddy current testing method". Compared with GB/T 5248-2008, the main The technical changes are as follows. - the introduction of "standard penetration depth" of the definition and its calculation, add Appendix D, delete the "wall thickness 0.20mm ~ 6.0mm" specification; --- remove flat bottom hole as a standard artificial defect requirements; --- increase the light pipe and the internal thread of the flaw detection specifications and the corresponding standard artificial defects hole, the size of the vertical U-groove; - a sample tube and its production drawings with on-line inspection of standard artificial defects (see 5.6); - Increased manual detection of rotary flaw detection performance indicators (see 4.6.5 and Table 3); --- clear online testing. daily test to adjust the sensitivity (manual), regular test evaluation performance to manual automatic (dynamic) get on. This standard is proposed by China Nonferrous Metals Industry Association. This standard is owned by the National Committee for the Standardization of Nonferrous Metals (SAC/TC243). This standard drafting unit. China Nonferrous Metals Industry Nondestructive Testing Center, Guilin Lijia Metal Co., Ltd., Beijing Nonferrous Metal Research Research Institute, Zhongluo Luoyang Copper Co., Ltd., Jinlong Precision Copper Group Co., Ltd., Jiangyin Xinhua Hong Copper Co., Ltd., Suzhou Longjun Nondestructive Testing Equipment Co., Ltd., in the color Obert Copper and Aluminum Co., Ltd., Jiangxi Nile Copper Co., Ltd. The main drafters of this standard. Zhang Guangji, Wang Yueming, Xi Guoping, Wang Xiaoyan, Zhang Luncao, Zhang Boan, Zhang Ying, Li Yang, Lou Dongge, Chen Hua, Wang Nan, Wang Xiangdong, Liu Aikui, Qin Liyun, Liu Jinlong, Luo Qiliang, Jiang Yexin, Zhang Xijun. This standard replaced the previous version of the standard release. GB/T 5248-1985, GB/T 5248-1998, GB/T 5248-2008. Copper and copper alloy seamless tube eddy current testing method1 ScopeThis standard specifies the copper and copper alloy seamless pipe through the type and point (rotation) eddy current testing methods, comparative samples, equipment, Procedures and results. This standard applies to the diameter of φ3mm ~ φ160mm straight tube and coil surface and near surface defects of the eddy current testing, flaw detection depth Refer to Appendix D. Other specifications of the pipe can refer to the implementation.2 terms and definitionsThe following terms and definitions apply to this document. 2.1 (Brass) online eddy current testing method on-lineeddycurrenttesting The use of electromagnetic induction in the copper tube surface and near the surface of the principle of eddy current, the production process of the whole plate or the whole volume of the flaw detection method. 2.2 (Brass) off-line eddy current testing method off-lineeddycurrenttesting The use of electromagnetic induction in the copper tube surface and near the surface of the principle of eddy current, the production process of copper alone set the flaw detection process One by one or by root detection method. 2.3 Signal to noise ratio signaltonoiseratio The ratio of the amplitude of the defect signal to the maximum noise signal amplitude at the output of the eddy current detector. 2.4 Zero potential differenceofinduced-potential The difference between the induced voltage formed between the windings by the differential connection of the detection coil. Detection of the coil when the specimen is loaded with zero potential. Detection of the coil when there is no test piece for the no-load zero potential. 2.5 Through the eddy current testing method feed-througheddycurrenttestingmethod A method of eddy current testing using a through vortex detection coil. 2.6 Point eddy current testing method probecoileddycurrenttestingmethod A method of eddy current testing using point vortex detection coil. 2.7 Standard penetration depth standarddepthofpenetration In eddy current testing, the depth at which the eddy current decreases to 1/e (about 37%) of the surface eddy current density is called the standard penetration depth. eddy ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 5248-2016_English be delivered?Answer: Upon your order, we will start to translate GB/T 5248-2016_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 5248-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5248-2016_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 5248-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5248-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
