GB/T 39741.2-2021 English PDF

US$184.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 39741.2-2021: Plain bearings - Tolerances - Part 2: Tolerances on geometrical characteristics and surface roughness for shafts and thrust collars
Status: Valid

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
GB/T 39741.2-2021	184	Add to Cart	3 days	Plain bearings - Tolerances - Part 2: Tolerances on geometrical characteristics and surface roughness for shafts and thrust collars	Valid

Similar standards

GB/T 42613   GB/T 39333   GB/T 37677   GB/T 39742   GB/T 39743   GB/T 39741.1   

Basic data

Standard ID: GB/T 39741.2-2021 (GB/T39741.2-2021)
Description (Translated English): Plain bearings - Tolerances - Part 2: Tolerances on geometrical characteristics and surface roughness for shafts and thrust collars
Sector / Industry: National Standard (Recommended)
Classification of Chinese Standard: J12
Word Count Estimation: 10,191
Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration

GB/T 39741.2-2021: Plain bearings - Tolerances - Part 2: Tolerances on geometrical characteristics and surface roughness for shafts and thrust collars

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Plain bearings - Tolerances - Part 2.Tolerances on geometrical characteristics and surface roughness for shafts and thrust collars ICS 21.100.10 J12 National Standards of People's Republic of China Sliding bearing tolerance part 2.shaft and Geometric tolerance and surface roughness of thrust shoulder (ISO 12129-2.2019, Plainbearings-Tolerances-Part 2.Toleranceson Released on 2021-03-09 2021-10-01 implementation State Administration of Market Supervision and Administration Issued by the National Standardization Management Committee

Foreword

GB/T 39741 "Tolerance of Sliding Bearings" consists of the following two parts. ---Part 1.Cooperation; ---Part 2.Geometric tolerances and surface roughness of shaft and thrust shoulder. This part is Part 2 of GB/T 39741. This section was drafted in accordance with the rules given in GB/T 1.1-2009. The translation method used in this part is equivalent to the adoption of ISO 12129-2.2019 ``Tolerance of Sliding Bearings Part 2.Shape and Position of Shaft and Thrust Shoulder Tolerance and surface roughness". The Chinese documents that have a consistent correspondence with the international documents cited in this section are as follows. ---GB/T 27939-2011 Quality control technology and inspection of sliding bearing geometry and material quality characteristics (ISO 12301. 2007, IDT) Compared with ISO 12129-2.2019, this part has made the following editorial changes. --- In the title and text, use "geometric tolerance" instead of "shape and position tolerance", and "geometricalcharacteristics" in the English title "Formandposition". The types of geometric tolerances specified in this section include shape tolerances, directional tolerances, position tolerances, and jumps. Dynamic tolerance (see the latest GPS geometric tolerance classification), the "shape and position tolerance" in the original title cannot cover all the specifications specified in this section Therefore, the title is modified to cover all the technical content of this section. This part was proposed by China Machinery Industry Federation. This part is under the jurisdiction of the National Sliding Bearing Standardization Technical Committee (SAC/TC236). Drafting organizations of this section. China Machinery Productivity Promotion Center, Hunan Chongde Technology Co., Ltd., Shenke Sliding Bearing Co., Ltd., Zhejiang Zhuji Bearing Factory Co., Ltd., Zhejiang Shuangfei Oilless Bearing Co., Ltd., Zhejiang Zhongda Precision Components Co., Ltd., Zhejiang Jiang Changsheng Sliding Bearing Co., Ltd., Lin'an Dongfang Sliding Bearing Co., Ltd., Jiashan Sanfu Sliding Bearing Co., Ltd., Jiaxing Mai Ter Baoxin Machinery Industry Co., Ltd. This part is explained by the National Technical Committee for Standardization of Sliding Bearings. Sliding bearing tolerance part 2.shaft and Geometric tolerance and surface roughness of thrust shoulder

1 Scope

This part of GB/T 39741 specifies the geometric tolerances and surface roughness of the shaft, flange, and thrust shoulder of the sliding bearing unit. This section applies to radial or thrust sliding bearings installed horizontally or vertically, or a combination of the two. This section does not apply to crankshaft sliding bearing units of internal combustion engines.

2 Normative references

The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article Pieces. For undated reference documents, the latest version (including all amendments) is applicable to this document. ISO 12301 Plainbearings-Quality Quality Control Technology and Inspection (Plainbearings-Quality controltechniquesandinspectionofgeometricalandmaterialqualitycharacteristics)

3 Terms and definitions

There are no terms and definitions that need to be defined in this document. The website of the ISO and IEC standardized terminology database is as follows.

4 General

The reliability of the sliding bearing not only depends on the material selection and fit of the bearing, but also depends on the shaft and thrust shoulder of the sliding bearing unit. quality. The accuracy grade range of the sliding bearing is determined according to the minimum lubricating film thickness hmin. It can be obtained by reference to ISO 7902-1, ISO 7902-2 and ISO 7902-3 or through other suitable calculation methods. If calculated If there is a significant difference in the thickness of the lubricating oil film between the radial sliding bearing and the thrust sliding bearing, the journal (parameters t1, t2, t3 and the rough surface of the journal can be adjusted. Roughness) and shoulder (parameter t4, t5 and surface roughness of thrust shoulder) specify different accuracy levels.

5 Dimensions and tolerances

See Figure 1~Figure 4 and Table 1. The picture shows the sliding bearing installed horizontally.

6 Design

In terms of product engineering, the transition part between the radial part and the axial part on the shaft can also be made into a concave shape. Due to the many types of bearing seals, detailed requirements for the bearing seal area cannot be given. The geometric dimensions of the shaft and thrust shoulder and The surface roughness should be compatible with the selected bearing seal.

7 Inspection

The quality characteristic inspection shall be carried out in accordance with the provisions of ISO 12301.

8 mark

Accuracy class 20, with two thrust shoulders at the position of the radial thrust sliding bearing, which can bear the axial double-sided load (B) shaft (see Figure 2) Examples of geometric tolerances and surface roughness markings are as follows. Sliding bearing GB/T 39741.2-B20 If the accuracy grades of the journal and the thrust shoulder are inconsistent, the accuracy grades should be marked in the order of journal/thrust shoulder, example as follows. Sliding bearing GB/T 39741.2-B10/B20 ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 39741.2-2021_English be delivered?

Answer: Upon your order, we will start to translate GB/T 39741.2-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 39741.2-2021_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 39741.2-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.