Home   Cart   Quotation   Policy   About-Us
www.ChineseStandard.net
SEARCH

GB/T 36654-2018 English PDF

US$359.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 36654-2018: RF technical requirements and test methods for 76 GHz vehicle radio equipment
Status: Valid
Standard IDUSDBUY PDFLead-DaysStandard Title (Description)Status
GB/T 36654-2018359 Add to Cart 4 days RF technical requirements and test methods for 76 GHz vehicle radio equipment Valid

Similar standards

GB/T 40025   YD/T 3711   GB/T 32401   GB/T 44183   GB/T 44068   

Basic data

Standard ID: GB/T 36654-2018 (GB/T36654-2018)
Description (Translated English): RF technical requirements and test methods for 76 GHz vehicle radio equipment
Sector / Industry: National Standard (Recommended)
Classification of Chinese Standard: M36
Classification of International Standard: 33.060.20
Word Count Estimation: 18,146
Date of Issue: 2018-09-17
Date of Implementation: 2019-01-01
Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration

GB/T 36654-2018: RF technical requirements and test methods for 76 GHz vehicle radio equipment

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
RF technical requirements and test methods for 76 GHz vehicle radio equipment ICS 33.060.20 M36 National Standards of People's Republic of China 76GHz vehicle radio equipment RF indicator Technical requirements and test methods Published on.2018-09-17 2019-01-01 implementation State market supervision and administration China National Standardization Administration issued

Content

Foreword III 1 Scope 1 2 Normative references 1 3 Terms and definitions, abbreviations 1 3.1 Terms and Definitions 1 3.2 Abbreviations 1 4 Technical requirements 2 4.1 Environmental requirements 2 4.2 RF Technical Requirements 2 5 Test Method 3 5.1 Environmental conditions required for testing 3 5.2 Test results and uncertainty 3 5.3 Test Configuration 4 5.4 Peak equivalent isotropic radiation power 5 5.5 Frequency range 6 5.6 Out-of-band emission 6 5.7 Occupied bandwidth 6 5.8 Transmitter spurious emissions 7 5.9 Receiver spurious emissions 8 Appendix A (Normative) Test Site for Radiation Testing 9 Appendix B (Normative) General Test Method for Radiated Spurs 11 Reference 13

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009. Please note that some of the contents of this document may involve patents. The issuing organization of this document is not responsible for identifying these patents. This standard was proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This standard is under the jurisdiction of the National Communications Standardization Technical Committee (SAC/TC485). This standard was drafted. National Radio Monitoring Center Testing Center. The main drafters of this standard. Lin Lei, Feng Shaoqi, Chen Guocheng, Fu Jing, Li Meimei, Liu Xiaoyong, Wang Junfeng, Tao Hongbo, Jiang Qiuhong, Zhang Junchi, Janda. 76GHz vehicle radio equipment RF indicator Technical requirements and test methods

1 Scope

This standard specifies the equivalent omnidirectional radiated power, transmitter spurious emissions, and reception of vehicle radio equipment operating in the 76 GHz band. Technical requirements and test methods for RF indicators such as spurious emissions and out-of-band emissions. This standard applies to vehicle radio equipment operating in the frequency range of 76 GHz to 77 GHz.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 9254-2008 Radio disturbance limits and measurement methods for information technology equipment 3 terms and definitions, abbreviations 3.1 Terms and definitions The following terms and definitions apply to this document. 3.1.1 Equivalent isotropic radiation power equivalentisotropicradiatedpower;EIRP The product of the power output to the antenna in the specified direction relative to the antenna gain of the omnidirectional antenna. 3.1.2 Power spectral density spectralpowerdensity The value of the average equivalent isotropic radiated power per unit bandwidth. 3.1.3 Duty cycle dutycycle The ratio of the duration of a positive pulse to the total period of a pulse in a series of pulse trains. 3.1.4 Spurious emission spuriousemission Unwanted emissions of equipment in the spurious domain. 3.2 Abbreviations The following abbreviations apply to this document. RBW. Resolution Bandwidth (ResolutionBandwidth) RMS. Root Mean Square (RootMeanSquare) VBW. Video Bandwidth (VideoBandwidth)

4 Technical requirements

4.1 Environmental requirements The equipment manufacturer shall state in advance the environmental conditions in which the equipment is to be operated, and the equipment shall operate under its nominal working environment. 4.2 RF technical requirements 4.2.1 Peak equivalent isotropic radiation power 4.2.1.1 Overview The product of the peak power output to the antenna in the specified direction relative to the antenna gain of the omnidirectional antenna. 4.2.1.2 Limits The transmitter operates at the maximum power level. The peak equivalent isotropic radiation power limit is 55 dBm. 4.2.2 Frequency range When the transmitter is operating at the maximum power level. The frequency range of use is 76 GHz to 77 GHz. 4.2.3 Out-of-band emission 4.2.3.1 Overview The out-of-band emission in this standard refers to the maximum power of the transmitter in the frequency range 73.5GHz~76GHz and 77GHz~79.5GHz. Rate spectral density. 4.2.3.2 Limits The out-of-band emission limit is 0dBm/MHz. 4.2.4 Transmitter spurious emissions 4.2.4.1 Overview Transmitter spurious emissions are unwanted emissions in the spurious domain when the device is in the transmitting state. 4.2.4.2 Limits The transmitter spurious limits are shown in Table 1. Table 1 Transmitter spurious emission limits Frequency Range Emission state limit dBm Transmitter standby or idle state dBm Test bandwidth 30MHz≤f< 48.5MHz 48.5MHz≤f≤72.5MHz 72.5MHz \u003cf\u003c76MHz 76MHz≤f≤108MHz -36 -54 -36 -54 -47 100kHz 100kHz 100kHz 100kHz Table 1 (continued) Frequency Range Emission state limit dBm Transmitter standby or idle state dBm Test bandwidth 108MHz \u003cf\u003c167MHz 167MHz≤f≤223MHz 223MHz \u003cf\u003c470MHz 470MHz≤f≤566MHz 566MHz \u003cf\u003c606MHz 606MHz≤f≤798MHz 798MHz \u003cf≤1GHz 1GHz \u003cf≤40GHz f >40GHz -36 -54 -36 -54 -36 -54 -36 -30 -20 -47 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 1MHz 1MHz Note. f represents the transmitter spurious frequency. 4.2.5 Receiver spurious emissions 4.2.5.1 Overview Receiver spurious emissions are unwanted emissions in the spurious domain when the device is in the receiving state. 4.2.5.2 Limits Receiver spurious limits are shown in Table 2. Table 2 Receiver spurious emission limits Frequency Range Limit dBm Test bandwidth 30MHz≤f≤1GHz -57 100kHz f >1GHz -47 1MHz Note. f represents the transmitter spurious frequency.

5 test methods

5.1 Environmental conditions required for testing The device under test should work in its normal working environment. a) Temperature. 15 ° C ~ 35 ° C; b) Relative humidity. 20%~75%. 5.2 Test results and uncertainty The complete test result expression should consist of the following parts. a) measured values and corresponding limits; b) Measurement uncertainty. The measurement uncertainty should not be greater than the values in Table 3. Table 3 Measurement uncertainty Project uncertainty Frequency ±1×10-7 Power (below 100 GHz) ±6 dB Humidity ±5% Temperature ± 1 ° C 5.3 Test Configuration 5.3.1 Test fixture Equipment manufacturers are required to provide appropriate fixtures to allow the equipment to be placed in a stable position and to ensure that the equipment antenna is in the same water as the test receiver antenna Flat line. As shown in Figure 1. The test fixture requirements are as follows. a) The matching load of the joints and waveguides used in the test shall be 50Ω; b) The joints and waveguides used in the test shall be matched to the load standing wave ratio of not more than 1.5; c) The receiving antenna gain should be no less than 20dB. Figure 1 Schematic diagram of the test fixture 5.3.2 Test site The test site shall be a fully shielded room with RF absorbing material in the room to simulate the free space environment in which electromagnetic waves propagate. It is Complete the replacement site for the device's radiation emission test. The test arrangement of the measuring antenna, the device under test and its alternative antenna is the same as the open test field Like, but their erection height from the floor is fixed. as shown in picture 2. The test site requirements are as follows. a) The shielding efficiency of the anechoic chamber used in the test shall be greater than 105 dB; b) The anechoic chamber return loss used in the test shall be greater than 30 dB; c) The equipment used in the test, the measuring antenna and the replacement antenna should be calibrated regularly. Figure 2 Test site 5.3.3 Test Block Diagram For the equipment specified in this standard, the test block diagram shown in Figure 3 should be used for testing. The test attachment requirements are as follows. a) The matching load of the mixer, signal generator, waveguide flange, etc. used in the test shall be 50Ω; b) The VSWR of the mixer, signal generator, waveguide flange, etc. used in the test shall be less than 1.5; c) The mixer, signal generator, waveguide flange, etc. used in the test should be calibrated periodically. Figure 3 test block diagram 5.4 Peak equivalent isotropic radiation power 5.4.1 Test Block Diagram The peak equivalent isotropic radiated power shall be measured using the test site described in 5.3.2 and the method in 5.3.3. 5.4.2 Measurement steps The measurement steps are as follows. a) Connect the device under test to a matching diode detector or equivalent via a suitable attenuator. Diode detection The output of the unit should be connected to the vertical channel of an oscilloscope or equivalent power measuring device. Diode detector and oscilloscope The combination should be able to accurately reproduce the duty cycle of the transmitter output signal; b) Use the spectrum analyzer to measure the output power of the transmitter, using the RMS detection method. At this time, the device under test should use the highest power. Level launch. The observed value is recorded as A; c) The peak equivalent isotropic radiated power Ppeak shall be calculated from the measured power output A and the observed duty cycle x, detailed The calculation method is shown in equation (1). Ppeak=A 10×lg(1/x) (1) In the formula. Ppeak---peak equivalent isotropic radiation power in decibel milliwatts (dBm); A --- measured output power in decibel milliwatts (dBm); x --- Transmitter output signal duty cycle. 5.5 Frequency range 5.5.1 Test Block Diagram The frequency range shall be measured using the test site described in 5.3.2 and the method in 5.3.3. 5.5.2 Measurement steps The measurement steps are as follows. a) the transmitter is adjusted to the maximum transmission mode; b) Use the spectrum analyzer to read the start frequency and cutoff frequency of the signal envelope and record it, the value of which shall not exceed the 4.2.2 mid-limit requirement. 5.6 Out-of-band emission 5.6.1 Test Block Diagram Out-of-band emissions shall be measured using the test site described in 5.3.2 and the method in 5.3.3. 5.6.2 Measurement steps The measurement steps are as follows. a) the transmitter is adjusted to the maximum transmission mode; b) Set the spectrum analyzer start frequency = 73.5GHz, cutoff frequency = 76GHz, RBW = 1MHz, VBW = 1MHz, detector Mode RMS, the maximum tracking mode is maintained; c) record the maximum value of the out-of-band emission, the value of which shall not exceed the limit of 4.2.3; d) Set the spectrum analyzer start frequency = 77GHz, cutoff frequency = 79.5GHz, RBW = 1MHz, VBW = 1MHz, detector Mode RMS, the maximum tracking mode is maintained; e) Record the maximum value of the out-of-band emissions, the value of which shall not exceed the mid-limit of 4.2.3. 5.7 Occupied bandwidth 5.7.1 Test Block Diagram The occupied bandwidth shall be measured using the test site described in 5.3.2 and the method in 5.3.3. 5.7.2 Measurement steps The measurement steps are as follows. a) the transmitter is adjusted to the maximum transmission mode; b) Set the spectrum analyzer center frequency = the center frequency of the channel under test, RBW = 1MHz, VBW = 1MHz, sweep width 2 times the nominal channel bandwidth, the detector mode RMS, the tracking mode maximum is maintained; c) Record the bandwidth of the 99% of the signal displayed on the spectrum analyzer. 5.8 Transmitter spurious emissions 5.8.1 Configuration Requirements If the transmitter uses an antenna array that distributes power symmetrically, only one transmit link (antenna) should be reserved, where practicable, Disable other transmit links (antennas) and, if not feasible, document the method used in the test report. If only one transmit link is tested, the test results should be corrected to apply to the entire system (all transmit links). One The transmit power (mW) of the transmit link needs to be multiplied by the number of transmit links to obtain the total transmit power of the system. The device under test should be configured to operate at the maximum duty cycle and maximum output power level. 5.8.2 Stray emission test method not greater than 40 GHz 5.8.2.1 Test Block Diagram When detecting spurious emissions less than or equal to 40 GHz, use the test site described in Appendix A and the relevant measurement procedures in Appendix B. Make measurements. 5.8.2.2 Measurement steps The measurement steps are as follows. a) Measure spurious emissions in the range of 30MHz~1GHz, set the spectrum analyzer RBW=100kHz, VBW=100kHz check Wave filter RMS, tracking mode maximum value is maintained; b) measuring spurious emissions in the range of 1 GHz to 40 GHz, setting the spectrum analyzer RBW = 1 MHz, VBW = 1 MHz detector RMS, the tracking mode maximum is maintained; c) Any emissions found in the scan that are within 6 dB below the limit shall be recorded. If the measurement is outside the specified distance To carry out, the calculation result of the equivalent field strength value should be given. 5.8.3 Spurious emission test method greater than 40 GHz 5.8.3.1 Test block diagram When detecting spurious emissions greater than 40 GHz, measurements shall be made using the test sites described in 5.3.2 and the methods in 5.3.3. 5.8.3.2 Measurement steps The measurement steps are as follows. a) Test the spurs of the highest frequency band and record when the device supports, set the spectrum analyzer RBW=1MHz, VBW= 1MHz, detector RMS, tracking mode maximum hold; b) Any emissions found in the scan that are within 6 dB below the limit shall be recorded. Analyze the mixer for the results The impact of mirroring. 5.9 Receiver spurious emissions 5.9.1 Configuration Requirements If the receiver is in the form of an antenna array, only one transmit link (antenna) should be reserved, and other emissions should be disabled, where practicable. Link (antenna), if not feasible, the method used should be documented in the test report. If only one receive link is tested, the test results should be corrected to apply to the entire system (all receive links). The spurious transmit power (mW) of a receive link needs to be multiplied by the number of receive links to obtain the total receiver spurious emissions of the system. Shooting power. The device under test should be configured to operate in a state of continuous reception or no transmission. 5.9.2 Stray emission test method not greater than 40 GHz 5.9.2.1 Test Block Diagram Use the test site described in Appendix A and the relevant measurement procedures in Appendix B when detecting spurious emissions less than or equal to 40 GHz. Make measurements. 5.9.2.2 Measurement steps The measurement steps are as follows. a) Measure spurious emissions in the range of 30MHz~1GHz, set the spectrum analyzer RBW=100kHz, VBW=100kHz check Wave filter RMS, tracking mode maximum value is maintained; b) measuring spurious emissions in the range of 1 GHz to 40 GHz, setting the spectrum analyzer RBW = 1 MHz, VBW = 1 MHz detector RMS, the tracking mode maximum is maintained; c) Any emissions found in the scan that are within 6 dB below the limit shall be recorded. If the measurement is outside the specified distance To carry out, the calculation result of the equivalent field strength value should be given. 5.9.3 Spurious emission test method greater than 40 GHz 5.9.3.1 Test block diagram When detecting spurious emissions greater than 40 GHz, measurements shall be made using the test sites described in 5.3.2 and the methods in 5.3.3. 5.9.3.2 Measurement steps The measurement steps are as follows. a) Test the spurs of the highest frequency band and record when the device supports, set the spectrum analyzer RBW=1MHz, VBW= 1MHz, detector RMS, tracking mode maximum hold; b) Any emissions found in the scan that are within 6 dB below the limit shall be recorded. Analyze the mixer for the results The impact of mirroring.

Appendix A

(normative appendix) Test site for radiation testing A.1 open test field or semi-anechoic darkroom Open test or semi-anechoic darkrooms shall comply with the requirements of the test site in Appendix A of GB/T 9254-2008. In the frequency band below 1 GHz, the test distance of the transmitting and receiving antennas is not less than 3 m. Select the appropriate test in the frequency band above 1 GHz distance. The size of the device under test should be less than 20% of the test distance. The height of the equipment to be tested or the height of the replacement antenna frame is 1.5m, the measurement day The height of the wire frame is adjusted within the range of 1m~4m. In order to ensure that the reflected wave signal generated by obstacles near the test site has no effect on the test results, the test site should meet the following requirements. condition. a) There shall be no conductive objects in the vicinity of the test site that are larger than the test maximum frequency λ/4 (λ is the wavelength of the electric wave); b) Connect the cables as far as possible along the floor surface, preferably under the floor, and shielded cables for low-impedance cables. A typical test site layout is shown in Figure A.1. Figure A.1 Test site layout A.2 Full anechoic chamber A.2.1 Overview The full anechoic chamber is a fully shielded room with RF absorbing material inside, which is used to simulate the free space environment of electromagnetic wave propagation. It is Complete the replacement site for the device's radiation emission test. The test arrangement of the measuring antenna, the device under test and its alternative antenna is the same as the open test field Like, but their erection height from the floor is fixed. See Table A.1, Table A.2 for the requirements for the shielding effectiveness and wall reflection loss of the full anechoic chamber. Requires full-wave darkroom to be tested The deviation of the space transmission loss from the device to the measuring antenna to the transmission loss in the free space environment is within ±4 dB. Table A.1 Requirements for shielding effectiveness of full anechoic chambers Frequency Range Shielding effectiveness minimum limit dB 10kHz~100kHz 60 100kHz~30MHz 80 30MHz~40GHz 105 Table A.2 Requirements for wall reflection loss of all-wave darkroom Frequency Range Minimum reflection loss limit dB 30MHz~100MHz 10 100MHz~300MHz 22 300MHz~40GHz 30 A.2.2 Test antenna The physical size of the measuring antenna cannot exceed 20% of the test distance. The measuring antenna should be suitable for the reception of polarized waves and should be installed at the level The end of the arm should allow the antenna to be positioned and mounted according to the horizontal or vertical component of the measured electric field. When oriented vertically and at the lowest When installing the position, the low end of the antenna should be at least 0.3m from the ground. A.2.3 Alternative ante......
Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 36654-2018_English be delivered?

Answer: Upon your order, we will start to translate GB/T 36654-2018_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 36654-2018_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 36654-2018_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.