GB/T 33624-2017 PDF EnglishUS$200.00 · In stock · Download in 9 seconds
GB/T 33624-2017: Rolling Bearings - Test and Assessment Methods for Cleanliness Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 33624-2017: Rolling Bearings - Test and Assessment Methods for Cleanliness---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33624-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 21.100.20 J 11 Rolling Bearings – Test and Assessment Methods for Cleanliness Issued on: MAY 12, 2017 Implemented on: DECEMBER 1, 2017 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. 3. No action is required - Full-copy of this standard will be automatically & immediately delivered to your EMAIL address in 0~60 minutes. Table of ContentsForeword ... 3 1 Application Scope ... 4 2 Normative References ... 4 3 Terms and Definitions ... 4 4 Measuring Principle ... 6 5 Environmental Conditions for Measurement ... 6 6 Measuring Equipment, Appliances and Materials and Washing of Appliances ... 6 7 Measuring Procedure ... 6 8 Cleanliness Assessment ... 10 Annex A (Normative) Measuring Method for Dust Fall Quantity on Unit Area of Cleanliness Test Room ... 12 Annex B (Normative) Cleanliness Measuring Equipment, Appliances and Materials and Washing of Appliances ... 14 Annex C (Normative) Blank Experiment Procedure and Effective Filtration Area (EFA) Calibration Procedure ... 18 Annex D (Informative) Cleanliness Limits of Radial Ball Bearings ... 19ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard was proposed by China Machinery Industry Federation. This Standard shall be under the jurisdiction of the National Standardization Technical Committee on Rolling Bearings (SAC/TC 98). The drafting organizations of this Standard. Hangzhou Bearing Test and Research Centre, Jinfa Bearing Co., Ltd., Tianma Bearing Group Co., Ltd., Ningxia Qinchang Rolling-Bearing Manufacturing Co., Ltd., National Bearing Products Testing Centre, Zhejiang XCC Group Co., Ltd., Zhejiang Huanyu Bearing Co., Ltd., Zhejiang Chentong Bearing Co., Ltd. The main drafters of this Standard. Zhang Yajun, Chen Fanghua, Xu Jingxian, Zhao Liya, Li Xianhong, Shi Dafang, Liu Changming, Yang Weichun, Zhang Xunlei, Luo Qing, Zhang Xiaopeng, Zhang Baoming, Chen Lingfang, Li Xinglin. Rolling Bearings – Test and Assessment Methods for Cleanliness1 Application ScopeThis Standard specifies the test and assessment of cleanliness of rolling bearings (hereinafter referred to as bearings) and bearing parts. This Standard applies to the test and assessment of all kinds of open bearings and closed bearings before greasing, as well as the test and assessment of bearing parts.2 Normative ReferencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition dated applies to this document. For undated references, the latest edition of the referenced documents (including all amendments) applies to this Standard. SH 0004-1990 (2007), Solvent Oil for Use in Rubber Industry3 Terms and DefinitionsFor the purposes of this document, the following terms and definitions apply. 3.1 impurity Particles which adhere to the surface of bearings/bearing parts and are adverse to the performance of bearings. 3.2 particle size The maximum size of particles (the maximum distance between points on the contour line of the particle image map). 3.3 bearing/bearing part cleanliness The size of impurity on each bearing/each bearing part or the weight of unit surface area; the size and quantity of impurity particle on each bearing/each bearing part or wash the appliances once again as specified in B.3 or carry out blank test once again after using filtration membrane of pore size 0.45 μm to filter the solvent once again. 7.2 Measuring procedure of weighing method 7.2.1 Liquid sample preparation 7.2.1.1 Unless the cleanliness of the samples is so poor that the filtration speed of the liquid samples is lowered, multiple sets/pieces may be washed and measured together with the weighing method. 7.2.1.2 No scrubbing shall be carried out for the samples after opening package. 7.2.1.3 Soak cleaning. Use solvent to soak the samples in a container for more than 2 h; shake or rotate them one by one to make the impurity on the surface of the samples fall off to come into solvent. The use level of solvent shall ensure the samples are fully soaked in the container more than 10 mm. 7.2.1.4 Ultrasonic cleaning. Wash the samples twice by ultrasonic cleaning, 2 min for each time of cleaning. The use level of solvent for each time shall not be less than 200 mL and the height of solvent in the container shall not be lower than two times of the height of the samples. Multiple sets/pieces are allowed to be washed, but the samples are not allowed to be overlapped or staggered. 7.2.1.5 Washing of the samples with grooves or curls. Use solvent in the washing bottle to wash the surface of the samples to fully wash away impurity; collect the washings into the container. 7.2.1.6 All washings are liquid samples. 7.2.2 Preparation and weighing of filtration membrane 7.2.2.1 Use tweezers to take 2 pieces of filtration membrane of pore size 1.2 μm to place into two weighing bottles marked “Test (s)” and “Control (k)”; place them semi- openly into the thermostatic chamber for drying for 60 min at 60°C ± 5°C; put on the cap for them before placing them into the desiccator for cooling for 30 min; then use the analytical balance to weigh the two filtration membranes respectively; record them as ms1 and ms2. The filtration membranes shall be dried and weighed twice; the difference between the two weighing results shall not be greater than 0.2 mg; if the difference is greater than 0.2 mg, carry out drying and weighing once again and the final weighing results shall prevail. 7.2.2.2 Use tweezers to take out the filtration membranes from the weighing bottles; place in solvent to soak them before placing them flatwise on the microporous filter, with the control membrane (k) as the lower membrane and the test filtration membrane (s) as the upper membrane. 7.2.2.3 Press the upper funnel on the filtration membrane; use the clamping device to clamp the upper funnel, filtration membranes, microporous filter, lower funnel and up to 50 μm; greater than 50 μm up to 100 μm; greater than 100 μm. 7.3.3 Liquid sample preparation and counting filtration membrane preparation 7.3.3.1 Prepare liquid samples as specified in 7.2.1.2 ~ 7.2.1.6. 7.3.3.2 Select one filtration membrane of appropriate pore size in accordance with the minimum counting particle size; use tweezers to clamp the filtration membranes for soaking before place flatwise on the microporous filter. 7.3.3.3 Carry out liquid samples filtration and impurity collection as specified in 7.2.2.3 ~ 7.2.2.5. 7.3.3.4 Use tweezers to take down the filtration membranes from the microporous filter and place flatwise in the weighing bottle. 7.3.3.5 Place the weighing bottles semi-openly in the thermostatic chamber for drying for 60 min at 60°C ± 5°C; then put on the cap for them before placing them into the desiccator for cooling for 30 min 7.3.4 Counting procedure 7.3.4.1 If the samples need to be assessed using the weighing method and the particle counting method in combination, the use the test filtration membrane as the counting filtration membrane and the control filtration membrane without counting. 7.3.4.2 Use tweezers to take out the counting membrane from the weighing bottle; place flatwise carefully on the filtration membrane fixer tray; put on the cover before mounting to the clamping device on the stage of the microscope. 7.3.4.3 In accordance with the minimum counting particle size, select the objective lens of appropriate power; carry out lightness adjustment and shade correction for the microscope; set the diameter of effective filtration area, diameter of counting area, size of minimum counting particle, size segment of counting particles and other parameters; carry out scanning, particle size measurement and quantity statistics for the counting filtration membranes. 7.3.4.4 Output measuring results in accordance with the assessment items. The assessment items may include but not limited to the total count of particles larger than the minimum counting size, the count of particles of all size segments, the count of reflective particles of all size segments and the count of non-reflective particles, the maximum particle size and so on. 7.3.4.5 If there is any dispute in the large particle size, the auxiliary function of the image analyser may be used to identify its morphology on the view screen; then the computer system may be used to remove the small overlapping particles for the staggered particles and then output the measuring results o... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 33624-2017 be delivered?Answer: The full copy PDF of English version of GB/T 33624-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 33624-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33624-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33624-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 33624-2017?A step-by-step guide to download PDF of GB/T 33624-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 33624-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
