GB/T 3489-2015 English PDFUS$189.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 3489-2015: Hard metals -- Metallographic determination of porosity and uncombined carbon Status: Valid GB/T 3489: Historical versions
Basic dataStandard ID: GB/T 3489-2015 (GB/T3489-2015)Description (Translated English): Hard metals -- Metallographic determination of porosity and uncombined carbon Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H16 Classification of International Standard: 77.160 Word Count Estimation: 9,941 Date of Issue: 2015-12-10 Date of Implementation: 2016-07-01 Older Standard (superseded by this standard): GB/T 3489-1983 Quoted Standard: ISO 4499-1-2008 Adopted Standard: ISO 4505-1978, MOD Regulation (derived from): National Standard Announcement 2015 No.38 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the metallographic determination of porosity and the presence, type and distribution of non-carbonized carbides. GB/T 3489-2015: Hard metals -- Metallographic determination of porosity and uncombined carbon---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Hardmetals.Metallographic determination of porosity and uncombined carbon ICS 77.160 H16 National Standards of People's Republic of China Replacing GB/T 3489-1983 Carbide Determination of Porosity and Nonchemical Carbon (ISO 4505. 1978, MOD) 2015-12-10 released 2016-07-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China China National Standardization Management Committee released ForewordThis standard is drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 3489-1983 "Determination of the porosity of cemented carbons and metallocene of non-condensed carbon". Compared with GB/T 3489-1983, the main technical changes are as follows. --- the standard chapter has been adjusted; --- increase the normative reference documents; - the contents of the "sample preparation" were modified; - Modifies the part of the original standard that differs from ISO 4505. 1978. This standard is amended by the re-drafting method using ISO 4505. 1978 "Cemented Carbide Porosity and Non-Zinc Carbon Determination". The technical differences between this and ISO 4505. 1978 and the reasons are as follows. - to increase the normative reference documents to meet the technical situation in China, the adjustment of the situation is reflected in Chapter 2 "normative reference file". For ease of use, this standard has been modified as follows. --- part of the chapter to increase the number. This standard is proposed by China Nonferrous Metals Industry Association. This standard is owned by the National Committee for the Standardization of Nonferrous Metals (SAC/TC243). The drafting unit. Xiamen Jinlu Special Alloy Co., Ltd., National Tungsten Materials Engineering Technology Center, Zigong Carbide Co., Ltd., Zhuzhou Cemented Carbide Group Co., Ltd. The main drafters of this standard. Zhang Shouquan, Fan Zhili, Sun Xiaoyu, Jiang Yuanxiang, Lin Xiaoxuan, Cao Wanli, Liu Tiemei. This standard replaced the previous version of the standard release. --- GB/T 3489-1983. Carbide Determination of Porosity and Nonchemical Carbon1 ScopeThis standard specifies the metallographic method for the presence, type and distribution of carbide and non-carbonated carbides.2 normative reference documentsThe following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article Pieces. For undated references, the latest edition (including all modifications) applies to this document. ISO 4499-1..2008 Metallographic determination of microstructure of cemented carbide - Part 1. Metallographic photographs and descriptions (Hardmetals- Metalographicdeterminationofmicrostructure-Part 1. Photomicrographsanddescription)3 instruments and equipment3.1 Metallographic microscopes, or other suitable instruments that can be viewed and measured on the screen at the required magnification. 3.2 Equipment for preparing samples.4 Preparation of sampleFor the metallographic test of the sample grinding surface, should be no wear marks and polishing scratches, and should pay attention to avoid the peeling of particles, so as not to cause the porosity Wrong judgment. The specific steps of the preparation of the test specimen shall comply with the provisions of ISO 4499-1..2008 6.1. Note. There are several methods for the preparation of cemented carbide metallographic tests. First, carefully grind, in order to ensure that the true organization of the exposed alloy, need to have enough Grinding amount. After grinding with a fine diamond wheel, and then in fine plastic, fine felt tray or paper tray, with the particle size gradually reduced to 1μm diamond grinding Paste or diamond powder for polishing.5 steps5.1 The maximum size of the pores on the grinding surface is defined as the size of the pores. The existence of cracks or cracks to develop special reference standards. 5.2 less than or equal to 10μm pores, 100 times the magnification or.200 times to observe the grinding surface of the sample, to assess. Should be detected adequately Represents a certain area of the sample grinding surface, according to the magnification used, compared with the picture in Figure 1 or Figure 2. Refer to the corresponding standard chart Tablet, reported the level of porosity, denoted as A02, A04, A06 or A08. 5.3 > 10μm ~ 25μm pores, 100 times under magnification to observe the sample grinding surface, to assess. Should be tested to fully represent the sample grinding surface Of a region, compared with the picture in Figure 3. Refer to the corresponding standard picture, reported the level of porosity, recorded as B02, B04, B06 Or B08. 5.4 For inspection of pores larger than 25 μm, the test shall be carried out at an appropriate magnification of less than or equal to 100 times, ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 3489-2015_English be delivered?Answer: Upon your order, we will start to translate GB/T 3489-2015_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 3489-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3489-2015_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 3489-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3489-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
