GB/T 32363.2-2015 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB/T 32363.2-2015: Plastics -- Polyamide (PA) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 32363.2-2015: Plastics -- Polyamide (PA) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT32363.2-2015 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.080.20 G 32 GB/T 32363.2-2015 / ISO 1874-2.2012 Plastics – Polyamide (PA) Moulding and Extrusion Materials – Part 2. Preparation of Test Specimens and Determination of Properties (ISO1874-2.2012, IDT) Issued on: DECEMBER 31, 2015 Implemented on: JUNE 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Preparation of Test Specimens ... 6 4 Conditioning of Test Specimens ... 9 5 Determination of Properties ... 10 Appendix A (Normative) Specimen Preparation Using Laser Sintering ... 13 Appendix NA (Informative) Chinese Documents corresponding to International Documents in Normative References ... 14ForewordGB/T 32363 Plastics – Polyamide (PA) Moulding and Extrusion Materials is divided into two parts. --- Part 1. Designation System and Basis for Specification; --- Part 2. Preparation of Test Specimens and Determination of Properties. This Part is Part 2 in GB/T 32363. This Standard was drafted as per the rules specified in GB/T 1.1-2009. This Part’s translation equivalently adopts ISO 1874-2.2012 Plastics – Polyamide (PA) Moulding and Extrusion Materials – Part 2. Preparation of Test Specimens and Determination of Properties. See Appendix NA for Chinese documents that have consistent relationship with international documents in the normative references of this Part. This Part makes the following editorial changes. --- Add informative Appendix NA. This Part was proposed by China Petroleum and Chemical Industry Federation. This Part shall be under the jurisdiction of Subcommittee of Engineering Plastics of National Technical Committee for Standardization of Plastics (SAC/TC 15/SC 9). Drafting organizations of this Part. Shanghai Kingfa Sci.& Tech. Development Co., Ltd., Kingfa Sci.&Tech. Co., Ltd., China BlueStar Chengran Research Institute of Chemical Industry, and Nanjing Julong Engineering Plastics Co., Ltd.. Participating drafting organizations of this Part. Pingdingshan Shenma Engineering Plastics Co., Ltd., Jiangsu Kingfa Sci.&Tech. New Materials Co., Ltd., Zhejiang Juner New Material Co., Ltd., Jiangsu HS New Material Stock Co., Ltd., and Shanghai Kingxi Lab Co., Ltd.. Chief drafting staffs of this Part. Zhang Yong, Xia Jianmeng, Yuan Sahoyan, Shi Xin, Wu Bo, Liu Qixiang, Cai Tongmin, Liu Lirong, Qin Xinying, Tian Jibo, Wu Jianguo, Liu Guo, and Chen Guangqiang. Plastics – Polyamide (PA) Moulding and Extrusion Materials – Part 2. Preparation of Test Specimens and Determination of Properties1 ScopeThis part of GB/T 32363 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyamide moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods that are suitable and necessary to characterize polyamide moulding and extrusion materials are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this Part, as are the designatory properties viscosity number and tensile modulus of elasticity given in ISO1874-1.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this standard. ISO 62 Plastics - Determination of Water Absorption ISO 75-2 Plastics – Determination of Temperature of Deflection under Load – Part 2. Plastics and Ebonite ISO 179-1 Plastics - Determination of Charpy Impact Properties – Part 1. Non-Instrumented Impact Test ISO 179-2 Plastics – Determination of Charpy Impact Properties – Part 2. Instrumented Impact Test Appendix NA (Informative) Chinese Documents corresponding to International Documents in Normative References GB/T 1033.1-2008 Plastics - Methods for Determining the Density of Non-Cellular Plastics - Part 1. Immersion Method Liquid Pyknometer Method and Titration Method (ISO 1183-1.2004, IDT) GB/T 1033.3-2010 Plastics - Methods for Determining the Density of Non-Cellular Plastics - Part 3. Gas Pyknometer Method (ISO 1183-3.1999, IDT) GB/T 1034-2008 Plastics - Determination of Water Absorption (ISO 62.2008, IDT) GB/T 1040.2-2006 Plastics - Determination of Tensile Properties - Part 2. Test Conditions for Moulding and Extrusion Plastics (ISO 527-2.1993, IDT) GB/T 1043.1-2008 Plastics - Determination of Charpy Impact Properties - Part 1. Non-Instrumented Impact Test (ISO 179-1.2000, IDT) GB/T 1408.1-2006 Electrical Strength of Insulating Materials - Test Methods - Part 1. Tests at Power Frequencies (IEC 60243-1.1998, IDT) GB/T 1409-2006 Recommended Methods for the Determination of the Permittivity and Dielectric Dissipation Factor of Electrical Insulating Materials at Power, Udio And Radio Frequencies Including Meter Wavelength (IEC 60250.1969., MOD) GB/T 1410-2006 Methods of Test for Volume Resistivity and Surface Resistivity of Solid Electrical Insulating Materials (IEC 60093.1980, IDT) GB/T 1634.2-2004 Plastics - Determination of Temperature of Deflection under Load - Part 2. Plastics, Ebonite and Long-Fibre-Reinforced Composites (ISO 75-2.2003, IDT) GB/T 2035-2008 Terms and Definitions for Plastics (ISO 472.1999, IDT) GB/T 4207-2012 Method for the Determination of the Proof and the Comparative Tracking Indices of Solid Insulating Materials (IEC 60112.2009, IDT) GB/T 5169.16-2008 Fire Hazard Testing for Electric and Electronic Products - Part 16. Test Flames - 50W Horizontal and Vertical Flame Test Methods (IEC 60695-11-10.2003, IDT) GB/T 9345.4-2008 Plastics - Determination of ash - Part 4. Polyamides (OSP 3451-4.1998, IDT) GB/T 11997-2008 Plastic - Multipurpose Test Specimens (ISO 3167.2002, IDT) GB/T 12006.1-2009 Plastics – Polyamides - Part 1. Determination of Viscosity Number (ISO 307.2007, IDT) GB/T 32363.1-2015 Plastics – Polyamide (PA) Moulding and Extrusion Materials - Part 1. Designation System and Basis for Specification (ISO 1874-1.2010, IDT) GB/T 17037.1-1997 Injection Moulding of Test Specimens of Thermoplastic Materials - Part 1. General Principles and Moulding of Multipurpose and Bar Test Specimens (ISO 294-1.1996, IDT) GB/T 17037.3-2003 Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 3. Small Plates (ISO 294-3.2002, IDT) GB/T 17037.4-2003 Plastic - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 4. Determination of Moulding Shrinkage (ISO 294-4.2001, IDT) GB/T 19466.3-2004 Plastics - Differential Scanning Calorimetry (DSC) - Part 3. Determination of Temperature and Enthalpy of Melting and Crystalliation (ISO 11357-3.1999, IDT) ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 32363.2-2015 be delivered?Answer: The full copy PDF of English version of GB/T 32363.2-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 32363.2-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 32363.2-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 32363.2-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 32363.2-2015?A step-by-step guide to download PDF of GB/T 32363.2-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 32363.2-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
