Home Cart Quotation About-Us
www.ChineseStandard.net
SEARCH

GB/T 40920-2021 PDF English

US$185.00 · In stock · Download in 9 seconds
GB/T 40920-2021: Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing
Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Status: Valid
Standard IDUSDBUY PDFDeliveryStandard Title (Description)Status
GB/T 40920-2021185 Add to Cart Auto, 9 seconds. Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing Valid

Similar standards

GB/T 40927   GB/T 40936   GB/T 40938   GB/T 45368   

GB/T 40920-2021: Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing


---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40920-2021
NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 59.140.30 CCS Y 46 Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing (ISO 11640:2018, MOD) ISSUED ON: OCTOBER 11, 2021 IMPLEMENTED ON: MAY 01, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China.

Table of Contents

Foreword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions... 6 4 Principle ... 6 5 Instruments and materials ... 6 6 Sampling and specimen preparation ... 7 7 Test steps ... 9 8 Precision ... 10 9 Test report ... 10 Annex A (informative) Changes in the structure of this document compared to ISO 11640:2018 ... 11 Annex B (informative) Technical differences between this document and ISO 11640:2018 and their reasons ... 12 Leather - Tests for colour fastness - Colour fastness to cycles of to-and-fro rubbing

1 Scope

This Standard specifies the test method that uses felts to do cycles of to-and-fro rubbing on the leather surface, so as to determine the color fastness to rubbing on leather surfaces. This Standard applies to the test of color fastness to cycles of to-and-fro rubbing on various types of leather surfaces.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 250, Textiles - Tests for colour fastness - Grey scale for assessing change in colour (GB/T 250-2008, ISO105-A02:1993, IDT) GB/T 251, Textiles - Tests for colour fastness - Grey scale for assessing staining (GB/T 251-2008, ISO 105-A03:1993, IDT) GB/T 6151, Textiles - Tests for colour fastness - General principles of testing (GB/T 6151-2016, ISO 105-A01:2010, MOD) GB/T 6682, Water for analytical laboratory use - Specification and test methods (GB/T 6682-2008, ISO 3696:1987, MOD) GB/T 24218.2-2009, Textiles - Test methods for nonwovens - Part 2: Determination of thickness (ISO 9073-2:1995, MOD) GB/T 39364, Leather - Chemical, physical, mechanical and fastness tests - Sampling location (GB/T 39364-2020, ISO2418: 2017, MOD) QB/T 2464.23, Determination Method for Color Fastness of Leather to Perspiration (QB/T 2464.23-1999, eqv ISO 11641:1993) QB/T 2707, Leather - Physical and mechanical tests - Sample preparation and conditioning (QB/T 2707-2018, ISO 2419:2012, MOD) QB/T 2724, Leather - Chemical tests - Determination of pH (QB/T 2724-2018, ISO 4045:2008, MOD)

3 Terms and definitions

There are no terms and definitions that need to be defined in this document.

4 Principle

Under a certain pressure, use a felt that meets the requirements to do the cycles of to- and-fro rubbing on the surface of the leather specimen for a specified number of times. Use the gray sample card to access the staining on the felt surface and the discoloration on the leather surface, respectively. Record any other changes and damage visible to the surface of the specimen.

5 Instruments and materials

5.1 Color fastness to rubbing tester: mainly includes the components specified in 5.1.1~5.1.3; the ones in 5.1.4 are optional. 5.1.1 Test bench, including the following components: a) Horizontal metal platform; b) Fixtures: Fix the leather specimen on the platform. The spacing of the fixtures is about 80mm; c) Stretching device: The leather sample can be stretched by at least 20% in the rubbing direction. 5.1.2 Test column: The mass is (500±25)g. It can move or be fixed. It can move freely in the vertical direction. Main include the following: a) Rubbing head: The size is 15mm×15mm; b) Felt and rubbing head connecting device: The cavity depth shall be (3.9±0.1)mm; c) Weight block: The mass is (500±10) g. After loading, the total mass of the test column is (1000±35) g; d) Adjustment device: It can adjust the test column with rubbing head, so that the test column is brought into horizontal contact with the specimen. 5.1.3 Driving device: It can make the test bench to do the to-and-fro movement. The movement distance is 35mm~40mm. Movement rate (40±2) times/min (record a to- and-fro movement as one time). test requirements of the test column in all directions of the specimen [see 5.1.4a)]. Typically, only one specimen needs to be tested for each test condition (such as air conditioning of specimen and felt, number of rubs). In case of disputes, take samples from different parts to test separately. 6.3 Air conditioning of specimens and felts 6.3.1 Dry specimens and felts Conduct air conditioning on dry specimens and felts as specified in QB/T 2707. 6.3.2 Wet felts 6.3.2.1 Boiling method: Put the felt in deionized water (5.5). Heat to boiling. Keep at a slight boiling until the felt is saturated. Then pour out the hot water. Add cold deionized water. Place still to make the wet felt to cool to room temperature. 6.3.2.2 Vacuum method: Put the felt in a container with deionized water (5.5). Put the container in the vacuum desiccator (5.3). Vacuum to about 5kPa. Maintain 2min. Then release the pressure back to normal pressure. Repeat this process at least 2 times. Since black felt may fade when boiled, wet black felt is prepared by vacuum method. 6.3.2.3 Before use, remove the felt in 6.3.2.1 or 6.3.2.2 from the water. Reduce moisture by squeezing or wiping. Make the water absorption of each piece of felt about 1g. The soaking time of the felt in water shall not exceed 24h. 6.3.3 Wet specimens Immerse the leather specimen in a container containing deionized water (5.5). The specimens must not touch each other. Put the container in the vacuum desiccator (5.3). Vacuum to about 5kPa. Maintain 2min. Then release the pressure back to normal pressure. Repeat this process at least 2 times. Before use, remove the specimen from the water. Use absorbent paper to dry the leather surface. The soaking time of the specimen in water shall not exceed 1h. 6.3.4 Artificial sweat wet felt Immerse the felt in a container containing artificial sweat (5.8). Put the container in the vacuum desiccator (5.3). Conduct repeated evacuation and release of pressure to return to normal pressure operation until the felt is submerged. Before use, remove felt from artificial sweat. Reduce artificial sweat content by squeezing or wiping. Make the absorption of each felt to artificial sweat is about 1g. The soaking time of felt in artificial sweat shall not exceed 24h. NOTE: When performing this procedure, wear suitable gloves to avoid direct contact of the wet felt with the skin.

7 Test steps

7.1 Fix the air-conditioned or humidified specimen on the tester. Stretch 10% in the rubbing direction. If the specimen cannot be stretched by 10%, the stretching degree shall be appropriately reduced or not stretched. If the specimen is still not stable during the rubbing process after being stretched by 10%, continue to fully stretch the specimen until the specimen can remain stable during rubbing. In the latter two cases above, record the tensile condition of the specimen in the test report. 7.2 When testing conventional leather specimens, load the load-bearing block so that the total mass of the test column is (1000±35) g. NOTE: For suede, faux suede, leather and fur, due to its own higher friction, during the test, control the total mass of the test column to be (500±25) g. 7.3 Fix the adjusted or wet-conditioned felt on the rubbing head. Make the test column horizontal contact with the leather specimen. Rub for the specified number of times. After rubbing, lift the test column to remove it from the leather specimen, especially when rubbing with wet felt. 7.4 If necessary, replace with new felt. Reselect the number of rubbings. Use the test column to test other parts of the leather specimen (or a new specimen). 7.5 If the felt pills after the test, it shall be re-tested. If the felt is pilled again after the retest, it shall be noted in the test report. 7.6 Take out the specimen and felt. According to the provisions of 7.7, assess the discoloration of the rubbing area and/or the stain of the felt on the specimen, respectively. Wet specimens and felts shall be dried at room temperature prior to assessment. NOTE 1: For coated leather specimens, before assessing color change, use wool to lightly apply a coat of colorless shoe polish on the leather surface. Similarly, for suede or faux suede (such as velvet or nubuck), use a brush in the direction of the fuzz before assessing. NOTE 2: A colorless wax emulsion shall be used as shoe polish. In some cases, wax emulsions are not suitable. Use only shoe polishes that contain waxes and organic solvents. If shoe polish is used, state in the test report. Indicate the composition and other details of the shoe polish. NOTE 3: For white leather or light-colored leather, use black felt for testing if required by customers. Discoloration of the black felt due to friction during the test may cause a slight discoloration of the leather specimen. There is no need to access the color change of the specimen surface at this time. Use white felt to conduct rubbing test on other parts of the specimen before assessment. 7.7 Under D65 light source that is in accordance with GB/T 6151, use gray sample card ......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Image 1     Image 2     Image 3     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of English version of GB/T 40920-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40920-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.

Question 2: Can I share the purchased PDF of GB/T 40920-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40920-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40920-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.

How to buy and download a true PDF of English version of GB/T 40920-2021?

A step-by-step guide to download PDF of GB/T 40920-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 40920-2021".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3    Steps 4~6    Step 7    Step 8    Step 9